Dyson V8 - No power - red flashing LED

No video

Dyson V8 - No power - red flashing LED

Рет қаралды 12,373

Күн бұрын

So, this is a Dyson V8 vacuum cleaner and the issue is that it doesn't power on anymore, it only has that red LED light that starts flashing.
Usually, that red light means that the battery is dead and should be replaced. Well, this time is not the battery. It was a bit unexpected what I`ve found.

Пікірлер: 23

@Devicesdevices-et3mi Жыл бұрын

It's an important point you note here and great that you uploaded this. I was about to dispose a V8 battery due to red flashing light however I tested it on another V8 and it was fine all blue lights. Out of pure interest, I stuck the other battery into the broken unit and sure enough, it also flashed red. Nice as now have a spare battery at least. Later Edit: I did a quick continuity test of the two battery prongs that are exposed within the handle of the Unit once battery was removed. Sure enough there was a beep thus a problem/short between both. Must be the same issue you have here. Thanks again for posting.

@techfixPOV Жыл бұрын

I`m glad it helped! Cheers!

@mattelliott2940 6 ай бұрын

Lo 11:00

@cletusfordwicke7608 2 ай бұрын

Brilliant. Absolutely outstanding fix.

@techfixPOV 2 ай бұрын

Thank you!

@hanslauner7045 2 ай бұрын

Super Erklärung, ich musste den shit Schalter wechseln wegen der Sollbruchstelle.

@techfixPOV 2 ай бұрын

Glad it helped!

@JagaSantagostino 2 ай бұрын

Thanks! By the hal magnet test i was able to fix mine! It wasn’t touching anymore

@techfixPOV 2 ай бұрын

Glad it helped

@jameslarson6555 8 ай бұрын

Very well done video, thanks!

@techfixPOV 8 ай бұрын

Glad you liked it!

@a.f.s.3004 Жыл бұрын

Mine was flashing red too. Spent 25 bucks on a ryobi adapter, done. Runs perfect

@techfixPOV Жыл бұрын

I assume the problem was the battery. It's perfect if you found an alternative to the original Dyson battery.

@vincenth7731 Жыл бұрын

Super, merci pour cette vidéo.

@techfixPOV Жыл бұрын

Avec plaisir, je suis content que cela ait été utile.

@vincenth7731 Жыл бұрын

@@techfixPOV En réalité, ça ne m'a pas été utile pour réparer, mais je trouve que ta vidéo est très bien expliqué! et ça peut servir pour plus tard! . aujourd'hui je viens d'équilibrer les cellules d'une batterie Dyson V8 je les ai toutes mise à 3,811V, maintenant je dois acheter un PICKIT3 pour flasher le BMS ! .. tu t'y connais là dessus? merci

@birkan1 2 ай бұрын

Do you have any video which gives info about the thin red and white wires? What is the voltage of that and where is it connected? I have to test a dyson v6l motor without other parts just by itself and there is no info, I guess 3.3v or 5v but I want to be sure.

@birkan1 2 ай бұрын

And also about the blue wires, what do i need to make it run without reed sensor, a video about how to run dyson motor standalone would be nice

@techfixPOV 2 ай бұрын

Those wires are connected to the accessory connector for powering the brushes. There should be battery voltage when a brush is connected.

@birkan1 2 ай бұрын

@@techfixPOVthanks, How about the white connector?

@techfixPOV 2 ай бұрын

The white connector is from the hall sensor that will activate the boost function when you move the MAX button. It should work with this connector unpluged.