Thank you for making this video. This worked for me when I was struggling to get the nut off.
@BrunoWoodwoRx2 ай бұрын
Thanks brother. Just used this technique. Appreciate the video!
@kaioburns17 күн бұрын
Thank you. Smaller stable saw I used a long clamp arm.
@allendesomer2 жыл бұрын
Since the handle end of my wrenches don't have openings to insert anything into I tried to squeeze them toward each other with a large wood clamp, but they just bent until there was no more clamping force to use. Luckily I have a good solid crescent wrench, some thick lumber and a very heavy carpentry hammer. I sandwiched one board between the nut wrench and a cement wall, I lowered the blade just low enough to engage another board in front of the blade, and after a few hard blows the nut finally came free. My saw is new, so the over-tightening was from the factory. I'm glad the extra money I spent on a new blade didn't go to waste. Thanks for getting me thinking.
@SbentonMft3 жыл бұрын
You made my day. I was getting pretty frustrated and your solution worked like a charm. Thank you so much.
@CombsDesign3 жыл бұрын
I am so glad I could help! I was in your same shoes when I came up with this idea and made a video on it!
@sexxxyDDDiva2 жыл бұрын
@@CombsDesign u77ìù
@OnefinityCNC8 ай бұрын
This helped us out today! Thanks for the tip!
@alimaleki2173 жыл бұрын
Thanks for this tip; really came in handy! I didn't have a pipe clamp but a wooden dowel worked.
@CombsDesign3 жыл бұрын
Glad it helped! Really anything that will help you get some leverage will do!
@dscritter6142 жыл бұрын
Will make my 1st blade chg tomorrow. I was thinking 2 myself, I bet it will b hard 2 get off. Better check youtube 4 stuck blade videos. Thx so much 4 sharing. I have a broom handle sitting nearby. Brilliant!
@christene503 Жыл бұрын
Thank you! You made my day. This work great for me and all I need was a broom handle.
@khalidnazim4 жыл бұрын
Excellent - i just used this trick to remove a stuck arbor nut. Thank you so much
@CombsDesign4 жыл бұрын
Excellent!
@tjshelton47052 жыл бұрын
Thanks! I was getting frustrated. Worked like a charm!
@drahma2 жыл бұрын
Totally worked! Thank you. I was too lazy to grab my pipe clamp so I used my least favorite bar clamp (I'm looking at you, Lil Slippy) but it still did the job.
@CombsDesign2 жыл бұрын
I certainly have a few bar clamps that like to slip. Glad the video was helpful!
@KurtGuenther5 ай бұрын
Saved my afternoon. Great tip
@royhowze4023 Жыл бұрын
Very good instruction, and very smart. Thanks.
@rainapple614 жыл бұрын
Very smart! Thanks for sharing the tip!
@CombsDesign4 жыл бұрын
Glad it was helpful!
@seanshaw4362 жыл бұрын
Thank you my blade is bent after lending it to a buddy and it did really help me out
@CombsDesign2 жыл бұрын
Your buddy better buy you a new blade! Also… how do you bend a table saw blade??
@mcssewell3 жыл бұрын
Thanks - worked like a charm and didn't have a pipe like you showed - only a metal thick stake for horseshoes.
@CombsDesign3 жыл бұрын
Thanks! Anything to get some leverage and get the initial push to get the nut turning will do it!
@stevejazzband Жыл бұрын
No way... Let me see. Oh my god you are a genius.
@stewartsstewart10892 жыл бұрын
what type of wrenches are those again. I need two! Your idea is fantastic!!!!
@CombsDesign2 жыл бұрын
They are the ones that came with the saw, I don’t know if you can buy them individually.
@michebre2 жыл бұрын
Thanks will try this.
@felixreali710129 күн бұрын
I tried this and the wrench that came with my little DW745 actually expanded....I think I need a stronger wrench!!!🙄🙄 (PS: I have also tried adding WD40 but no luck; I might try my heatgun next...other than that, I think I might buy a new table saw 😅)
@technofeeliak8 ай бұрын
What do you do then if it won't come free?
@tomrauterkus3541 Жыл бұрын
Where do you get those arbor wrenches? I lost mine.
@MAGA_Patriot20242 жыл бұрын
Great video, but my problem is a little different. I was able to remove the arbor nut, but behind it is a flange. THAT is what's keeping the blade stuck, and unfortunately with the nut off I have nothing to grip with the 2nd wrench. Any ideas on what I could try?
@CombsDesign2 жыл бұрын
Hmmm, potentially a heat gun and some light hammer taps. Changing temps can get things moving. If the table saw is in a hot environment you could also try cooling the stuck piece, there is a product plumbers and mechanics use to rapidly cool something to get it to move, it comes in a aerosol spray can at the home store. Good luck!!
@daimeonwilmot74344 жыл бұрын
This is very smart but I have 1 question, what about when u have 1 nut bc the table saw is belt fed
@daimeonwilmot74344 жыл бұрын
Also it's a small tablesaw
@CombsDesign4 жыл бұрын
Thanks for checking out the video. Unfortunately I do not know enough about belt fed saws to give you a good answer.
@daimeonwilmot74344 жыл бұрын
That's alright, I think I may have found something that worked anyways, thanks for the help!