Dspiae ES-P electric pen, portable, cordess, low speed, 3mm, grinder, drill, sander, polisher, tool

Рет қаралды 9,298

Жыл бұрын

Very compact and easy to use tool for the scale modeler. Internet says can charge to 80% in 30 minutes and fully charged in 60 minutes. Uses mainstream Dremel style 3.0mm tool bits.
Internet also says 5000/10000/18000 RPM but highly doubt it based on how slow it cuts plastic at the highest speed.
#dspiae #esp #grinder

Пікірлер: 17

@MrFish1968 Жыл бұрын

I just bought one with the 9 bit set and also sanding disks, I build plastic model kits and I think that is where this will shine, especially as a nice paint mixer. Plus the 3mm shank makes is compatible with a massive range of bits for polishing sanding etc.

@jonflanagin6682 9 ай бұрын

Just bought it and i love it , so far so good.

@arclementsjr 6 ай бұрын

I also own this tool and on the main box it says the rpm at setting 1 is 5000, setting 2 is 10000 and setting 3 is 18000.

@RaNmA5886 Жыл бұрын

The bit Set ist very usefull, i Like it. You can Drill holes with the needle bit, but i would Like to have a Drill Bit for it. But i found nothing that fits. PCB Drill Bits are 3.175 and the Dspiae fits only 3mm Bits... Thanks for the Video, regards from Germany

@PeteCourtier 8 ай бұрын

Love mine but it’s a shame it doesn’t take 3.25mm shank bits! Had to buy a separate Chuck.

@joemoore4027 4 ай бұрын

Nice too ,but you only limited to using DSPIAE bit and acessorie's. Very limited selection. You can get a chuck to use other bits but they do not run true and break very fine drills. It's basically a small compact grinder.

@Wilett614 4 ай бұрын

You can Indeed get a "Precision" chuck to fit a 3 MM arbor . I made one : ) Works AWESOME especially when I need to Drill Small holes . I can fit ANY SIZE diameter tool in the collets up to and including .125 inch .

@Kenyj5bv Жыл бұрын

Can you please confirm? Are the white spots (Example @12:00) on the body of the pen came from the factory or just dust/plastic particle? Thanks man!

@tomcarrington1086 Жыл бұрын

Hi, thanks for the preview.. Where did you order the extra tools for it please? I have one and cannot find where to buy them. Thanks, Regards, Tom

@RaNmA5886 9 ай бұрын

Hi i have bought the 5mm sanding disk's and ITS make fun. You can sanding in small areas. Very usefull. It,s good to Sand Nub Marks down and get a smoth Finish. But i have 1 Problem. My Pen Draw Batterie Status very fast. I charge It at 100% and don't use it for 2 weeks...and the Akku was at 0%... It that normal? I try it 3 Times but every time the Same Problem...

@smallmodelcollector 9 ай бұрын

There's probably no battery management so maybe it slowly loses power like a car battery does. I use mine more often so haven't noticed anything wrong.

@blue2824 7 ай бұрын

Where do you get one?

@TheRealSzyszka 2 ай бұрын

best price link please ?

@hernanrodriguez5082 Жыл бұрын

How long does the battery last fully charged?

@smallmodelcollector Жыл бұрын

No idea, sorry. Would depend how hard you grind too.

@hernanrodriguez5082 Жыл бұрын

@@smallmodelcollector thanks. Sorry but I was talking about when You storage it for a long time. Does the battery drain fast if stored for a long time?

@smallmodelcollector Жыл бұрын

@@hernanrodriguez5082So far mine has never been found dead after the months I've had it. I'm sure it loses power slowly like anything with an internal battery. I'd charge it every few months if you are worried.