10.1 AURO 3D SETUP! | Denon | Marantz | Internal & External Amps

10.1 AURO 3D SETUP! | Denon | Marantz | Internal & External Amps | Hardware & Software

Рет қаралды 43,932

Күн бұрын

10.1 AURO 3D SETUP! | Denon | Marantz | Internal & External Amps | Hardware & Software
Hey fam! Here's a tutorial on how to setup a 10.1 Auro 3D configuration using your 9 channel Denon or Marantz AVR. I go over a few scenarios, including mostly internal amp usage all the way to powering ALL your speakers with external amps. Hope it helps! Check it out!
Emotiva BasX A3 - emotiva.com/products/basx-a3-...
Outlaw Audio Model 7000x - amzn.to/3P6LnIq
Marantz SR7015
Amazon - amzn.to/3F1VmcZ
B&H Photo - bhpho.to/3p9zWpb
Aperion Audio Braided Mono RCA Cable - www.aperionaudio.com/collecti...
=============================
MY HOME THEATER SETUP
=============================
65” LG CX OLED TV
Amazon - amzn.to/3lTcHMQ
B&H Photo - bhpho.to/2SDJpYg
Marantz SR7015
Amazon - amzn.to/3F1VmcZ
B&H Photo - bhpho.to/3p9zWpb
Outlaw Audio Model 7000x Amplifier
Amazon - amzn.to/3NO6oGZ
Peachtree Nova300 Stereo Integrated Amp
www.aperionaudio.com/collecti...
Emotiva BasX A3 Aplifier
emotiva.com/collections/amps/...
FRONT LCR
Aperion Audio Verus III V8T Towers
www.aperionaudio.com/collecti...
Aperion Audio Verus III Grand V6C Center Channel
www.aperionaudio.com/collecti...
FRONT WIDES & VOICE OF GOD
Aperion Audio Novus Slim N6SC LCR
www.aperionaudio.com/collecti...
SURROUNDS
Aperion Audio Verus III Grand V5B Bookshelf
www.aperionaudio.com/collecti...
SURROUND BACKS
Aperion Audio Novus N6T Tower Speakers
www.aperionaudio.com/collecti...
ATMOS HEIGHT SPEAKERS
Aperion Audio A5 Height Module
www.aperionaudio.com/collecti...
LG UBK90 4K Blu-ray Player
Amazon - amzn.to/2UtSnZ0
B&H Photo - bhpho.to/3zeOg1G
AppleTV 4K (4th Gen)
Amazon - amzn.to/3kGQ1R9
B&H Photo - bhpho.to/3eCueWU
Nintendo Switch
Amazon - amzn.to/2Tqra96
B&H Photo - bhpho.to/3x2Ea2B
14 AWG Copper Speaker Wire
Amazon - amzn.to/3cmGoCP
B&H Photo - bhpho.to/3dqdVMc
Monoprice Low Profile 22 Lb Capacity Speaker Mounts
Amazon - amzn.to/3ckelDM
=============================
MY VIDEO GEAR
=============================
Audio Interface - Focusrite Saffire Pro 40
Amazon - amzn.to/3stZ6y0
Sennheiser MKE600
Amazon - amzn.to/3slMidQ
B&H Photo - www.bhphotovideo.com/c/produc...
Sony A7 II Full Frame Mirrorless Camera
Amazon - amzn.to/3GJqFty
B&H Photo - bhpho.to/3GLtnik
Canon EOS Rebel T5i
Amazon - amzn.to/2Y432rp
DJI Osmo Mobile 3
Amazon - amzn.to/3cj0yNP
B&H Photo - bhpho.to/3x5PFa1
Shure KSM32 Cardioid Condenser Microphone
Amazon - amzn.to/2QEVuLr
B&H Photo - bhpho.to/3dpC3yQ
XLR Male to Female Microphone Cable
Amazon - amzn.to/3lYz1ED
B&H Photo - bhpho.to/2U6ikNH
JOILCAN 81" Tripod
Amazon - amzn.to/3hn7RoS
B&H Photo - bhpho.to/2Ua1LAr
=============================
LINKS
=============================
Everything you need can be found at the link below! Woohoo!
linktr.ee/ealanosborne
#auro3d #marantz #hometheater
=============================
CHAPTERS
=============================
0:00 Intro
0:27 Overview
1:51 Mostly Internal Amps_Connections
2:23 Mostly Internal Amps_Software
5:34 Front L/R External_Connections
6:35 Front L/R External_Software
8:35 Rear Height External_Connections
9:04 Rear Height External_Software
9:47 Preamp Mode_Connections
12:43 Preamp Mode_Software
13:55 Subwoofer(s) Connections
17:02 Trigger Cables Connections
17:44 Outro
=============================
DISCLAIMERS
=============================
I am a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for me to earn fees by linking to Amazon.com and affiliated sites

Пікірлер: 145

@byronhadley9662 2 жыл бұрын

Wow, these videos are coming out fast! Really appreciate the hard work and frequent uploads

@ealanosborne 2 жыл бұрын

Thanks! Had/have a couple trips planned with the fam, so I stacked several and scheduled them out just for y’all! 😁🤘

@kixxoff928 2 жыл бұрын

VERY nice and useful video. Other youtubers somehow are not that detailed in clarifying the physical connections, and, most importantly - AVR amp assigns. I am running Auto 3D setup without VOG channel (5.1.4). I prefer Auro over Atmos. For all movies I always use Auro.

@ealanosborne 2 жыл бұрын

Sweet! 🤘

@healthynutster Жыл бұрын

I’ve been into home theater since the &0’s and have upgraded accordingly as the formats have developed. I’ve never been blown away by Atmos, apart from a few very well done mixes. I believe the Auro speaker layout to be superior to Dolby’s and more compatible with the way humans actually hear. There’s a ton of poor Atmos mixes, and they can be greatly enhanced using Auro’s speaker layout and it’s upmixer. Everyone must make their own decision of course, but for me, this provides the greatest surround experience currently available.

@ealanosborne Жыл бұрын

Agreed! They really nailed it with the science of binaural human hearing 👍

@WayneGrant-bl2pq Жыл бұрын

I agree 100% with you, I was into multi-channel sound in the 70’s with my quadraphonic receiver and Auro 3D is on another level (pardon the pun). Atmos has some benefits with moving some sounds around, but Auro 3D is an environment. Watching a baseball game is exciting to me now, movies and music have a more flavor from what they were before. Atmos only works with their encoded movies, Auro 3D works with everything. I predict, Auro 3D will one day have objects added and that will be another leg up for Home Theater.

@1Aquadon 11 ай бұрын

Thanks Elan.. Your simple straight forward approach is awesome. Now when Denon A1H and Marantz AV10 become more widely adopted that will be a video I would look forward to since they can utilize 13.4 auro 3D and 9.4.6 atmos switchable within the units!

@ealanosborne 11 ай бұрын

Once I can afford those AVRs to review (or Sound United thinks my channel is big enough to send me out units like that, haha), then YES! I’d love to do a video like that!

@leojuninocencio Жыл бұрын

Thanks it’s very informative.

@psyphonyxaudio 2 жыл бұрын

BLESS you for a short splash screen intro. =)

@ealanosborne 2 жыл бұрын

For reals! When I see an intro that’s 15-30 seconds long, I’m thinking, “just get to the video already!” 😄

@psyphonyxaudio 2 жыл бұрын

@@ealanosborne - Lead by example! Love it. As a person with limited attention and no patience.. Either be funny.. or get to the point =) I enjoy both of your qualities. I watched the video.. it's pretty useful as a rewatch for people setting up .. trying to configure. I didn't need it ..but i watch to support anyways =) .. I have the x6700H set with 11 speakers . 7.1.4 - ( power user status / specialist.. lol ) cheers!

@craigosterberg5045 2 жыл бұрын

Thanks for the video

@iyona14granturismogt6gtspo7 Жыл бұрын

I just checked and my Denon 4500 has Top Surround! Thank you! All this time I thought I needed 13.1 pre amp!

@ealanosborne Жыл бұрын

Hooray! 🎉

@stevewithf5847 2 жыл бұрын

At 3:21 min -Layout Front Height Surround Height there is only 5.1.2 with Dolby Atmos possible.Switch to rear Heights to get full Dolby Atmos support with 4Heights on all 3D Soundformats.

@godsdice473 Жыл бұрын

This information has a nutritional value of 9

@ealanosborne Жыл бұрын

Thanks! 🎉

@glengatt3941 2 жыл бұрын

My avr let's me pre amp the same as you showed or fronts or back heights, the first 4 speakers connection or the last 4,or all

@chodson65 Жыл бұрын

Can you put two speakers on one channel and place them in the middle of the TV screen and the other on the opposite side for VOG. I can't put VOG on the ceiling.

@panchomaresaltorf1111 2 жыл бұрын

from Auro 3D Fan Group International (EN)

@mauriciob8260 Жыл бұрын

Great video as always , I have the denon X4400H built in Auro 3D , the only downside for me this format don't use the surround back channels and for me some important effects pass over this channels , I just found that DTS Neural : X do a pretty good job using all the channel on my configuration including the surround back channel . I still need to figurate out how to install a VOG channel in my ceiling because is very complicate the way my ceiling is built

@ealanosborne Жыл бұрын

Thanks for watching! And good luck with the VOG speaker!

@paulk9534 4 ай бұрын

@@ealanosbornehi does vog channel take all low mids and highs? Can it run without side heights? Because its on sub 2 pin im think8ng ots only a sub signal 🤔

@ealanosborne 4 ай бұрын

@@paulk9534Yeah, since it's coming out of one of the sub pre outs, it'll need to be powered by an external amp. And yes, as far as I know, the signal sent to the VOG in an Auro 3D setup should contain full bandwidth audio, so it'll just depend on your VOG speaker's frequency response how deep the low frequencies will get.

@sirishpyata0910 3 ай бұрын

Very well explained. QQ: i have Denon 6700H, looking for 10.1 Auro 3D setup. Do i need an external amplifier for VOG?

@ealanosborne 3 ай бұрын

No, it looks like you would just need to plug it into Height 3 Left for VOG. 👇 manuals.denon.com/AVRX6700H/NA/EN/DRDZSYrjomlmpo.php#

@lithoman1130 Жыл бұрын

Marantz cinema 50 has 4 sub outs I am running 2 subs but with the extra 2 outs can i use one of the remaining for the God channel along with an amp ? Also, is the god channel directly above the main seating or centered between the other 4 ceiling speakers?

@ealanosborne Жыл бұрын

The new Cinema 50 allocates the Voice of God differently than their past AVRs. So you no longer have to use a subwoofer output to power it. Just search “Cinema 50 Amp Assign” and you’ll see the updated way to pull off Auro 3D setups. And you want to put the voice of god right above your listening position. 👍

@AexoeroV 2 жыл бұрын

Hey Elan, you are a good KZfaqr, you explain everything slowly and good! I have a question, what about the layouts when using 5 ceiling speakers? Can i set on a Denon X4700H to have two top middle channels plus the voice of god and two front heights or i need to have the exact layout like in this video(front height and rear plus VOG ) ?

@ealanosborne 2 жыл бұрын

Yes, it needs to be like this, where the height channels are labeled as "front height and rear height" instead of top height. "Top" in Denon's software automatically assumes it's an in-ceiling speaker, as opposed to a speaker that's been mounted. But that's just labeling. You could technically have speakers that are roughly placed where "top middle" speakers would be, and then in the software still label them as "rear height," just so Auro 3D can be recognized by the software. It's just a matter of minor details that you can slightly alter to your liking. Make sense? :)

@AexoeroV 2 жыл бұрын

@@ealanosborne Thanks for the info, yes it totally make sense. I thought i can set a layout like in the image from the link bellow, two top middle plus top surround(voice of god) and two height fronts and then from speaker configuration to disable the rear heights. Picture with the layout: i.imgur.com/NjKXQAX.jpg

@ealanosborne 2 жыл бұрын

@@AexoeroV No, it looks like the assign mode is set to 13.1, so that immediately tells me that photo is most likely from an x6700h which can process a total of 13 channels. The x4700h can only process a total of 11 channels.

@AexoeroV 2 жыл бұрын

@@ealanosborne no, the image it's from a pre/pro 8805 from Marantz, i have found a video about the Denon X6700H with the layouts and it doesn't seem to have this configuration either. I initially thought that if the X4700H can do 11 channels i could set up something like 5.1.5 for Atmos/DTS X/Auro 3D like i mentioned, two top middle channels, the voice of god and two front heights.

@ealanosborne 2 жыл бұрын

@@AexoeroV Oh okay, yeah the 8805 can do that as well. And yes, a 5.1.5 in the X4700h is technically a 10.1 Auro 3D setup. That’s just how Auro labels its configurations.

@tiyo1758 2 жыл бұрын

I have the Marantz 7015 as well. I’m utilizing all my base channels with the Emotiva XPA 7, but need to use the Marantz receiver just for my two front heights. Can’t seem to configure the Marantz to pre-amp the base while using only the receiver for the front heights until I can get another amplifier. Any suggestions?

@ealanosborne 2 жыл бұрын

Amp assign with 11.1, set Floor to 5CH + SB, height to 2Ch (front or top, whichever you have) and pre out set to FRONT. All 7 bed layer channels will be ready for external amplification that way. Then you can use internal amps for your heights. Make sense? 😃

@tiyo1758 2 жыл бұрын

Got it, Thanks. What was throwing me off was the software side of things being greyed out that you would think would be lit up other than the two front preouts. Thanks for your help.

@ealanosborne 2 жыл бұрын

@@tiyo1758 You're welcome!

@javierm9964 6 ай бұрын

Hello, I just watched your video, I find it very interesting. How would the Maranzt be configured if I have a 5-channel amplification stage. All the best

@ealanosborne 6 ай бұрын

Which model Marantz, since the steps involved depend on how new or old your AVR is… 🙌

@russellthetaipan 2 жыл бұрын

Hi. Could you tell me the name of the interconnects you are using? Thank you. Nice video.

@ealanosborne 2 жыл бұрын

Aperion Audio Braided Mono RCA Cable - www.aperionaudio.com/collections/speaker-wire-cables/products/aperion-audio-rca-audio-stereo-subwoofer-cable-mono-single?ref=xgnDvScPYS9H3

@russellthetaipan 2 жыл бұрын

@@ealanosborne Thank you!

@mikeortiz2139 2 жыл бұрын

Hey Ealan, about the Presets, on this AVR , say I setup a 7.1 bedlayer, and 4 heights, front and side surrounds. Could preset one be set to Auro 9.1 and Preset two be set to 7.1.2?

@ealanosborne 2 жыл бұрын

Yeah, I don’t see why not! That’s a good point…I need to make a video about presets. Thanks for the reminder! 😁🤘

@mikeortiz2139 2 жыл бұрын

@@ealanosborne yeah I'm confused on presets and how it affects Room Correction. I see a lot of people with speaker switch selectors. What I'm planning on doing is try to rig up some height brackets to move speakers into different locations based on layout. It's in progress.

@JonWickBoomStik Жыл бұрын

With a larger room, how would you setup say 4 voice of god speakers? Looking at setting up 13.2 auro 3d and atmos 9.2.4 setup? From what I've been learning seems auro 3d has the better up mixing or at least more coming out of those height speakers. Also looking at the Acram receivers like the AVR20 with external amp.

@ealanosborne Жыл бұрын

A larger room meaning multiple rows of seats? Because then I'd maybe have a voice of god for each row. It kind of defeats the purpose if you have a bunch of VOG's in/on your ceiling. 🤷‍♂

@JonWickBoomStik Жыл бұрын

@@ealanosborne yes 2-3 rows about 26' x 14' for the size room. That makes sense one speaker per row for VOG

@ealanosborne Жыл бұрын

@@JonWickBoomStik Wow, that’s HUGE! But yeah, one for each row should do the trick. 😁🤘

@EveryRandomThing Жыл бұрын

Ealan Osborne why wouldn't you use the 3 channel amp for the most important channels L,R, and C? Can you configure the receiver to use the preamp for those 3 channels?

@ealanosborne Жыл бұрын

Not for an Auro 3D specific configuration, no, unless you had ALL your speakers being powered externally. At least that's the limitation with this generation of Denon or Marantz AVRs (2020 models) since you have to use one of the subwoofer preouts to power the voice of god channel. The new series (x3800h, Cinema 50, etc) route the voice of god differently, so I believe you could use a 3-channel amp to power your LCR and use one of the internal amps to power the voice of god channel.

@04GEEDOGG Жыл бұрын

I just purchased a Denon X3800H AVR to try out the Auro 3D and I was looking under the sound/parameters options and I do not have the auro-matic options to adjust the levels or strength. Is this only available for there upper tier AVRs? The X3800H has Auro 3D but no way to tweak it.

@ealanosborne Жыл бұрын

Huh…I’m not entirely sure. I can ask around.

@04GEEDOGG Жыл бұрын

@ealanosborne I found the problem you have to have Auro 3D enabled in order to see the auro-matic 3D preset and strength options under the surround parameter options. THANKS 😊

@ThePenguin-rn1lo Жыл бұрын

Cool video, but Auro 3D is basically non-existent here in the US. Really seems we’re lucky enough that when older movies are upgraded from blu-ray to 4K that we even get them upgraded up to Dolby Atmos or DTS-X as they sadly remain in their DTS-HD audio format (Predator, Terminator 2, upcoming Poltergeist, etc…) Realizing this, I opted to go with a 9.3.4 setup having two front high/wides with two larger subwoofers on each side of the front stage and a third smaller subwoofer placed at rear near the middle. During full use, with everything full blast, will all 3 subwoofers run. Then after hours on a late night movie, I’ll only use the little subwoofer in the back. Now determining if Dolby Atmos is better than DTS-X, or vice versa, is the lingering question I have. Would that make a great video if you haven’t already addressed this yet? Atmos vs X ?

@ealanosborne Жыл бұрын

Yeah, that’s on the list (comparing Atmos and DTS:X) now that I have a proper theater to test it in. 🤘

@Foreverjazzfan Жыл бұрын

Good sir, I have a crazy question about a possible substitute for your voice of God 1 speaker in the 10.1 setup. I have the same AVR and have all Klipsch reference speakers. I am currently running a 5.2.4 setup with front heights, surround heights and rear surrounds. I am not using the integrated Dolby atmos speakers in my RP26FA towers. Could I use my 2 channel amp and power those atmos speakers which bounce off the ceiling and down on my head for the voice of God channel? Is that a crazy thought or what?

@ealanosborne Жыл бұрын

When it comes to configurations, there’s no wrong answer if it sounds good to you! 🤘 Since VOG is only one channel, though, you’d have to get an RCA splitter to connect both of your upward firing speaker to a 2-channel ext amp. But I’d say go for it! There’s so much room for science and experimentation within home theater, my friend. 😁🎉

@monk1100 Жыл бұрын

You'd need a hall for that set up ?

@P-LOWN1997 2 жыл бұрын

i have a 7,2,4 setup and I was wondering if i can put my front left front right and center channel into pre amp mode since i have a emotiva xpa3 gen 3 powering the front 3. It only shows in the amp assignment that i can put in the 7,2,4 setup but no pre amp for the front stage

@ealanosborne 2 жыл бұрын

Yeah, there’s no specific assignment for the LCR to be powered externally. Just choose 11.1 Amp Assign, Floor to 5CH + SB, then for the pre outs, select Front (then the word PRE will appear on each front speaker, and the center channel pre out will just be automatically ready for external amplification - no need to assign the center). Make sense? 😃

@P-LOWN1997 2 жыл бұрын

@@ealanosborne ok thank you i appreciate your response!🙏

@auburn2031 2 жыл бұрын

When you use side surround speaker setup you get no sound when you use Atmos. In order to switch back and forth between Atmos and Auro set receiver to front height and rear height. Surround height has no sound coming out when set on Atmos even though it says Atmos DTS and Auro.

@auburn2031 2 жыл бұрын

Set receiver to front height and rear height speakers then you can get Auro 3D and Atmos sound by pushing the movie button on the remote to toggle back and forth. Try it out! P.S. make sure your height speakers are around 30 degrees to the front and back of you Dolby also uses these settings now.

@prczyzew Жыл бұрын

@@auburn2031 How does side vs rear height avr settings affect actual auro3d playback? Any difference?

@AntonioGarcia-xk6jd 2 жыл бұрын

Where do you purchase your RCA cables from??? Please post a link...

@ealanosborne 2 жыл бұрын

There’s a link in the description! Aperion Audio braided RCA cables. 🤘

@carmineDeG Жыл бұрын

Hi I wanted an info I have a denon 3700 but if I wanted to add Auro 3D with an external amp or do an update how can I do it??

@ealanosborne Жыл бұрын

Unfortunately you can't with the 3700. It's not Auro 3D ready, so there is no update to add it later. But the new x3800h that will be coming out next year will support Auro 3D.

@carmineDeG Жыл бұрын

Ok but it doesn’t make much sense this Auro 3d I don’t see movies so I don’t mind changing the amplifier in case in many years some other more beautiful coding comes out to be worth it already having L atmos! ??

@kunalkarautiya8244 2 жыл бұрын

Hey Ealan, I wanted to ask you what are your opinions on Dolby Atmos Height Virtualization is it worth it. Coz I'm on a very strict budget and what the options in market with this feature. Lots of love from India

@ealanosborne 2 жыл бұрын

It’s pretty good! Sometimes objects or certain sounds might come through a little too loud or weird, just because the source is 5.1 or 7.1, but that’s not too often. It’s pretty fun to have height speakers to add to the grand scale of audio around you. 😁🤘

@kunalkarautiya8244 2 жыл бұрын

@@ealanosborne thank you so much Ealan. It would be a bit more helpful if you could suggest some systems with this capability ❤️

@cruzgallegos5071 2 жыл бұрын

@@kunalkarautiya8244 My first receiver was the Denon AVR-X2600, it had height virtualization, that seemed to work better using bipole speakers for the side and rear channels. The Atmos like sound is nice and works nice, realistically, doesn’t come close to actual ceiling speakers. I think this receiver runs around the $400 US ?

@ealanosborne 2 жыл бұрын

@@kunalkarautiya8244 Almost budget level 7 channel receivers have Atmos height virtualization, like the Yamaha RX-V6A and the Denon S760H. But as the comment above says, nothing beats actual speakers up above. But virtualization is a good start on a tight budget. 👍

@bambampiewpiew540 9 ай бұрын

Great video thanks 👍 . Please help us to connect two center channels . ✌️

@anicetonagaoka9778 Жыл бұрын

Can i use the normal receiver and the pre out simultaneously?

@ealanosborne Жыл бұрын

Yes, you can have a combo using internal amps and pre outs to external amps. But this AVR in particular can still only process up to 11 channels and 2 subwoofers. 👍

@sanjeefonseka103 7 ай бұрын

@@ealanosborne Can Denon 3800H process 7 bed layer speakers and 4 heights + one top VOG via second subwoofer out with external amp since It has four subwoofer outs ?

@ealanosborne 7 ай бұрын

@@sanjeefonseka103 It looks like you can't, unfortunately. Must be a software limitation. Check out the link below and scroll down to the 11.1 Auro 3D section. manuals.denon.com/AVRX3800H/NA/EN/DRDZSYrjomlmpo.php

@keepitshema Жыл бұрын

So Auro3D uses VOG and what if we choose instead top middle(two speakers-like left and right top middle)? Auro 3D still gone use them or it would be only used by atmos?

@ealanosborne Жыл бұрын

Well, top middle would imply 6 height speakers, correct? If that's the case, only the newest Denon and Marantz models (X3800H, X4800H, Cinema 50, etc) support 6 height speakers, and I do believe Auro 3D would still be supported with 2 Top Middle speakers. But I could be mistaken...

@keepitshema Жыл бұрын

@@ealanosborne thanks, but you’re late-I already drilled a hole in my ceiling for VOG 😅 tomorrow expecting a speaker arrive. eventually I will add centre height later. Did I wrong? Better would be top middle? Maybe avr would do them mono and imitate a phantom VOG? Yup, after our last conversation I went with Marantz sr8015 so plenty combination to do🤣

@ealanosborne Жыл бұрын

@@keepitshema Oh dang! Well yeah, the SR8015 will give you plenty of wiggle room, for sure! 😎🤘

@nomorepictures7673 2 жыл бұрын

Why can’t you use more pre outs if they are Available? If you gain a subwoofer two pre out for top surround. Why can’t you keep the back surrounds?

@ealanosborne 2 жыл бұрын

Just depends on the limitations of the software and processing of your receiver. I WISH every pre out could be assigned to whatever you wanted, but that’s usually limited to the real expensive preamps. Go figure.

@nomorepictures7673 2 жыл бұрын

So I have the denon 4700, after hooking up 7.2.4 all on pre amp mode and subs daisy chained or y spitter, the subwoofer 2 pre out is available and it wont work due to the software? Looks like it can easily be fixed through a firmware.

@randelldavis578 Жыл бұрын

Hi Ealan, I have a question about the auddessey editor app that I hope you can answer for me. I have a marantz sr 6015 running a 5.1.4 setup. My sub is the SVS pb 3000 and my room is 12x12x9. I've read that you'd have to run a minidsp and Rew before using the editor app and I also read one article that say if you have only one Sub that you don't have to run minidsp and Rew. I'm new to the hobby and not sure if I do or don't. I've already gotten the editor app and almost confident to apply it but with the DSP and the Rew I think that I'll make things worse and just go back to using xt32. Thanks for your channel I subscribed about six months ago.

@ealanosborne Жыл бұрын

Typically you’d want to run REW with a MiniDSP if you have more than one subwoofer. MiniDSP would help really dial in those subs, time alignment, etc, so that they work well together, instead of fight each other in your listening space. You should be fine running Audyssey. But I almost always go back in and make a few manual adjustments after Audyssey, because it’s never 100% accurate with all its calculations. 😄

@randelldavis578 Жыл бұрын

Thanks, it really means a lot that you answered and quickly I might add. Now I know what to do, thanks. Also, after watching the content you dropped today I decided that I'm gonna support your channel $$. How do I send money with out the scanners trying to chime in?

@randelldavis578 Жыл бұрын

Scammers

@ealanosborne Жыл бұрын

@@randelldavis578 Hey thanks! I really appreciate that! And as far as scammers, I’m not sure. I assume KZfaq has its stuff figured out when it comes to contributing to memberships? 🤷‍♂️

@railerswim 2 жыл бұрын

Should note this isn't available on all Denon and Marantz receivers. With denon you need the x4700h and up. The x3700h does not have auro 3d

@balajis7719 2 жыл бұрын

I have 4400h denon. Even that's having Auro 3d. When you select front or rear height channels, auro 3d will be enabled.

@cigaretteman5716 Жыл бұрын

How do you power all them Amplifier’s with AC ..

@ealanosborne Жыл бұрын

Very…carefully?

@cigaretteman5716 Жыл бұрын

Do you have a video on how all these amplifier’s get plugged into a standard wall socket I have 2 Panamax M5300 connected to my wall socket and each one only has 2 high current options so how would a fifth amp work

@ealanosborne Жыл бұрын

@@cigaretteman5716 I'm not sure. Maybe have the home theater on its own dedicated circuit with a little more amps than the rest of the house? When I built my testing theater, I split the room - one half on one 20 amp circuit, and the other on a separate 20 amp circuit. So the 2 outlets behind the TV are on different circuits. I overcompensated, so that I never had to worry about too much power being used by any circuit. But I know not everyone has the luxury of starting from scratch like that. 🤷‍♂

@cigaretteman5716 Жыл бұрын

I appreciate the advice..thanks bud 👍

@iansteventon4221 3 ай бұрын

So ive just bought twister auro 3d blu ray , denon 6700h. 5.2.4 , avr says auro supported , but i only get the dts 5.1. Is this because i have no vog speaker? Atmos disc works fine , auro disc only 5.1. ?

@ealanosborne 3 ай бұрын

I believe the X6700H is a bit finicky when it comes to an Auro 3D supported layout. Double check your amp assign section in the setup menu to make sure your height speakers are assigned as “front height left/right (FHL/FHR),” and “surround height left/right (SHL/SHR).” If you have heights assigned as “Top height left/right,” technically the AVR won’t recognize it as Auro supported. Strange, I know. In the link below, scroll down to the section labeled “Example connection for the Auro 3D 9.1 channel system” and you’ll see what I mean. If that’s not the issue, then I’m at a loss. 🤷‍♂️ manuals.denon.com/AVRX6700H/NA/EN/DRDZSYeosolrjl.php#

@iansteventon4221 3 ай бұрын

Thank you mate, I have it at rear height ( no side heights) so that's maybe the problem. ( although avr says auro supported) I'll try and change configuration tonight. Appreciate your help 👌

@iansteventon4221 3 ай бұрын

@@ealanosborne YOU BEAUTY ! YOU ARE THE MAN ! THE BOOK OF EALAN ! THE HOLY BIBLE FOR AUDIO 🔉! thank you! Auro 3d is now GO GO GO ! changed rear height to side heights as you said and BINGO 🔊. 👌

@ealanosborne 3 ай бұрын

@@iansteventon4221 WOOHOO! 🎉 Man, I wasn’t 100% sure so I’m so glad it worked! 😄🤘 Enjoy Twister in all its Auro glory!

@carmineDeG Жыл бұрын

Hi can you help me please I have a denon 3800 and I would like to connect 12 cases to also make auro 3D? How can I do that? What connection do I make!? Can you let me know, thank you very much

@ealanosborne Жыл бұрын

12 cases? I’m assuming that was a typo…? Not sure what you mean there. The Denon 3800h can only handle a 11.1 Auro configuration since it can only process up to 11 channels with the aid of an external amp. Click on the link below and scroll down to where it says “Example layout for Auro 3D 11.1 channel System.” 👇 manuals.denon.com/AVCX3800H/EU/EN/DRDZSYrjomlmpo.php

@carmineDeG Жыл бұрын

@@ealanosborne ok, one question se compro emotiva basx a2 posso alternare le casse per sfruttare AURO 3D??

@carmineDeG Жыл бұрын

Ok it’s a question if I buy emotional basx a2 can I alternate the speakers and can I also take advantage of auro 3d??

@ealanosborne Жыл бұрын

@@carmineDeG Yes that’s correct

@carmineDeG Жыл бұрын

One last thing but how come I don’t see AURO 3D in 3800 in the encodings, and I only see AURO 2D how do I select it ???

@iyona14granturismogt6gtspo7 Жыл бұрын

Shouldn't we be able to power voice of God channel with Unused rear channel speaker outputs???

@ealanosborne Жыл бұрын

Not with certain Denon or Marantz AVRs. It’s just a matter of how they setup the software to process voice of god. The newer models are more flexible, from what I’ve seen in the user’s manual, though (x3800, x4800, Cinema50, etc)

@iyona14granturismogt6gtspo7 Жыл бұрын

@@ealanosborne incredibly comprehensive video, no one has done,thanks for the effort.

@ealanosborne Жыл бұрын

@@iyona14granturismogt6gtspo7 Thanks for the kind words! Truly appreciated! 🤘

@roberthyde7102 Жыл бұрын

Who make your RCA, cable

@ealanosborne Жыл бұрын

Here you go! 👇👇 Aperion Audio Braided Mono RCA Cable - www.aperionaudio.com/collections/speaker-wire-cables/products/aperion-audio-rca-audio-stereo-subwoofer-cable-mono-single?ref=xgnDvScPYS9H3

@roberthyde7102 Жыл бұрын

Ok thanks you

@WayneGrant-bl2pq Жыл бұрын

Hi Ealan, great information, I am a former Atmos listener, I read something about Auro 3D back in 2016 on a site somewhere. I was very intrigued and I took a chance and changed my speaker configuration, bought the $200 upgrade for my Marantz SR7009 thinking if it was not what they said I would just roll up my sleeves and go back to the Atmos setup. Here it is in 2023 and I still have Auro 3D and loving it! I found that Atmos can only work with Atmos encoded material, while Auro 3D plays everything in immersive sound, even my Atmos encoded discs sound great. I like that `it puts you in the middle of the action. I have a question for you about your setup pertaining to your height speaker downward angles. Did you find an optimal angle for your setup? I am preparing to order some Klipsch Bookshelf speakers for my heights and did you find it better to have your heights pointing directly down into the listening area or pointing down slightly above your head? I presently have a 14x16 room, I modified my inwall speakers to accommodate the front height at 7 degrees and the back surround heights at 20 degrees down. It sounds great like this, but I am thinking of going directly into the listing area with my new speakers. What do you think about that?

@cruzgallegos5071 2 жыл бұрын

It's too bad about Auro 3D going bust, next is IMAX enhanced. I still own 4 of the 10 IMAX titles available on 4k.

@ealanosborne 2 жыл бұрын

Eh…we’ll see. Auro is going to make some changes, but filing for bankruptcy is usually a strategic move. Interested to see what they do. Hopefully bring the price of licensing it down, so Auro can be included on less expensive receivers. 🤞

@doublet147 2 жыл бұрын

@@ealanosborne Unfortunately, I think that's wishful thinking. Dolby already has a foothold. Then there is DTS & IMAX. Europe kept Auro somewhat alive in the past.

@aussierob7177 2 жыл бұрын

Instead of multiple speakers all around the room I can achieve a real 3 D sound stage with my 2 front stereo speakers using cross talk cancellation.

@hypnoz7871 2 жыл бұрын

lol, you'll never achieve the scale of an Auro 3D with crosstalk.

@kuronekosan2830 Жыл бұрын

How do you do that man ? I wanna achieve a 3D soundstage with only my fronts Do you use dsp ?

@MotorMaus01 Жыл бұрын

Even in large you can put crossover! Put it in lfe+main. Large still play full range but your lfe jump in with the desired crossover(dubbel bass) Don’t forget your av cant handle that much speaker in large

@GurcharanjeetSingh 10 ай бұрын

isn't this setup more like 5.1.5? 🤔

@ealanosborne 10 ай бұрын

Yes, but Auro 3D can call it whatever they want, I guess... 😄

@GurcharanjeetSingh 10 ай бұрын

@@ealanosborne 😅

@georgepitris8858 2 жыл бұрын

What next 50.3 channels the idiocy continues......🤣

@Rockovissi 2 жыл бұрын

Sometimes it all feels like this: kzfaq.info/get/bejne/l96IpdZmmr6dm3k.html

@doublet147 2 жыл бұрын

Auro 3D is kinda useless except for some music upmixing. With next-to-none native Auro formats for movie or music, it would be a waste of time to design one's theater speakers physically for an Auro format.

@mariod8405 7 ай бұрын

Seems you have no clue about Auro3 d and the capability of the Auromatic upmixer for movies

@doublet147 7 ай бұрын

@@mariod8405 okay

@bujoun76 2 жыл бұрын

Sorry folks but Auro3D is dead! The company has already filed for bankruptcy.

@fotophotographer 2 жыл бұрын

True, but rumour has it that Auro3D upmixing is excellent and the speaker config providing a very immersive sound experience. So while movies might not be mixing Auro3D any more the processing capability and the speaker setup could still add a lot of value.

@ealanosborne 2 жыл бұрын

For a lot of corporations, filing for bankruptcy is a strategic move, not the end of the world. www.ecoustics.com/news/auro-technologies-bankruptcy/

@railerswim 2 жыл бұрын

Auro may be forced to innovate or die now. They may do a lot of restructuring (layoffs, department closures, etc). It may lead to re-evaluation of licensing costs, and it will force them to get more sales. So you may end up seeing more auditoriums with Auro 3d, and maybe even more consumer level equipement with the ability to process auro3d content.

@ealanosborne 2 жыл бұрын

@@railerswim It would be nice to see Auro 3D in more inexpensive Denon/Marantz receivers - at the very least down to the X3700H/SR6015 level, or whatever the next generation might be (X3800/SR6016, etc)

@mariod8405 7 ай бұрын

They still record stuff in Auro3D