Dual Axis Solar Tracker Arduino Tinkercad | Tinkercad Project | Arduino Project | LDR With Servo
Рет қаралды 20,114
Күн бұрынDual Axis Solar Tracker | Arduino Project | led chaser | Tinkercad project | Electronic Project | Engineering Project | Diploma Project | Major Project | Min Project | Block coding
Project Code
drive.google.com/file/d/1_zu7...
website - Eazytronic.com
Electrical & Electronic project Visit our website
eazytronic.com/
Tinkercad is also a free online web browser & Simple to simulate the electronic project
Tinkercad Website Link :- www.tinkercad.com/
#1 Getting Started With Tinkercad in English || This Tutorial for Complete Beginners
• #1 Getting Started Wit...
Getting started with Tinkercad In Hindi
• Getting started with T...
Distance measure with LCD using Ultrasonic
• 29 Distance measure wi...
Arduino Tutorial at Tinkercad in Hindi / English
Our motive is to teach robotics to the students. if you have any doubt you can ask from the comment section..
#arduino #tinkercad #simulator
If project are helpful than please Support us
Paytm UPI ID - 7007651787523@paytm
Paypal ID - adnanecps@gmail.com
Any Help WhatsApp me 7007651787
@RahulKushwaha-zl9kx Жыл бұрын
Which servo is to be connected in which pin, like vertical servo in which pin and same for horizontal??
@eazytronic9394 Жыл бұрын
Horizontal servo connect pin 9 Vertical Servo connect pin 10
@jagan5785 4 ай бұрын
what is the use of solar panel here and can you please tell what is the positioning of ldrs i can't understand what topleft and top right mean
@eazytronic9394 2 ай бұрын
Detail is given in discription
@maciejolejnik6706 Жыл бұрын
It will be run on esp32 ?
@eazytronic9394 Жыл бұрын
Yes
@srihari1992 5 ай бұрын
Three mortar drive, 3 rd one is flower , how to make ?.
@eazytronic9394 5 ай бұрын
Not understand
@kennethjamero4075 7 ай бұрын
it will be run on arduino uno?
@eazytronic9394 7 ай бұрын
Yes it work
@aufanurfaizhaedar4423 Жыл бұрын
why are you using 10k ohm resistor on ldr, can you explain
@eazytronic9394 Жыл бұрын
With a pull-up resistor, the input pin will read a high state when the button is not pressed. In other words, a small amount of current is flowing between VCC and the input pin (not to ground), thus the input pin reads close to VCC. When the button is pressed, it connects the input pin directly to ground. The current flows through the resistor to ground, thus the input pin reads a low state. Keep in mind, if the resistor wasn’t there, your button would connect VCC to ground, which is very bad and is also known as a short.
@yarenberber2246 Жыл бұрын
how can i get all the codes
@eazytronic9394 Жыл бұрын
Code link also given in description
@yarenberber2246 Жыл бұрын
@@eazytronic9394 THANKS
@eazytronic9394 Жыл бұрын
@@yarenberber2246 Welcome
@bigstudio5628 7 ай бұрын
Can I use a nano board?
@eazytronic9394 7 ай бұрын
Servo motor
@eazytronic9394 7 ай бұрын
Yes Arduino nano
@bigstudio5628 7 ай бұрын
thank you @@eazytronic9394
@HayderHassouna 3 ай бұрын
i have some question pleasevcan you help me
@eazytronic9394 3 ай бұрын
Okk
@oscarkhor234 10 ай бұрын
Can I add your contact number please, I would like to see photos of solar tacker's realistic connection method. Because I want to reproduce a similar solar tracker but I don’t know how to connect those wires in reality.
@eazytronic9394 10 ай бұрын
WhatsApp+917007651787
@srihari1992 5 ай бұрын
@@eazytronic9394good sir
@secrezztoo7419 8 ай бұрын
If it's for solar panels, where does it connect? because I did this project...
@eazytronic9394 8 ай бұрын
Solar cell connect with battery
@secrezztoo7419 8 ай бұрын
@@eazytronic9394 so for the power supply what do you use?
EAZYTRONIC
Рет қаралды 1,7 М.
IoT Projects Ideas
Рет қаралды 74 М.
Experimentalist
Рет қаралды 73 М.
EAZYTRONIC
Рет қаралды 11 М.
Sustainable Every Day
Рет қаралды 52 М.
Rachel De Barros
Рет қаралды 443 М.