GE WASHER DRYER COMBO DIY LINT FILTER FIX - STOP LINT BUILDUP ON GE ULTRAFAST PROFILE COMBO

No video

GE WASHER DRYER COMBO DIY LINT FILTER FIX - STOP LINT BUILDUP ON GE ULTRAFAST PROFILE COMBO

Рет қаралды 2,349

Күн бұрын

The GE Profile Ultrafast Washer / Dryer 2-in-1 combo unit has a big design flaw that allows lint to bypass the lint filter and build up on the fins of the heat exchanger / compressor. Over time, the combo will fail to dry properly due to lint on the heat pump.
The lint filter top, rear, and bottom ridges do not make a good seal with the filter housing. There are airgaps along these sides of the filter, which enable lint to bypass the filter and get trapped along the heat pump fins.
My fix for this is to tape some rubber foam self-sticking weatherseal on the filter to close up those gaps. I am using foam that is 3/8 wide x 3/16 thick.
The adhesive has been holding up fairly well, so i'm not concerned about it peeling off.
www.homedepot....
It is definitely blocking a lot of the lint, compared to an un-modded filter.
I think GE should revise the filter housing design and ship out replacements to every combo owner. The current design is unacceptable and guarantees that the unit will fail long term.
There's a popular video by Ben's Appliances, where he apply silicone to the inside of the filter. I do not believe this addresses the main issue of the air gap.

Пікірлер: 11

@Ozzie4Para 5 күн бұрын

I did this to mine and it really does work. I ordered the same stuff from Amazon like he did. Only difference is I only did the top and rear part of the filter housing. I tried doing all three sides but there's too much friction taking the filter in and out and I feel like that friction will begin to wear the insulation out in no time. Doing just the top and the rear works great. I will say this trick has eliminated probably 98% of the lint that was being bypassed on to the coil. Its pretty rare I see any lint on my coil after this mod. The other suggestion I would say is to leave the filter out of the machine when the machine isn't being used. Otherwise I feel like the insulation will get compressed over time from the filter being constantly in the machine.

@fluxwood 5 күн бұрын

Ive seen people use pile weather seals, which has furry fibers instead of foam. It would have less friction and would accomplish the same thing, but i havent tried it out.

@gammerata 14 күн бұрын

Great video and insight. Any updates will be appreciated. I read you put two strips on the back but it's not in the video. so had one to the back and then wrap over all three sides, to include the back strip as u did? BTW was there a reason you ended up adding a second strip to the back?

@fluxwood 11 күн бұрын

Yeah I have one long strip covering the top/back/bottom, and a second strip for the back so that the width is completely covered. At 2:01, you can see that the rear of the compartment has a rectangular channel - I just wanted to fill it up because I saw lint building up over there.

@majestyk3337 2 ай бұрын

Back to the drawing board.

@DIGITAL-POST 29 күн бұрын

Heyo... Great video and fix! I noticed in you updated video, that you now how the back 1 inch form modified to be shorter and curved? Why is that and should we be doing it as well?

@fluxwood 29 күн бұрын

Not sure what youre asking… the foam goes all around the back. I actually added two strips in the back, side by side but its not in the video.

@rbyerly Ай бұрын

Is it safe to use the foam at high temperatures? I'm concerned it could catch fire.

@fluxwood Ай бұрын

I dont see a temperature rating for the one I used, but there hasnt been issues so far. The air going through the filter is very moist from the wash cycle.

@K.Solowoniuk Ай бұрын

How has this been working? How is the unit overall, I think it'd be nice to set a timer for 4am and have laundry ready to go before work. Lower power consumption and cheaper power too.

@fluxwood Ай бұрын

It's working fine - foam is still intact and heat exchanger fins are still clean. I like the combo alot, its definitely better than having two machines. You just have to be vigilant about cleaning the filter every time. I find that the lint is wet after a complete cycle - so you have to clean it off asap or else itll start to smell.