Ducati V2 Streetfighter and Panigale V2 Oil Change Procedure

No video

Ducati V2 Streetfighter and Panigale V2 Oil Change Procedure

Рет қаралды 3,146

Күн бұрын

Here is a video showing the Ducati V2 Streetfighter and Panigale V2 Oil Change Procedure. Only additional step on the Panigale is the bodywork removal and reinstallation. Hope this helps and please let us know if you have any questions or additional tips in the comments. Please like and subscribe and well be adding more videos soon.
Also give us a follow on Instagram. NW_Track_Addicts

Пікірлер: 25

@toniostyle 6 ай бұрын

Great video. Thanks. I think overnight is overkill. But I understand. It’s your bike

@nwtrackaddicts 6 ай бұрын

Definitely overkill but we had the time.

@pd9rd 29 күн бұрын

Thanks for the explanation and video! What is the paddock stand you have for the back?

@nwtrackaddicts 29 күн бұрын

That's the pit bull large hub stand. Works on both the V4 and V2 along with all the large hub models. Highly recommend the Pit bull stands. Been using them on the stack for 15 plus years.

@pd9rd 28 күн бұрын

@@nwtrackaddicts Thanks! Let's see if I can get my hands on one in Europe.

@omarandpedro Ай бұрын

didn't mention installing the drain bolt, but the oil stayed in. 14 Nm?

@nwtrackaddicts Ай бұрын

I believe we torqued to 14 Nm but always check again the service manual.

@aas061 6 ай бұрын

Nice work mate! 8 Nm for the oil filter plug isn’t much. On the v2 panigale its’s 13 Nm IIRC

@nwtrackaddicts 6 ай бұрын

Thank you, appreciate it. Our local dealer spec's 8 nm for the oil filter cover bolts on both the V2 Panigale and Streetfighter.

@SICSLIPKNUT 3 ай бұрын

Yeah it's deff 8nm

@ducatininja3866 6 ай бұрын

Did you run the engine, then let it sit before rechecking the oil level or did you check the oil level from cold?

@nwtrackaddicts 6 ай бұрын

Yes, once oil filled, ran engine till operating temperature was good, (about 15 minutes at 70 degrees ambient temp). Run longer or shorter depending on ambient Temps, typically 15 minutes is sufficient. Then let it sit for an hour to make sure. If additional oil is needed add a small amount then repeat the run/let sit process until at the right level. It's a bit overkill but this ensures the level is good.

@George-cv7nm 6 ай бұрын

Great video! Thank you. Are the bolts that you used to pull off the oil filter cover them M8 - 1.25 X 50mm bolts then? Thanks for verifying.

@nwtrackaddicts 6 ай бұрын

Thank you, hope it's helpful. Use (2) M8x1.25 2" machine bolts for the V2, (3) bolts on the V4.

@nwtrackaddicts 6 ай бұрын

50mm or 2" work great, extra length helps with the leverage pulling it off.

@juanabreu5138 5 ай бұрын

Drain plug link or part number to buy it please thanks

@nwtrackaddicts 5 ай бұрын

Here is the part. I ordered it from MotoD. It's manufactured by RaceBolt. Racebolt Stainless Race Drilled Magnetic Drain Bolt M14x1.5x12 RB-SSSUMP1412MR

@twowheelin7361 6 ай бұрын

What’s the deal with the safety wire? Prevents them coming loose?

@nwtrackaddicts 6 ай бұрын

That's correct, prevents critical items from coming loose. Not really necessary when riding on the street but we safety wire a good amount of items for track riding.