Thank You so much! I hope it helped in some way!

Thank You Steve! I'm so glad that you found it helpful! It really isn't difficult to do! Good luck on the install and please let me know how it turns out!

Thanks so much Jack! Hopefully some may find it helpful to some degree! 🙏

Thank you so very much! I sincerely hope it may have been of some value to those folks contemplating such a project.

You are too kind brother. Thanks so much!

Thank You! I hope it helped! Good luck on the install!

Thanks so much Jorge!! My hope is that someone may be able to benefit from it if they ever consider installing a similar preamp pickup system. It can be intimidating for some!

Awesome! I have been considering doing the same on my classical guitar as well. Thanks so much for the feedback!

You are so very welcome Bob and Thank YOU in taking the time to watch and comment! I hope it proved somewhat helpful. I've had wonderful results with this setup, and I use the instrument quite frequently at gigs!

You're so very welcome and thank YOU!! I completely understand! I had not thought of that! Great idea! Thanks for commenting and sharing!

Thanks so much my friend! It means a lot!

Thank You so much! Cool!

Hey Jon! Thanks for your question! Fortunately, YES! It most definitely can be removed by simply using a guitar pick to pry and separate it from the mounting plate. It's included in the instructions how to do it. I hope this helps.

Thank you for commenting! I had a similar thing occur. Check the piezo pickup under the saddle. I replaced it and it resolved the issue for me. I hope this helps.

The controller itself can be removed from its bracket by using a guitar pick to pry it loose from the bracket. It just clicks in and out fairly easily. Once it is removed you can disconnect the microphone easy enough. It simply unplugs. To remove the bracket itself you can carefully remove by prying as well. It is held on by an adhesive tape. The piezo pickup can be accessed under the bridge. Remove the strings and lift off the bridge to remove. Keep in mind during installation, the bridge height was adjusted to compensate for piezo pickup thickness. Your action may end up too low once your remove the pickup so you may need to either replace the bridge or compensate by doing a setup on the instrument afterwards. So sorry to learn you have been having issues with it and that you have decided to remove it. The battery bag is held on by velcro and can be removed easily as well. I hope this helps. Thanks so much for watching and commenting!

Thank you for your quick and detailed response! I may try your techniques. Thank you again for making such great videos and being such a responsive KZfaqr!

@@gingold66 You are so very welcome Greg! Thank YOU in taking the time to watch, comment and like! It means a lot! 🙏

It's a great idea! I just thought it might be cleaner for filming purposes and having to reposition the instrument, etc. to simply remove the strings altogether. Thanks for the mentioning this option!

I'll have to check it out! Actually, there were no alterations to the soundboard per se. Only a height adjustment on the saddle to accommodate the piezo strip. Also, there is no gluing involved and the whole installation can easily be removed as well. Piezo strip does come in handy in certain environments. It helps reduce feedback in high volume situations. Overall, I'm very pleased with Fishman in general. I have a couple of their acoustic amps which complements the systems very well.

@@WEdHarris No doubt this sounds good, but Drilling a hole in the top (bridge), replacing saddle material with piezo stock, and an adhesive film under the soundboard (which might restrict the movement of the wood) are all just a big no for me on a D-35 but maybe on a cheaper guitar...the rare Earth Blend has some nice cork strips where the pickup meets the soundboard that allow for wood expansion and contraction and the actual contact area is a fraction of the Ellipse. No soldering, sanding or any prep at all other than reaming the endpin jack hole. Also, no thumping effect with the rare earth that you can get with piezo. My cheaper Martin 000-12E has that new MXT soundhole system in it and I hate it. Cant use it live because even with a $400 acoustic preamp/mixer I cannot dial out the piezo thump when I bare-tip fingerpick. I can see using the ellipse if I really wanted to hide the pickup. Plus, using Stewmac's Jack installation tool makes it a breeze to switch the Rare Earth Blend to another guitar. I have sold several guitars but have been able to keep my $300 pickup system each time.

@@billsmith3042 All great points Bill! Thanks for the intel. Fortunately, the Taylor guitars all come predrilled under the saddle and the end pins are factory ready to accommodate the jack. So no drilling was required in this particular install. However, I do understand and appreciate your point. Yes, I would not consider this particular install on my 1943 Martin 000-28 either! LOL But then again, I would never risk taking it out to perform with. On this install, there was no "adhesive" applied to soundboard. It uses double-sided tape. They just recommend cleaning the area prior adhering. I am a stickler for compromising or making alterations to any instrument. I own a few acoustic vintage collectables. I am not encountering any "thumping" on the piezo side, and I flatpick and fingerstyle on this guitar. However I am aware it would not be a good set-up for percussive playing. I do mix heavily on the internal mic thus reserving the piezo if I ever experience any feedback issues (which I haven't encountered thus far). The unit that is mounted underneath the soundboard actually clips into a bracket which is actually affixed via double-sided tape. I mention this only because the contact "footprint" is very minimal which is a nice feature in that the unit can removed easily. Just for the record, there is no soldering required on this system as well. Thanks again in sharing your experience and wisdom! It's always great to share such experiences! Not every application is universal to all situations and each should do their homework in weighing out the pros against the cons for their particular needs and go from there!

Hey Scott! Thanks for inquiring! It’s a Grand Auditorium 3 (GA3) model with a Cedar top.

@@WEdHarris I have a Taylor GS8 that I bought over 2 years ago. No pickup, just acoustic like your GA3. Had a local guy here put in an LR Baggs anthem, although I believe I could have done it myself on a weekend. I used to see a lot of posts from people who just simply loved the Fishman and LR Baggs pickups in their Taylors. Well worth the change! Great video, and thank you for sharing!

Yes of course! I would be honored! Could you also provide a link as well? That way I could direct traffic to your channel as well! Thanks so much!

@@WEdHarris Sure, no problem!

@@WEdHarris Hello ！ I'm here to provide a link to the video Thank you very much for your video material, which makes my introduction video much more colorful！！ Below is my video link：kzfaq.info/get/bejne/ic-RmtSCurnep6M.html

Thank You!