23 January 2023, Thank you for the video, it helped me a lot with the zone programming on the HS2016-4 Neo (With HS2LED keypad) I used to install Honeywell, FBII Alarm panels and the DSC programming is not the same. Pretoria, South Africa

This saved me today thanks!

This is great timing, I just bought a Neo to upgrade my 2500 DSC system, just bought the house. Thank you for taking the time to make these videos. I would be interested in a video about partitions and how they work. thanks again Fred K.

thanks this has given me a headway for wireless configuration

Informative video, thanks from India

any video on how to add zones to partitions?

Huge! Thank you!

What D&D class do you play Jason? Great video though, thank you.

Good stuff here

What are the partitions used for, and this is the important question, pgm2 you said it resets automatically after disarm, can’t I have my smoke detectors be 24 hour even if the sys is disabled and I use the *72 or 70 something to system reset the pgm? I’m using a high output board with fire alarm horns and this is in a building so I need the pgm 2 to always to active even Disarmed

How do you turn up the volume

How do you mute a bell/siren on a DLS5 system ? Need to test al the zones...

Hello And thanks for the video, i think that the problem that i have is related with the pgm configuration,I have a 1x pc1864 1x PC5204 3x 5108 On the third 5108 they are 4 glassbreakers 1 glassbreaker sensor of then connect directly to the 1864 (aux+-) which works, The other 3 connected to the 5204 (aux/01) and the panel show them as always on Also we have a motion sensor that doesn’t activate when is movement . That is connected to the 5204(aux/01) I have others two movement sensor connected Sensornumber-label-zoneDefinition-Module/Card-CurrentCableConnected-Status 25- ComedorGlassbreaker-3-PC5204-Aux/01-NotWork 26- Hallentradamovimiento-5-PC5204-red/black-Works 27- Livingroomglassbreaker-3-PC5204-Aux/01-NotWork 28-Familyroommotion-5-5204-Aux/01-NotWork 29-Familyroomglassbreaker-3-5204-Aux/01-NotWork 30-Kitchenglassbreak-3-1864-aux+/aux--NotWork 31-Hallarribamovimiento-5-5204-red/black-Works 32-Cuartopplmovimiento-5-1864-aux+/aux-Works I did an experiment!. changing from 5204 aux/01 to red & black the error disapears from the panels, the sensor blinks when they are activated, but the panels doesnt register the changes. also the other glassbreaker sensor that was working before, stop working!. any comments? Thanks in advance

awesome very helpful.

How does one program the PG9901 Wireless Indoor Siren to work with this Neo Alarm System?

I have a PC1616 with LED keyboard and can't figure out how to program zones. Looks like numbers of digits don't match...

Can you all show how to wire a M2M mini to the neo so they can use the Rconnect app. i have been told 5 different ways and none seem to work with the Rconnect app.. so they can use their phones to work the system thanks if this can be done

How many wireless devices can you have on one zone?

Can you explain how to program Zone Attributes and what each zone attribute means?

Hi, on NEO is it possible to turn off the communication error for internet loss, in our community interest work done late at night and sick of panel beeping during the down time. also, is there a way to make the LCD keep pad not beep when taking the screen but beep when zones open?

I have an HS2032 but it has installed lockout enabled. It clicks rapidly when I plug it in. Shorting pgm1 and zone 1 didn’t work. My old 5010 had a reset procedure by shorting 4th pin on chip to pgm1 and this removed the installer lockout. The hs2032 does not have a chip eeprom like my old 5010. Any ideas how to remove the installer lockout from this neo hs2032 ??

First of all tnx for a very informative video, the only thing i did not see is how to see the ID number of the e.g detector compared to the zone its attached/programed to, any easy way to see that ? tnx...

Bosch 6000 is the go .

How do we set up a system test in 10 minutes, can you help?

Good video Como puedo descargarlo en español por favor

I can set Away, without and entry alarmed element. Out entry is similar to a mall storefront Gate. How can I program the away option to work without an entry trigger, it defaults to stay without it, so the motion sensor won't work.

Hi , how can i save time and date when after power off and on back the system?

How to restore zone tamper

i followed your instructions. All my doors and windows are set. however, the keypad still shows all zones I entered as 'open'. any idea how to secure them?

What’s settle delay mean?

I'm trying to connect a 2 wire door contact (2 of them) to the same zone. But it seems like only one of them works at a time. Each on their own works ok, the minute I add 2 of them, the whole zone stops working and opening any windows doesn't trigger any status difference on the alarm. But each one triggers the right status on the alarm when they are pluged in by themselves. Any ideas what i'm doing wrong?

does the Neo uses the PowerG sensors?

Nothing like the system I have, and I’ve spent twenty minutes trying to find it on line. Too many G.D, models!

Hi alarm system store. Can you have multiple fire zones? can zones 1, 2, 3, and so on be fire zones?

My dcs panel is decrease time 1 second in every 24 hours. How can i solve it.??

I deactivated my monitoring service which was set up through wifi instead of land line. Since then I have been getting a trouble 4 failure to communicate. I have tried a few things from the web with no luck. Do you have any suggestions on how I can stop the unit from sending out a signal?

DSC is a very bad system. My sensor and keypad all stopped responding to the main panel. Error message was Responding Communication main panel fail. Had the unit for 6 years and it just stopped working. Don’t wast your money on DSC system. I’ve installed 6 of these and all have the same problem.

Informative but wayyyy too much time wasted on entry and exit delay.

At minute 1:56....you should have shown how to default Panel, to Factory Default, to start OVER programming, as if it has been programmed previously......... YOU will NOT know the "installer Code" as it may have CHANGER to another installer CODE, other than "5555".......it will NOT accept 5555, if programmed previously .... You will NOT be able to get into programming.... Thanks

31:59 I bet you do

No focus, meandering from one setting to another, (while puffing on a cigarette. Uh... ya know?) To improve this video would require a script, so to keep moving forward and minimalize the long "Uh... ya know?" pauses. I couldn't finish it, kept loosing interest and wanted to read the manual instead, maybe that was the insidious reason behind this video? Hmmmm.