DRZ 400 valve check, checking valves and making adjustments, I'm not a professional so anyone can do it. of course its entertainment. enjoy. DRZ400
Пікірлер: 33
@Flyin_high_pnw2 жыл бұрын
Thank you for taking the time to make this video. I've never adjusted my valves myself on my DRZ. I've probably watched this video three or four times now and it's really making me anxious to want to try myself. Snow is melting fast and riding season is upon us in my area so I'm afraid if I don't get it right I'm going to lose ride time 🤣 seriously though, thank you!👊🏼
@joeymac837Ай бұрын
Great video, i'm down east in Nova Scotia I have a 2018 DRZ400S, I do a lot of riding has 31000 kms on it now, I'm getting a lot of deceleration pops when I let the throttle go but none in acceleration and It stalls every week or so once then takes a few min to start again but will run fine in between, starts up real easy, I am going to check the clearances and take the carb off and clean it, I use an NGK iridium spark plug and only use supreme fuel.
@antik_adam2 жыл бұрын
Great video! Just did an install of stage 1 hotcams, however my tolerances were way too tight on the exhaust side, this is definitely going to help!
@s.y.b.10463 жыл бұрын
Thx a lot !! it is very well made . this video add so much confidance to only use the factory maintenence guide . It will help for changing to stage 1 HOT CAMS ;)
@giorgiomusitelli20693 жыл бұрын
Easy and clear, THANKS!
@bill52743 жыл бұрын
Great video thx for sharing!
@VenganzaCayey3 жыл бұрын
Thank you for charing. just subscribed
@shannonhartnett3 жыл бұрын
Great vid mate cheers
@jamescornflake154218 күн бұрын
Hello. I done this job. I think it will be ok.I have a question. I read that I must verify that my cams are getting oil. I read that I must take out the bung beside the Tensioner. I did and have turned the engine over using the starter with the plug removed. Please tell me why no oil has come up so far. ( New oil and new filter). Thank you.
@jamessouthworth16994 ай бұрын
I was hoping this bike did NOT have the bucket/shim style valves.
@motomaddness48374 ай бұрын
I feel that they are a better system and not quite daunting once you have done it a few times.
@giovanhagarАй бұрын
The DR 650 has rocker arms with screw adjusters.
@Yaschua Жыл бұрын
First time doing this, I’ve got the line at TDC, but my cams are pointing in instead of out…any suggestions?
@motomaddness4837 Жыл бұрын
rotate till cam lobes are like in the video and check for the line in the sight hole, 4 stroke so you may be on the wrong stoke.
@kurtkeltner91402 жыл бұрын
Is there anything special to reset timing chain when you put it back in? Like tighten or loosen or you put it all back together and it’s fine?
@JohannesDalenMC2 жыл бұрын
When you/he said «take note of the orientation before taking off the cams», he ment the lobes right?
@motomaddness48372 жыл бұрын
There are markings on the cam gears so you get it back into the same spot.
@peternielson4815 Жыл бұрын
Ok ok ok thanks
@krislambert66252 жыл бұрын
Hi,do you have to remove the spark plug to check the valves?
@davidhoward89512 ай бұрын
What year model is that
@kontrollme90342 жыл бұрын
My cam covers refuse to come off, everything is loosen. Still trying to figure how to take it off for the past weeks
@Agamemnon92 ай бұрын
Did you get it?
@Treeclimbingexpert5 ай бұрын
It looks so scary so much to do.
@grimace85603 жыл бұрын
starts at 4:40
@oscarbustamante348910 ай бұрын
You from Wisconsin?
@motomaddness483710 ай бұрын
nope, northren Alberta Canada
@shanebrothers80792 жыл бұрын
Wow, never gotten motion sickness from a how to video before. very informative but the camera work literally missed the mark.
@jamesdoes5763 жыл бұрын
Is this the same engine as ltz 400? Bc mine won't start it pops out flames but no start
@jamesdoes5763 жыл бұрын
kzfaq.info/get/bejne/aZ6hlZeYqbmbemQ.html
@motomaddness48373 жыл бұрын
BJ it looks the like the same engine however I can only see the one side. I would check the values and cams, could of slipped a tooth on the cam.