Duramax Y-Bridge Full Install (EGR Delete)

Рет қаралды 295,575

Күн бұрын

WCFAB Full EGR/Ybridge Install on my 2007 LBZ 4x4 Duramax diesel. !!!!SUBSCRIBE!!!!
Product link www.ebay.com/itm/401122915979
Egr Delete video Full Install: • Duramax Full EGR Delet...
Gaming KZfaq channel: / @rrorgaming
Channels to check out:
Backroaddiesel
/ @cornerstoneperformance
JW Montoya
/ @jwmontoya
Bertrand850
/ bigstallion80
EFI Live DSP5 Switch Idaho Rob
K&N Cold Air Intake
Billet Turbo Wheel upgrade
WCFAB YBridge
FASS Titanium 150GPH Lift Pump
FASS Fuel Sump Kit
MBRP 3inch Turbo Down pipe
Magnaflow 5 inch turbo back
Cat/muffler delete
Onboard Oil Filtration System
PPE Race fuel valve
Ported fuel fitting
Transgo Jr Shift Kit
Resonator Delete
Egr Delete
Egr Cooler delete
PVC Reroute
PPE Stage 5 Built Transmission
Zone off-road upper control arms
PPE Stage 3 HD Tie Rods
6" Pro-comp suspension lift kit
5100 Bilstien Shocks
35/12.50/R20's
20x12 Vision Prowlers -51 offset
Wehrli Custom Fabrication is an Industry Leader in Duramax Diesel Turbo Kit's and Custom Performance
Parts. On the fore-front of Diesel Performance and product development we strive in producing the best
product on the market. You can rest assured that with the purchase of our products you will receive the best
quality, fitment, customer service, and performance for your truck.
WCFab LBZ/LMM 3” Y-Bridge Kit is an upgraded high flow intake kit for the 2006-2010 Duramax. The factory
Y-bridge is a poorly designed two piece bridge that is prone to blowing apart under boost and creating poor
drivability and excessive smoke. This is a one piece fabricated 3” bridge with a heavy duty machined
beadroll on the end so the pipe cannot deform when the t-bolt clamp is tightened. This kit allows you to
remove the EGR system for race use only. A 3” high flow intercooler pipe compliments the y-bridge to offer
a full 3” tract from intercooler to engine. This 3” Y-Bridge kit will work in conjunction with our S400 over
stock Twin Turbo Kit if you decide to upgrade in the future.
3” Full Fabricated 1 piece High Flow Y-Bridge
3” High Flow Cold Side Intercooler Pipe
½” Heater Hose and Clamp
Silicone Boot and T-Bolt Clamps
Powder Coating color of choice (please specify)

Пікірлер: 504

@yoyomurph9613 5 жыл бұрын

I've seen so many videos that just say what they're gonna do, show the engine before and then show it done, SOMETIMES they show a few things they take off or do a cut and tell you where they fkt up. Your "bolt by bolt" videos are out-freakin-standing. It's what people are looking for (IMO) when they're diggin' for these videos. Thanks Troop.

@tylerfast5936 Жыл бұрын

Lmao I know right. You see a video labeled exactly what your looking for and there going on about there personal life story for social media followers.

@twe3zet745 Жыл бұрын

I agree

@jamestambone1858 3 жыл бұрын

Do not change anything in your videos,this is exactly the video's I like to watch,I just got my first duramax an your videos are extremely helpful!!

@TruckMaster 3 жыл бұрын

Thanks

@motohead38 5 жыл бұрын

had my turbo clamp break, didn't do any damage to my turbo thank goodness, still having it rebuilt. I took it to my diesel performance place they wanted 3000.00 to replace turbo, i brought it back home, took me 6 hours just to get off all the heat shields, I have a 7.5 lmm 3500hd dually I had the performance shop delete my egr.(blocker plate). and put a tune in about a year ago. well anyhow I got the turbo out, at the shop getting rebuilt 500.00 ordered my billet turbo wheel, will be here monday. also ordered the complete wcfab pipe kit, i figured i saved 2500 doing it myself so i put the money to the kit. cant wait to get it. I told them you were the one that turned me on to them as i watch all your videos very helpful. Keep up the great vids, and next year when we roll on thru to Lakeport, Mi for our vacation maybe we can grab a coffee at a truck stop and ill show off my rig....:). again thank you for the videos helped me out alot. p.s. I hope wcfab gives you a new free pipe for your drivers side. tell them Jeff said you deserve it for all your hard work..

@ronmower3694 5 жыл бұрын

7.5 wat

@KeithAllenPerformance 7 күн бұрын

Thanks you man for taking the time to show exactly how everything should be taken off and installed. I love seeing videos like these. Before I would have never tackled the EGR delete, but after watching video man I believe I will tackle it! I just ordered the same setup from WC Fab. Thanks man and also Thank You for your service brother

@anonymous4507 5 жыл бұрын

I ‘m a diesel mechanic, and I really do enjoy your videos. Your camera work is awesome. You are very thorough as well. I have a 2006 LBZ that I am going to do this on, so this helped me out a bunch. Thank you. One suggestion, and I am sure someone else in the comments told you too, but always replace o-rings, and gaskets with new. It’s just not worth the headache of getting it all put together, and something leaks because of reusing old shit. When you are installing o-rings use Sil-Glide. It’s a silicone based o-ring lubricant. It really helps to keep from tearing the o-ring. It’s good stuff. Thank you again for all the information you provide.

@LKN4WAR 3 жыл бұрын

Anon ymous thanks for o ring recommend on the lube. 👍

@NextLevelTruth Жыл бұрын

Interesting, where’s the best place to get new Y bridge gaskets?

@JeffRigney 5 жыл бұрын

Tip! wrap your universal (swivel) with a wrap or two of electrical tape so it doesn't "flop" ! or put a piece of heat shrink tape on it.

@saloram990 2 жыл бұрын

thank you

@jkreviea 3 жыл бұрын

Great video. When I worked on the line at Dmax, we used soapy water to lube the tubes with o-rings for installation.

@BBR_Voiles89 5 жыл бұрын

Really well made video, I'm not mechanically inclined in the slightest and I want to change that and you've inspired me and provided a lot of learning material I appreciate what you're doing

@KP0117 3 жыл бұрын

Dude you have the Best videos on KZfaq... we all love them!!!

@TruckMaster 3 жыл бұрын

Thanks 🙏

@111silvrbck 4 жыл бұрын

1st off thanks for your service! Appreciate the the detail on install, I have an LLY being upgraded with WCFab Y-bridge kit and piping along with intake! Love all of videos much needed DIY info!👍

@jacksonbruce1498 Жыл бұрын

Will a lbz y bridge kit fit the lly?

@35057 6 жыл бұрын

Tips and tricks for a pita job like this are just gold! Thanks a ton! Looks killer and I’m sure it performs it too.

@TruckMaster 6 жыл бұрын

+Bayer-Z28 thanks brother

@avaleemullin23 3 жыл бұрын

Thanks alot man you helped me greatly just got done doing the hsp y bridge in my lbz. It was a pain but your videos helped a lot!

@noname_ZX6R 2 жыл бұрын

i just bought my lbz last week and it had a boost leak when i bought it. i made a boost leak tester myself and tracked the leak down to the y-bridge. the pipe that connects the y-bridge to the cold side pipe had popped out. same exact issue you had actually. your videos help so much man. thank you!

@ant4l-224 2 жыл бұрын

Quick question I bought both and Egr delete kit and the same y bridge in this video before my Egr delete kit get here do I even need it because the red elbow pipe replaced the blue one

@sickboy8831 5 жыл бұрын

just subscribed just bought my first duramax keep up the great work and thank you for your service

@bildrrick 6 жыл бұрын

I wish I had seen your video before I did my egr delete on my lly! Every step you described I was shaking my head yes to. Then when you used the flex head to get the lower rear nuts loose I yelled genius! The egr deletes when I did mine reused that faulty gm y bridge so I didn’t change it but now I will! Thanks!

@TruckMaster 6 жыл бұрын

+BildrRick The Eclectic Nomad good luck! You got this

@longgoneg60 2 жыл бұрын

Thank you for making this. My lbz pass. side gasket on the Y bridge failed(shortly after heater core line drenched hot engine) Using this as a guide to remove mine now to replace the gaskets. I greatly appreciate it man.

@TruckMaster 2 жыл бұрын

Thanks! 👍

@durabat4607 6 жыл бұрын

Great video! My LBZ already has the Sinister Diesel setup but my dad has a LBZ as well only stock. His EGR is giving his 40k mile truck issues already, so I'm going to recommend this kit. By the way, love the channel. I subscribed a few months back when I bought my truck and have watched about all your Duramax videos. I appreciate all the hard work, it helps a lot!

@oscarsalinas7708 Жыл бұрын

Hello, after watching many of your videos I would like to know your opinion, which engine is better for heavy duty work, Duramaz or Powerstronw

@stewartparker741 6 жыл бұрын

I’m a new subscriber. I own a 2007 LBZ dually and I’m currently in school for diesel tech. I really like your videos man almost bought one of the evergreen EGR deletes until i watched this. Step by step process is great enjoy watching these.

@TruckMaster 6 жыл бұрын

+stewartparker741 that’s awesome glad you like them and best of luck in your future career

@Wretched2JZ Жыл бұрын

Well don’t buy a WC either! It’s over priced for what you get! Not to mention the route it takes directly over the alternator 😂🙈. What were they thinking!

@raymondsteed4552 6 жыл бұрын

Really enjoy this Channel, have the same truck and your videos are awesome

@zanedebuse7109 6 жыл бұрын

This video is going to save me when putting everything back together thanks man

@TruckMaster 6 жыл бұрын

+Zane Debuse no problem

@roburbina2174 5 жыл бұрын

Thank you so much for the videos. I love all the time you take to show every single bolt and every single step. I'm taking my 05 to get deleted at the shop. I'd love to do it myself but it's my work truck and I need the tax write-off. I have to spend money on maintenance. The mechanic recommended up pipe replacement and EGR valve block off plates. I'd like to do the high flow pipe and y bridge like your video

@TruckMaster 5 жыл бұрын

Thanks and good luck to you

@ericroberts891 3 жыл бұрын

I really enjoy your videos man, got my first diesel which is a white CCSB 4X4 SILVERADO LBZ A couple years ago and have started doing a few mods to it.

@binthavone 3 жыл бұрын

Your the man !!!!....you killed me with the extensions I was crying when I seen that but it gets it done...just hilarious

@truckguyjoe 6 жыл бұрын

Great job. Nice detail on the entire process.

@TruckMaster 6 жыл бұрын

+truckguyjoe thanks joe

@jesusleon2247 5 жыл бұрын

Love ur videos man ! I just got a duramax and am getting it build !!

@dylancameron6177 3 жыл бұрын

Ordered mine today! Thanks for the video!

@thegreatalberta9189 6 жыл бұрын

Great video. Love your detail on how to do it yourself. Will be get help to lots of people seeing as there's not a lot out there for duramaxs

@TruckMaster 6 жыл бұрын

+Rick Aubin thanks for the support man and your right it’s hard to find how to‘ South there

@carlosgudiel67 6 жыл бұрын

Your truck is amazing man. I’m going to work on mine to get it where it needs to be

@SilverJ56 6 жыл бұрын

I just subscribed!!!! You are the genuine deal!!! 2009 LMM... I want to put all of your mods on my truck!!

@TruckMaster 6 жыл бұрын

+Jonny Dingo that’s awesome man I appreciate it

@lancetrujillo3155 5 жыл бұрын

Thank you for the video, super helpful. Happy Memorial day and thank you for your service!

@TruckMaster 5 жыл бұрын

Thanks

@brianyetzke5970 6 жыл бұрын

Yes your details definitely help thx

@ronaldbabbitt6318 2 жыл бұрын

Awesome brother 🏁 Alot of helpful tips like always, Y bridge is so critical. Lmm in Colorado 🤠 thanks Truck Master!

@tylermears480 7 ай бұрын

Thanks man for the videos extremely helpful. When you installed new y Bridge I didn't see the gaskets but imnsure there in there haha thanks man

@anefalaniko4702 Жыл бұрын

When I replaced the CP3 on my truck I replaced the crossover bridge too because it was see better days. I replaced the it with the exact bridge you have and it’s great

@lucasseymour869 6 жыл бұрын

Great job man. Another tip is to loosen the turbo hold down bolts so you can get more room to the back bolts.

@NextLevelTruth Жыл бұрын

Which bolts are you referring to? So loosen the turbo enough to move it a little? Trying to do all my home work before I dive in.

@lucasseymour869 Жыл бұрын

@@NextLevelTruth Yeah there are I think 3 or 4 bolts that hold down the turbo. Loosen then enough so you can move the turbo a bit. Search for turbo install for the bolts I'm talking about.

@audiok7 4 жыл бұрын

I just did the egr delete and pvc rerouting and wcfab y bridge but now I have a low coolant level light on my dash . I'm not sure why I can use some help , thank you , you have done an awesome job

@Frostytravels 6 жыл бұрын

another great video man.....excellent work

@TruckMaster 6 жыл бұрын

+Frosty 8415 thanks

@timvarnadoe5456 8 ай бұрын

Thank you for the detailed info in this video! I greatly appreciate it and very helpful!

@Sprinkles4911 5 жыл бұрын

You had a hell of a lot easier time doin this than I did lol but good video you're very informative

@TruckMaster 5 жыл бұрын

Thanks

@guuguguguggug 6 жыл бұрын

Awesome video good job!

@RobertHolster1 Жыл бұрын

Hey Battle, been doing Truck Master Marathons...finding old gems like this. Who else does what you do, and by yourself? Not many. Respect...

@robertrogina5433 5 жыл бұрын

In the process of installing my Y bridge. I did find a couple of bolts that I hate.

@maysonmcintyre374 6 жыл бұрын

Your videos are awesome and very helpful..thank you

@TruckMaster 6 жыл бұрын

+mayson mcintyre no problem glad I can help!

@bigmike2971 6 жыл бұрын

Great vid as always bro. I see them bolts kicked your behind. Lol. I said I was gonna take sometime to get them back bolts off but u did your thang and glad u enjoying it. Glad u took our advice on WCFab Now gone turn that beast up. Nothing else to blow out boost

@TruckMaster 6 жыл бұрын

+bigmike2971 after I check for leaks I hope everything is tight

@bigmike2971 6 жыл бұрын

Truck Master I think u knocked that problem out. I guess boost leak down tester will give u that answer. Think I may make my own they are a little pricey

@gregpepple423 6 жыл бұрын

Another excellent video !!

@magnus22001 3 жыл бұрын

thanks brother this video was super helpful

@AndyGarcia-ch1ci 6 жыл бұрын

The flexible extension would’ve been perfect, I used a swivel and electric tape to the nuts on the socket to hold it in place till I could thread them. Also tried the magnet but mine doesn’t stay tight enough to turn the nut onto the threads it would just spin. Good job buddy congrats

@nickmartushev3759 6 жыл бұрын

Really good videos man helps out a lot. Just don't re-use old gaskets/ seals even if they look good replace them with new ones

@TruckMaster 6 жыл бұрын

+jungle juice do you think I should of used rtv?

@nickmartushev3759 6 жыл бұрын

Rtv is fine, I'm just saying with old gaskets or seals there could be hair line fractures in it that u can't see, that's y it's normally best to replace with new ones.

@pjtruesdale16 4 жыл бұрын

Watched this video, went and checked mine and it’s doing the exact same thing. So I’ll be referencing this video again when my new bridge gets here haha

@TruckMaster 4 жыл бұрын

👍

@bradybashon3941 6 жыл бұрын

Nice work man! Another thing to do is take the up pipe off and replace it with a lb7 up pipe or 2" performance up pipes. Or do what I did and cut the egr bellow right at the pipe and weld a peice of metal on it. The egr bellows are known for bursting with plates and also it gives better straight on flow to the turbo for better spool. Just a pointre and heads up!

@TruckMaster 6 жыл бұрын

+Brady Bashon thanks for the idea I guess that will be my next upgrade now

@turbogrin 2 жыл бұрын

This is really going to help me as I bought a 06 with one head removed and everything off the top! I will be rebuilding the engine and will not be putting things back to stock! A new Y bridge and EGR delete will be in the picture !

@Brandon56784 6 жыл бұрын

Looks great!!! Nice work!!!

@TruckMaster 6 жыл бұрын

+Brandon Etscheidt thanks man

@Gaffneydaniel92 Ай бұрын

Just another tip after I tackled this recently. A 1/4” flex extension and 1/4”10mm is easier to gain access underneath the turbo mouth and in front of the hard coolant line. With a 3/8 system I couldn’t get access to the nut because of the coolant line. My socket couldn’t fit .

@mrflyer11ify 6 жыл бұрын

Great video, Looking to do the same thing to my LMM as well as intercooler pipes.

@OILCOUNTRYCOLLECTIBLES 5 жыл бұрын

Good, useful video man. Thanks!

@MiguelHernandez-zi4gl 5 жыл бұрын

Truck master you’re the f’n man!!👍

@TruckMaster 5 жыл бұрын

👍

@solojoe175 5 жыл бұрын

Perfect video!

@jamesdean787 6 жыл бұрын

Yes Sir! removing bolts "Stevie Wonder style"! Thank You for your service. God Bless Merry Christmas

@TruckMaster 6 жыл бұрын

+James Dean lol your no joking! Thanks you too

@cantyoufeelthelove 4 жыл бұрын

great video man. Still slowing catching up to some of your mods although I'm really just keeping everything stock. I just want the truck to make 1 million miles before an engine build. Hopefully the last truck I "have" to buy.

@DaddytechEnt 6 жыл бұрын

*first time here, first thing from one veteran to AD Thanks for your service. I like the kit but it's kinda pricey but like my old boss used to say that's the kind of game if you wanna play you gotta pay. might as well pony up and pay for the good stuff before you start throwing good money in after bad for less results. Next you need to take that thing and have a proper tune put on it so you're not wasting so much fuel when you rug the pedal. also in order to make the thing hook up not sure if you have them or not but traction bars are a must keeps the rear end from twisting and causing wheel hop*

@TruckMaster 6 жыл бұрын

+DaddytechEnt fully tracking. Thanks for your service as well and very true about it being pricey

@shartedmypants 6 жыл бұрын

Thanks for sharing!!

@xbxspartan 6 жыл бұрын

very informative awesome video

@kymarx6672 5 жыл бұрын

Made it look easy my lly is much harder to do took 6 hours to pull the stock and 12 to put the new one in great video tho helped with most things!

@dakotalo92 5 жыл бұрын

duramax kyle how did you get the new one in

@ElPasoTom 4 жыл бұрын

Great video, thank you.

@STANGTHECOYOTE 6 жыл бұрын

Up pipes and manifolds next. Worth every penny imo.

@TruckMaster 6 жыл бұрын

+STANGTHECOYOTE very true

@choppertj1 5 жыл бұрын

This is too much for me to get into. Nice job and way to keep your cool.

@donbing3662 2 жыл бұрын

One other thing that should be mentioned. If you're removing your y-bridge and you have a aftermarket turbo that is any bigger than stock you will need to remove it in order to get the top left bolt out of the bridge.

@cesarlaso356 6 жыл бұрын

Took me the same time to do my y- bridge. I did mine after attempting your billet wheel install, I decided, I didn't want to do it twice. I also bought the boost leak tester yesterday before watching this video lol. Keep em coming truckmaster. Just a suggestion but have you looked into Cal tracs or traction bars? I get a lot of axle wrap and they are a must for traction. I just did the Merchant auto pump rub kit, my case was just about to get rubbed through by the pump, that would also be a good video. Berny fix is better and cheaper.

@TruckMaster 6 жыл бұрын

+cesar laso thanks for the advice I haven’t put a lot of thought into trac bars or tcase funny how we are thinking alike on the other stuff I hope I have no leaks because when I get on the throttle it still sounds like a woooosshhhh noise in the engine bay not sure if there still is a leak or the new pipe and bridge just make the truck sound better

@dustindd1 3 жыл бұрын

Bud I love the videos very explained I’ve been a mechanic purty much all my life but not for diesel but you have helped tremendously! Ty! I have an 04 duramax it does awesome it’s got the Diablo predator tuner on it! It’s ok but I’ve changed the egr block off and yes the cheap way I’m moving to the mountains and it’s a 6 hour trip one way I’ve not had any problems thank god except I broke the fork in the transfer case I rebuilt it works perfect changed the opening mouth piece for the turbo for better performance supposedly I’m very anal over my trucks I’m looking to make my diesel well not so much fast which it already is but my question to you is how to make more towing power without breaking the bank? I’ve been pulling my enclosed trailer and open car trailer to transport all my stuff from one house to another and when I get into the mountains well pulling up hill is not a problem but transmission gets very hot ! What I want is plenty of power towing not so much fast I want a reliable power house I’m planning on keeping the truck I just want when I hook to something I don’t want any doubts or well it’s going to run hot I’ve changed both thermostats hoses belts fluids etc I changed them probably more than the normal person yes I over do everything but I know I can get into any of my trucks and not worry! Any advice would help I think that’s one thing you haven’t addressed! About towing! Ty in advance!

@saloram990 2 жыл бұрын

you the best mr your videos you share we us are the only professional and educational yo give me the security to do it my self we to much confidence thank you very much for your knowledge

@TruckMaster 2 жыл бұрын

Thanks

@bassdaze 5 жыл бұрын

been watching here and there from probably one of your first vids where you installed egr delete kit... man those truly are junk, I have ine and had to replace o rings and have my kit pretty much zip tied to help secure it better...anyone with delete kit wishes they did the Y bridge instead, i know i do !! probably do mine next spring as im sure i have boost leak for sure there, take care

@ozziecrosby2092 4 жыл бұрын

Same here.

@recklessspeed7877 6 жыл бұрын

Nice video

@allen4779 6 жыл бұрын

Nice video great work looks good have a marry Christmas☃️☃️🎄🎄🎄🎄

@TruckMaster 6 жыл бұрын

+#### #### you To thanks!

@nathanjungers968 5 жыл бұрын

You made it look easy, I had a really hard time with it even using your tips and tricks. Also did an lb7 up pipe at the same time and a mbrp downpipe. I put the new gaskets on my y bridge and it was too tight, tried for about 3 hours to get it in place and just went back to the old gaskets. It was an experience but I'm gonna say ill pay someone next time!

@TruckMaster 5 жыл бұрын

I hear you it was tough for me as well my videos always look easy on camera for some reason

@inspire_greatness7464 6 жыл бұрын

Worth every penny!!!!

@TruckMaster 6 жыл бұрын

+Inspire_Greatness74 most definitely

@noahtw96 3 жыл бұрын

Love your videos! Always good tips for working on my LBZ. Quick question though, what kind of tank is bolted on to the plate next to do the a/c compressor? Is it an onboard air compressor?

@Wretched2JZ Жыл бұрын

Wiggled and pulled that intake tube out like a loose tooth! 😂

@dmax06 10 ай бұрын

Looks like you're ready to do my LBZ now!

@keithautterson9302 Жыл бұрын

I swear I'm right behind you on everything I watched your egr delete video's to delete my egr now I blew out my stock y bridge o rings also and need a real y bridge lol should've watched this video first lol

@stephenrockwell5282 5 жыл бұрын

Hey truck master love the install vid had a question. You know anyone with the pusher y bridge? Herd its got better flow than the wcfab but was curious of your opinion

@brennenmcguire8377 6 жыл бұрын

Great video man! I'm glad theres finally a video on youtube on how to do it! I pretty much did the same technique as you did! A little tip on LMMs (because its a little closer) is you have to loosen the 3 turbo pedestal bolts to slightly pry the turbo back to get to that top bolt out that hits the compressor housing. Thats what i did if anyone on here is working on LMMs lol. Good Job!!

@TruckMaster 6 жыл бұрын

+Brennen McGuire thanks for the tip very good to know

@tylersmith4424 6 жыл бұрын

Brennen McGuire I'm having issues with this right now and can't get the last two bolts for the pedestal to pry that back, if you could give me any more info on how you did it would be great

@brennenmcguire8377 6 жыл бұрын

Tyler Smith yeah man, the other two bolts are on the drivers side if you already loosened the passenger side one. You can’t see them, so what I did was I got my socket with an extension and feel for it (because you can’t see them.) Then I got a breaker bar and loosened them ( you might needa get a cheater pipe to bust them loose.) It’s a bit of a tight fit. I removed my glow plug controller as well. Do you have an idea on where the other two are?

@tylersmith4424 6 жыл бұрын

Brennen McGuire Yup I got the passenger side loose and can't see other two on drivers side, I removed the glow plug controller and that's as far as I got

@tylersmith4424 6 жыл бұрын

Brennen McGuire but no I really don't know where they are I'm stuck

@SwimbaitSamurai 4 жыл бұрын

Hey man I love the vids and I have a question. So I have an 05 LLY and I’m looking for the best Egr delete, what do you recommend and should I do the Down pipe at the same time?

@colinerickson4833 3 жыл бұрын

had the same issue ordered the high flow kit from WcFab Money Well Spend!

@705jrock 6 жыл бұрын

just got my y bridge installed. that was a pain in the butt.

@jerredwayne8401 5 жыл бұрын

I'm doing mine now and I am regretting this big time

@r81ders2012 6 жыл бұрын

This video help me out a lot thanks man I got the y bridge out, now just debating on what Y Bridge to purchase. Any tips?

@MrRaffaro 5 жыл бұрын

I made my own with a Huth bender and gloss black Krylon !

@alphaq179 5 жыл бұрын

I also have a couple questions for you about other projects if you have an email that would be great your videos are amazing on helping me and I hope you keep em coming

@BolteBuilt 5 жыл бұрын

Is that an airborne patch I see? I’m not in the military but always loved the airborne. Rumor is that you get an extra chute for the gigantic balls you have. Lol

@RobertKohut 6 жыл бұрын

Nice!

@GuacamoleAndOJ 5 жыл бұрын

Great video I’ll be using this to help me install my new y bridge. I’m brand new to these trucks but I have an 05 duramax with this same problem leaking boost in that spot. I assume that means I have the egr delete already? Why doesn’t that pipe fit properly in the first place? Like I said I’m not very knowledgeable lol

@natediddymaesavikenz6315 6 жыл бұрын

Nice videos really informative! Have sum questions on a 2006 chevy duramax. Can I call u to ask u sum questions? I'd really appreciate it. Keep them videos coming!!

@Chief392Smokeshow 6 жыл бұрын

Thanks for the videos was waiting on this video from you truck was down way to long hopefully next thing you do is the up pipe kinda need help on that

@TruckMaster 6 жыл бұрын

+David Phillips first week of January I will have that video done man

@Chief392Smokeshow 6 жыл бұрын

Truck Master thanks and what unit are you out of if you don’t mind me asking.

@MLGtroll365 6 жыл бұрын

Day 1 subscriber right here 💪😁☝

@TruckMaster 6 жыл бұрын

+TrollMaster300 what’s up!

@nicholaslask9897 3 ай бұрын

Idk how you do this with the cab still on the truck. for a full EGR delete I salute the guys who can keep a sane mind without lifting the cab

@jrosa-ik2mg Жыл бұрын

Hi Truck Master I want to say thank you for doing what you do, your videos and information you share are great source of knowledge. I have a question , what is the best turbo for your dollar$ on a 2007.5 duramax LMM . Thank you

@gerry6310 6 жыл бұрын

Just got an LMM do I have to do all the upgrades at once. Or can I do the full EGR delete first and the exhaust next. Also will I need a tuner before I even start. Great video!

@marcobrown8389 6 жыл бұрын

Great job man

@TruckMaster 6 жыл бұрын

+Marco Brown thanks

@manuelguerrero8688 10 ай бұрын

Thank you

@LD-zr4xz 6 жыл бұрын

Just got the money together to buy a 07 along with the credit union, I looked at it and knew right off that someone like me with a 4 level back fusion and some metal from the bad guys while in the military would need some help since bending in most any direction is almost impossible. I hope someone knows some one that lives in south west Tennessee or north west Georgia might give me a hand not looking for help for nothing but when you get whacked as bad as I did your in trouble physically. The truck I was lucky enough to get is a 07 with 73 thousand miles hope to get it done before it gunks up

@saltysteel3996 4 жыл бұрын

When doing the EGR delete, is a retune required? I have no tuning equipment and I don't know how to tune. So I would have to take it somewhere and pay more money for the tuning, if it's required. Thanks!