No video

Easy Golf Grip Removal with this Tip

  Рет қаралды 221,606

ELITE FIT GOLF / Mobile Clubmaker

ELITE FIT GOLF / Mobile Clubmaker

Күн бұрын

See how to easily remove golf grips with this simple tip. Be able to reuse your existing grips and save time and money.
Golfworks grip removal tool-
www.golfworks....
Check out Elite Fit Golf
/ elitefitgolf
Follow me on Instagram
@mobileclubmaker

Пікірлер: 189
@dunningkruger3774
@dunningkruger3774 4 ай бұрын
I've been blowing them off with air pressure. This is much SAFER- GREAT channel!
@johnschwartz1536
@johnschwartz1536 3 ай бұрын
I've been using acetone with a grip removal tool for years in removing golf grips without destroying them. Sometime, it wasn't easy! This time was the worse in trying to remove a paddle board putting grip. I could not get it to budge. I came across your video recommendation to use grip solvent which I did and it couldn't have been easier. After 25 years of struggling, I have now found a new method of removing golf grips! Many thanks to you, sir!!!!!
@jsant24
@jsant24 5 ай бұрын
That was the best method I have seen to remove the old grips.
@arthurmooney9482
@arthurmooney9482 11 ай бұрын
Super fast and clean grip removal. This is the best method I've seen yet. Thanks.
@thequestionsIaskmyself
@thequestionsIaskmyself 3 ай бұрын
Thanks for taking the time o make the video. I just put new grips on with ease.
@jaybales3160
@jaybales3160 Жыл бұрын
I do mine the same way with the exact tool. Good investment. Saved about 300 grips so far.
@hippocampulus7854
@hippocampulus7854 Жыл бұрын
A hacksaw blade works great for getting tape residue out of the grip -- the small teeth grab the tape without damaging the inside of the grip
@lancesedevie548
@lancesedevie548 11 ай бұрын
Worked super well. 6 putter grips in about 20 minutes. The flatcat grip was very stubborn but I got it. Thanks for tip with paper towel 👍
@joed9285
@joed9285 6 ай бұрын
Was going to ask if you can get pistol or other putting grips off. Want to save an original Cameron grip this is a great vid. Thanks for the comment.
@TimmerGfromBC
@TimmerGfromBC Ай бұрын
For those of you without a compressor, I purchased a meat marinating needle from Amazon for $12. I inject grip solvent down into the grip before inserting the removal tool and it works like a charm! Not sure why I thought of it, but it works!!
@michaelcone6968
@michaelcone6968 7 ай бұрын
I have the tool and it works great, but your technique is far better than I used. Thanks for sharing.
@bobsofia68
@bobsofia68 Жыл бұрын
I've done both methods of grip removal, bent coat hanger & $25 GolfWorks tool. The GolfWorks tool is so much faster. Recently switched all of my grips, GolfPride TV +4 mids, Driver down to PW, midsize TourVelvets on my wedges. For removal I put a folded rag inside a 2 gal. bucket on the floor, a bit more leverage for the longer clubs.
@beaston18
@beaston18 Жыл бұрын
Great vid. This is almost exactly how I remove grips. The Golfworks tool is well worth the 💰!
@spennce
@spennce Жыл бұрын
Best golf club repair tip channel on KZfaq! I like to put the club in a vice vertically with the handle down and move the removal tool around the grip. Have a drip pan underneath to catch solvent. Try your best to have the removal tool over the grip tape when first slide into the grip. Always love your videos and keep the great content coming!
@mitchd949
@mitchd949 Жыл бұрын
Great vid, simple technique. Sad to think that 2-3 grips really is pushing $25 USD these days! I remember as a kid getting Golf Pride "Victory Grips" for 89 cents each and re-gripped 1-2 times per year.
@Lamster66
@Lamster66 Жыл бұрын
Lol I remember years ago dropping a couple of clubs into the proshop before going out to the driving range and on returning charged £5 for 2 fitted golf pride tour wrap grips.Recently I dropped by the local Golf store and asked about a new Grips for my clubs and he said they're £2 a club But what he meant was that is the fee for fitting, them. The grips were £9each. Even the Fake ones on eBay are £3 each
@matt7iron
@matt7iron 11 ай бұрын
Shiett mang a supa stroke putta grip costs $45
@Lamster66
@Lamster66 11 ай бұрын
@@matt7iron And Fake SuperStroke off ebay is under $10 I just fitted one to a putter for someone TBH there isn't $35 difference.
@renmay3171
@renmay3171 Жыл бұрын
Love the technique! Was putting off buying a grip removal tool because I thought you just shoved it straight down. Did not think of the spinning.
@marvelmac2343
@marvelmac2343 Жыл бұрын
Awesome Tip 👍🏼 , I've Had that Tool For Grip Removal but Never used it 🤦🏻‍♂️, Much Easier Way for Grip Removal And Money Saving !!!
@Criscross292
@Criscross292 Жыл бұрын
As always, very informative. This will definitely speed up my next grip removal. 👍
@meazlesgolf3455
@meazlesgolf3455 Жыл бұрын
Yep - I agree. Until now, my grips became a sacrifice as it didn't even dawn on me that the grip could be removed intact. Thanks mate!
@davidjennings6937
@davidjennings6937 Жыл бұрын
I like that idea of the paper towel. I've always used a paint pan but the towel has to be easier. Thanks!
@pressuredup
@pressuredup Жыл бұрын
Dental syringes with the curved tip work great for getting the solvent under the grip and not spilling a bunch of it.
@mackerthewacker7822
@mackerthewacker7822 5 ай бұрын
Exactly what I do as well and the curved nozzle end means virtually no mess. 👍👍
@troyrambo6804
@troyrambo6804 Жыл бұрын
I've been looking for just this. This will save me $130.
@andymincer2127
@andymincer2127 Жыл бұрын
A friend used the air compressor method and employed a metal vacuum cleaner tube cut to length to keep grips from exploding. Worked well for him.
@mickb4691
@mickb4691 5 ай бұрын
I use that method too. In the time he did that 1 grip I could do 3. So quick and easy.
@scotto6120
@scotto6120 Жыл бұрын
Great video! Used this technique removing my grips, worked out well. Instead of the special grip removing tool I found an old barbecuing long handled spatula laying around to use. By removing the spatula flat part all was left was a small flat landing with rivet holes. Filing the hard edges to give it a hopefully non scratching end. Also bent the handle side bar to off set it away from the golf shaft.
@stratovani
@stratovani Жыл бұрын
I've got an older grip removal tool with a wooden handle that I bought from Golfsmith back in the 1990s, and I've been using this method to remove grips that I've wanted to keep, but I've had to do it in the kitchen sink. I like the paper towel method, think I'll try it next time.
@mikewilliams1479
@mikewilliams1479 Жыл бұрын
I like this method, tried it with the hanger and it works so fast.
@elliott3991
@elliott3991 4 ай бұрын
Thanks , have bladed for years, but not heated them before removal, just heated the tape after making easy to scrape off the shaft. Will now heat before also.
@davidgent188
@davidgent188 Жыл бұрын
I paid £45 for the same removal tool here in the UK! Worth it though if ya always experimenting with different grips…. 👍
@j.mccarthy3008
@j.mccarthy3008 2 ай бұрын
Interesting!!! I will have to try this. I started blowing grips on a few years ago to be able to switch grips easily. Not using solvent or tape. Works well for shorter clubs but grips move a bit on longer ones.
@hottytoddy1967
@hottytoddy1967 Ай бұрын
I've used naptha for years (was taught re-gripping using lighter fluid). Absolute best solvent, cheap, and if you catch excess in a drip pan reuse it.
@joshuahanson8543
@joshuahanson8543 8 ай бұрын
I’ve used a wire hanger for the last 3 or 4 years and it finally broke! I’m definitely getting one of these for it’s benefit of being more rigid. The wire hanger definitely bent a handful of tomes and caused some headache, so this seems well worth the buy! Love your videos! 🤙
@Rileyinfo9
@Rileyinfo9 3 ай бұрын
This is way better and safer than the old needle injected solvent and twist method.
@lsanchez841
@lsanchez841 27 күн бұрын
Great video. Think I'll try it but with an old small Tupperware bowl instead of a paper towel to save the solvent as long as it doesn't slide off the bench... Yes I'm cheap.
@e.g.flores2819
@e.g.flores2819 3 ай бұрын
Thank you so much, great tip, i did not know how to use my tool, i was trying to use it without the solvent.
@roger55es
@roger55es 3 ай бұрын
Excellent method to removing the grips Thanks
@danb.2605
@danb.2605 Жыл бұрын
Thank you. The trick is to spin it around. I have the similar remover but still had a hard time removing the grip because I just kept shoving it down instead of spinning it.
@shepardsmith3235
@shepardsmith3235 Ай бұрын
I have a gripping station and use the hooked knife to get the grip off. Its quicker BUT I think I will use the heat gun you have suggested which makes a whole lot of sense, first. So thanks for the tip. PS This is only half of the equation. You probably should have shown the viewers how to install the new grip too.
@EFGMC
@EFGMC Ай бұрын
I've got a bunch of regripping videos on my channel. Here is one of the newer ones. kzfaq.info/get/bejne/rb2clpOeurTdYXU.htmlsi=5ebdf3KxQELEcAGM
@shepardsmith3235
@shepardsmith3235 Ай бұрын
@@EFGMC Big thanks and will check this out. I have been doing this for a long time . The one thing that I would really like is an air compressor to blow the grips on and off but thats way too expensive. Again, Thanks.
@MrJohnnyb74
@MrJohnnyb74 2 ай бұрын
This is the method I use for removing grips. Keep the rag or paper towel handy for when you re-grip to catch the excess solvent from running down the shaft and onto the grip.
@billcox199
@billcox199 Жыл бұрын
The golfworks tool is the best I've used in 40 yrs. Don't push down too hard ,it can go through the end cap.
@guyhall6592
@guyhall6592 Жыл бұрын
Good stuff, thx. You’re good dude. Recently acquired several sets of clubs with OG leather grips. I know cra cra… Some in good shape just dry. Do you have any Ideas tricks of trade to restore/save all leather grips? Wilson staff & Top Flite, I love blades ✌️out
@luzzionz
@luzzionz Жыл бұрын
I completely concur with the removal tool, I made one from wire hanger it worked but it's nothing like the real deal, now here's my question I also have a tape scraper for graphite shafts now exactly how does one sharpen that bad boy! thanks in case you answer or do a tutorial .. enjoy your content.
@EFGMC
@EFGMC Жыл бұрын
Dremel tool
@CarnivoreDMD
@CarnivoreDMD 5 ай бұрын
A long thin flathead screwdriver & rubbing alcohol pretty much does it. I always use air compressor and usually remove tape altogether. Haven’t used tape in 20 years!
@petegalindez9961
@petegalindez9961 Жыл бұрын
Great stuff Gabe…I actually use a BBQ Skewer that has the identical shape as that without the offset…works well.
@creamabdul-jabbar6722
@creamabdul-jabbar6722 3 ай бұрын
Have 2 shafts. I'm cutting down my older steel driver shaft to experiment. Cutting it from 45 to 42.5 inches and adding 14g to the head with a jumbo max grip. But I'm getting anxious before the new grip comes in and want to go ahead with the process. Going short heavy regular flex steel shaft and a long light graphite stiff flex. I retired the regular about a year ago was too long. But I don't want to go cutting around on the graphite shaft. I'm hoping a little more weight shortened will be good for keeping me in the fairway. I average 275 off the tee. But even if my numbers drop to 260 with it I'd be happy
@jimmypickett2449
@jimmypickett2449 Жыл бұрын
I use a hacksaw blade to remove residue and smaller pieces of tape that I fumbled while removing the grip. It works the best in my opinion. I haven't tried a longer bolt tho. Yet but I will
@wickdghost3639
@wickdghost3639 6 ай бұрын
You can get that tool at harbor freight too, you would just have the sand the edges and put and little belt by the handle, it's the windshield removal tool 👍
@biggregg5
@biggregg5 Жыл бұрын
Hmmm....I did just learn something. I do the air compressor method, and it usually does the trick. However, I never thought of heating the grip. I bet that will help with the stubborn one.
@larryclausen8907
@larryclausen8907 Жыл бұрын
I use a small paint fill bottle to squeeze the solvent between the shaft and tool. Uses far less solvent and easier to pin point the solvent
@radman9219
@radman9219 6 ай бұрын
I use a 20 gauge shot gun bore cleaning brush. Pulls all of the old tape out if there is any left inside of a .60 grip. 20 gauge has an outside diameter of .615. I switched to a .410 gauge for a .58 grip. It a little to small but it still works.
@dunningkruger3774
@dunningkruger3774 6 ай бұрын
Bingo! I was actually thinking about the wire hosel cleaning tool I use which is only 3-4 inches long and wondering about a wire brush that is a foot long. Thank you.
@BrisGolf
@BrisGolf 7 ай бұрын
That is easy!! Great video and I will try that next time.
@valderja
@valderja Жыл бұрын
Nice tip. I've used the wire coat hanger method and it's been a bit messy in the past. Standing the club up on a paper towel is a great idea.
@matt7iron
@matt7iron 11 ай бұрын
How did you bend the hanger so close to eachother, pliers and needle nose pliers
@valderja
@valderja 11 ай бұрын
@@matt7iron Bull nose pliers. Just squash it tight. 👍🏼
@matt7iron
@matt7iron 11 ай бұрын
@@valderja OK and Im using Kingsford lighter fluid, rubber gloves, and after I'm done I wipe the grip down with rubbing Alcohol, never realised something right in front of me like a coat hanger can be used, saved $30 bucks at a sporting goods store.
@The559Jeff
@The559Jeff 5 ай бұрын
If you have a stationary tub to use, place the butt end of grip in and spin it inside the drain slot while using grip tool. This way there’s no mess and the grip won’t slide out.
@Jogaan03
@Jogaan03 Жыл бұрын
I still find a syringe and thinners works easy, just inject in a few spots and then twist the grip off with no tearing or stretching and no damage to the shaft.
@spennce
@spennce Жыл бұрын
I used to use syringes when I was younger but the risk of stabbing myself always worried me. Didn't want to inject myself with grip solvent😮
@larryjones8928
@larryjones8928 Жыл бұрын
Been doing that for years. A good way of doing it
@user-rt5pu1bw7r
@user-rt5pu1bw7r 5 ай бұрын
Thanks! Been using air compressor and have many grips blow apart lol.
@jeffnahass8373
@jeffnahass8373 4 ай бұрын
I like the tool you have. It works great.
@kennyg63
@kennyg63 Жыл бұрын
I have used a similar method for over ten years. This method is superior to the traditional needle method in my opinion.😊
@FRANKWOOLF2
@FRANKWOOLF2 Жыл бұрын
A coworker used the needle type and it broke off and stabbed himself in his thumb. He got gangrene and lost his thumb
@kennyg63
@kennyg63 Жыл бұрын
@@FRANKWOOLF2 That is the most awful story. Very sorry to hear that
@mksmith713
@mksmith713 Жыл бұрын
I prefer to use water and dish washing liquid. Makes it nice and slippery. With grip removal tool, it slides right off with no solvent wasted. The only problem I occasionally encounter is grip tape coming off inside the grip.
@martyflannigan5052
@martyflannigan5052 4 ай бұрын
I've always just used a syringe 3 or 4 holes twist the grip a little to spread the solvent and the grip slides off never had a issue
@bobliebsock3927
@bobliebsock3927 5 ай бұрын
Super easy. Great video!
@lanmurgatroyd9503
@lanmurgatroyd9503 Жыл бұрын
Oh my God.😲 total game changer👏
@user-tr9tv9qr7e
@user-tr9tv9qr7e 7 ай бұрын
Very informative. Thanks for sharing.
@marksakowski9272
@marksakowski9272 3 ай бұрын
I just use a small table top compressor and blow the grip off. To prevent damage to the grip I slip over a PVC tube just a little bigger than the grip that will prevent ballooning and tear of the grip. I can remove 10 undamaged grips in 10 minutes!
@ashleymillette9622
@ashleymillette9622 6 ай бұрын
Yep 👍🏿 😊Tried it and saved $$$$$
@sms9106
@sms9106 7 ай бұрын
Exactly how I've done it for the last 40 years.
@gamoholics4834
@gamoholics4834 4 ай бұрын
Thank you! Awesome video.
@mattdunshea4334
@mattdunshea4334 Жыл бұрын
Hi AJ. For some reason I can’t send you a message on the elite fit golf website, so I’ll ask my question here……what is the best/most adequate build tape to use for gripping clubs. I’ll be re-gripping my set on the weekend for the first time (using compressed air) and want to build up the grips. Thanks for your help. And thanks for the KZfaq content. Love your videos…..I’ve learned so much. Thanks from Australia. All the best. Matt.
@EFGMC
@EFGMC Жыл бұрын
Thanks. Just standard 2 inch wide masking tape is all you need.
@mattdunshea4334
@mattdunshea4334 Жыл бұрын
Thanks very much.
@ismomaki3558
@ismomaki3558 Жыл бұрын
Very good technique!
@TWTexasA1
@TWTexasA1 2 ай бұрын
Just buy one of those tools..Amazon has them $19 for one or a box of 2 for $25 ….they work great 👍🏼👍🏼
@Zerpersande
@Zerpersande 5 ай бұрын
My problem is that the tip of the tool can sometimes dig down and lift sections of the tape. This has the potential for problems if the tape isn’t removed and actually removing 5he rape if you go that route. There’s an art(luck??) of using just the right amount of solvent balanced by the right speed of insertion and turning.
@TSOSGERBY
@TSOSGERBY 5 ай бұрын
I purchased one of the grip removal tools ($51 in Canada). I am a novice at this. Will this work with JumboMax Ultralight grips or are they too stiff? Thank you for doing these videos for us.
@EFGMC
@EFGMC 5 ай бұрын
Jumbomax or similar with a harder cap will be difficult to use that.
@markkeating3609
@markkeating3609 Жыл бұрын
Just curious. I just regripped my 5-PW with CPX (midsize) grips. I like them alot so far. My question is should I put the CPX grips on my gap, sand, and lob wedge as well? I have tour velvet (standard) on those wedges. Am I just playing mind games with myself telling myself I hit the wedges better with standard tour velvets, or should you always put the same grips on all your clubs? Thanks.
@TheCustomCaddie
@TheCustomCaddie Жыл бұрын
Can you give a suggestion on what work bench you have or use? Specifically looking at the workbench in your old studio/shop with the vice grip on it?
@EFGMC
@EFGMC Жыл бұрын
That one was a custom build done by my father in law and me. It was probably 9ft x 3ft.
@joeparedes6026
@joeparedes6026 Жыл бұрын
Great am not going to waste more grips now🎉
@thecavitybackgolfer7083
@thecavitybackgolfer7083 Жыл бұрын
Nice. What about a Jumbomax grip? The top of the grip has a solid foam tip that is very difficult to slide this tool in. Any tips for those?
@MrHazz0
@MrHazz0 Жыл бұрын
Solvent with a needle injector and compressed air.
@thecavitybackgolfer7083
@thecavitybackgolfer7083 Жыл бұрын
@@MrHazz0thank you!
@michaelreilly5888
@michaelreilly5888 Жыл бұрын
Excellent tip!
@LowsHand
@LowsHand 11 ай бұрын
Very nice advice! I'm using an airpistol with a tube over the grip - have you tried that?
@EFGMC
@EFGMC 11 ай бұрын
I am crap when it comes to the air removal. Currently 2 for 10 in attempts even using tubes etc. I just stick with the v tool I show here. There I am batting .950!
@scotthucks7966
@scotthucks7966 Жыл бұрын
Great video! You are the best!
@BuckshotPA1
@BuckshotPA1 3 ай бұрын
Amazing tip!
@stephendaniel168
@stephendaniel168 2 ай бұрын
Say you just want to shorten the club and put the grip back on. Will the tape adhere a second time or do you need to remove it and replace?
@EFGMC
@EFGMC 2 ай бұрын
It usually will if it doesn't get torn up during removal. Let it dry and see if it's still tacky, then you know.
@mitchbush291
@mitchbush291 Жыл бұрын
Loving your Channel. I have a problem and I thought you might be the guy to solve it. I have a Super Stroke Putter Long Putter grip, the kind like Rickie Fowler is using, and I have a piece of shaft stuck inside the grip about halfway down all the way to the butt of the grip. The grip is new, so I would like to save it. Any ideas on getting the metal shaft out of the grip. Thanks in advance, keep on doing what you are doing, great information.
@EFGMC
@EFGMC Жыл бұрын
The shaft is broken off inside the grip?
@misstonya291
@misstonya291 Жыл бұрын
@@EFGMC Yes, I put a long shaft extension in the putter to try it out. When I took the grip off, the extension came off also and stayed inside the grip.
@terryholloway9930
@terryholloway9930 6 ай бұрын
Great tip again
@FrankDeAlto
@FrankDeAlto 29 күн бұрын
Will this method of removal work if you used the rubber cement method to install the grips?
@EFGMC
@EFGMC 29 күн бұрын
?? Never tried.
@lukejackson1933
@lukejackson1933 Жыл бұрын
We do big volume. Compressed air is so much quicker. Not without some fails though.
@mamin-br9gs
@mamin-br9gs 16 күн бұрын
Can I remove Putter grip the same way. I believe there is hard jacket in putter grip vs Iron grip which is only softer jacket ?
@EFGMC
@EFGMC 14 күн бұрын
Depends on the type of putter grip.
@pperrier14
@pperrier14 Жыл бұрын
This is brilliant, cheers
@jeremyyoder33
@jeremyyoder33 Жыл бұрын
Beautiful.. Thank you very much.
@GDubb_GG
@GDubb_GG Жыл бұрын
Nice video. Any tips for extra long Superstroke putter grips?
@EFGMC
@EFGMC Жыл бұрын
Those will often need a syringe to save them. SuperStrokes and Winn grips are always tough.
@garypostlethwaite4918
@garypostlethwaite4918 8 ай бұрын
Great video. 👍👍
@golfweed9947
@golfweed9947 Жыл бұрын
You prefer this method to the air compressor, or inflator?? If so, why? What are the advantages and disadvantages of both methods? Thanks.
@mitchd949
@mitchd949 Жыл бұрын
I've done the air compressor method - it works. But this method is very simple and quick requiring only hand tools, so you if you don't have shop air or a compressor handy it's a valid alternative.
@Otis790
@Otis790 Жыл бұрын
The worst thing about the air compressor method is breathing the solvent vapor . Not good if you do a lot of grips.
@EFGMC
@EFGMC Жыл бұрын
Grips installed with air shoulder be removed with air. Grips installed with tape and solvent I go with this method.
@Otis790
@Otis790 Жыл бұрын
@@EFGMC I was removing grips with solvent and air . Putting a short piece of an old bag tube to avoid grips exploding. Then I got the tool you showed today. Most of the time it’s very easy , and a lot cleaner. I repurpose a lot of old clubs ( some may say junk ) and trying to save a mature grip to match the set is sometimes the goal.
@wescarper43
@wescarper43 7 ай бұрын
@@Otis790 I've never needed solvent when removing with air. Just air seems to work fine as long as the grip is fully seated on the shaft, don't wanna use air if it is stuck halfway or something.
@1cleandude
@1cleandude 5 ай бұрын
You should give credit to Mr SGame for teaching you that method!🤣🙏
@EFGMC
@EFGMC 5 ай бұрын
?
@jamesdenyes9555
@jamesdenyes9555 Жыл бұрын
Great idea
@wooddm72
@wooddm72 Жыл бұрын
Does this method work on cord grips? I know they don’t work with the blow off method, curious if they do with this approach.
@EFGMC
@EFGMC Жыл бұрын
Yes, this will work probably 9 out of 10 times.
@jaygord
@jaygord Жыл бұрын
I use a syringe, inject a little bit of mineral spirits behind the grip, twist and pull
@adellase
@adellase Жыл бұрын
Does this method work with Winn grips? They don't "stretch" as much as rubber grips.
@EFGMC
@EFGMC Жыл бұрын
No. Those don't have enough give to them.
@jimhaider5530
@jimhaider5530 5 ай бұрын
right on 100%
@stevemcvay2220
@stevemcvay2220 Жыл бұрын
How do you feel about the fiber clear double sided tape compared to the white tape?
@EFGMC
@EFGMC Жыл бұрын
I hate removing it, always messier.
@jeffreyprice2982
@jeffreyprice2982 Жыл бұрын
Very nice!
@desmondmoss
@desmondmoss 7 ай бұрын
nice , thank you
@joewoodbridge5734
@joewoodbridge5734 7 ай бұрын
Does this method work for removing chunky putter grips?
@EFGMC
@EFGMC 7 ай бұрын
If you mean Superstroke or similar then its possible but likely will ruin the grip. Any grip with multiple layers will be much more likely to tear during removal.
@usa4x4trucks
@usa4x4trucks 3 ай бұрын
Does the tool scratch the paint on the shaft?
@EFGMC
@EFGMC 3 ай бұрын
I've never had that issue.
@JC-lh1pj
@JC-lh1pj Жыл бұрын
Cool thanks
HOW TO REGRIP GOLF CLUBS WITH TIRE INFLATOR
7:34
ELITE FIT GOLF / Mobile Clubmaker
Рет қаралды 346 М.
NEVER DO THIS WHEN REGRIPPING GOLF CLUBS
7:45
ELITE FIT GOLF / Mobile Clubmaker
Рет қаралды 721 М.
Ik Heb Aardbeien Gemaakt Van Kip🍓🐔😋
00:41
Cool Tool SHORTS Netherlands
Рет қаралды 9 МЛН
Blue Food VS Red Food Emoji Mukbang
00:33
MOOMOO STUDIO [무무 스튜디오]
Рет қаралды 22 МЛН
I Took a LUNCHBAR OFF A Poster 🤯 #shorts
00:17
Wian
Рет қаралды 9 МЛН
Can This Bubble Save My Life? 😱
00:55
Topper Guild
Рет қаралды 87 МЛН
Which Regripping Method is Better? Tape & Solvent vs Compressed Air
14:55
ELITE FIT GOLF / Mobile Clubmaker
Рет қаралды 52 М.
Save Golf Grip With Compressed Air / In THEORY!
7:33
ELITE FIT GOLF / Mobile Clubmaker
Рет қаралды 33 М.
The Easiest Way to Remove Golf Grip Without Damaging it
5:36
Darren Arber Golf
Рет қаралды 139 М.
How to Regrip Golf Clubs with a BIKE PUMP
10:05
ELITE FIT GOLF / Mobile Clubmaker
Рет қаралды 71 М.
Is Bigger Better? Testing JumboMax Golf Grips
15:54
ELITE FIT GOLF / Mobile Clubmaker
Рет қаралды 114 М.
Jeff Doin' Stuff - Golf Grip Removal Without Cutting
6:03
Professor Jeff
Рет қаралды 265 М.
Regripping your golf clubs using compressed air....easy
6:52
Stevie Jay Non Gambling Golfer
Рет қаралды 95 М.
Ik Heb Aardbeien Gemaakt Van Kip🍓🐔😋
00:41
Cool Tool SHORTS Netherlands
Рет қаралды 9 МЛН