Just in case you were wondering how much this saves... I got a parts list for what he drew whipped up in digikey, and this is what I found: 3A toggle switch = $1.76/unit at 200 item price break (min quantity) 200 units = *$352 total* I will assume the 200 unit price break for the rest of these numbers and surface mount components except for the push button. If the minimum quantity is higher, I'll include that cost. 5,000 100k resistors = $6.46 (4,400 not used) 250 1M resistors = $7.99 (50 not used) 200 22uF capacitors = $16.86 200 30V 3.8A P-channel MOSFET's = $35.00 200 Dual NPN transistors (2 transistors, one package) = $25.90 200 Through hole momentary push buttons = $15.18 Total price = *$107.39* Less than 1/3 the price! And I didn't even try to make things better by trying to minimize the number of different parts.
@the_atomic_kebab3 жыл бұрын
Yes, but you must consider also the operation cost. The pcb must be manufactured, the electrical components must be placed an soldered. If you are gonna place this components on a pcb which already is designed to be in your system, the influence on the operation cost for this feature is almost insignificant. Anyway, the final price tag is still below.
@ohmslaw68563 жыл бұрын
Well, that's the problem.. your buying off digikey haha
@CXensation3 жыл бұрын
Try expand the calculation by comparing the pcb cost, pcb assembly and fitting vs Drilling a hole for the toggle switch, soldering leads to the switch and fitting the switch Yes - I do consider the electronic solution done with other electronics fitted anyway. As a former PTA engineer I learned to avoid any extra manual assembly cost on the production line.
@thekaiser43333 жыл бұрын
You forgot to factor in 200 breadboards at $2 a piece...
@fifaham2 жыл бұрын
As you go higher in production count the end cost may worth it, because the robot machines can populate all those parts in 3 seconds and the addition of the PCB is almost negligible. It is good alternative however.
@MostFolkCallMeOrangeJoe9 жыл бұрын
EEVblog Please do more videos like this, showing how circuits are developed, I learnt so much from it. I like it,
@mrquint158 жыл бұрын
+Adam Harrington +EEVblog yes please! this REALLY helped me grok a few things. would love to see more like this one. Thanks for keeping this going!
@markuscwatson7 жыл бұрын
same!!
@freezxify7 жыл бұрын
It's seems hard to find proper circuit development tutorials around. This one was perfect!
@Justsquareenough7 жыл бұрын
ditto
@happyhippr6 жыл бұрын
This channel is solely responsible for getting me hooked on electronic circuit design
@mathewk29617 жыл бұрын
FYI for those novice, such as myself, who are building this soft latching switch. I had been working on making this switch work for over a month. I'm using all bjts. I tried different resistors, different capacitors, and different types of bjts. I could not get it to latch off. As soon as I let off the momentary switch the light came back on. Holding down the push button I could get it to flash like Dave's but it would not stay in the off position. Finally I went back to original components and then it dawned on me, after viewing Dave's video a couple of dozen times, the LED I was using was not a sufficient load. I put in a 1/2 watt 2200 ohm in parallel with the LED and viola! It's working! Thanks Dave.
@0x8badf00d6 жыл бұрын
It may be the leakage current. I've witnessed a thyristor made of jellybean BJTs turn on by itself due to leakage.
@shamsheralamraja7 жыл бұрын
Hi Dave, I have a slight improvement on the circuit, move the capacitor to collector of the T2 and remove 1 M resister from base of T2, connect both bases togater and put switch between the collector of t2 and basses. replace 100 k resister with 650k at collector of t2 and vcc.works just fine , no more ocilations, hold the switch as long as you want
@jozeftorok66677 жыл бұрын
Works great, thank you very much !!!
@renatokristic88007 жыл бұрын
This works great :)Thank you :)
@JK360noscope7 жыл бұрын
Anyone have a diagram for this? Is the capacitor in series with the collector of t2 or between collector and ground? Intrigued...
@mrstevesmall7 жыл бұрын
Jacob Kon between collector and ground
@keldsor7 жыл бұрын
How about an explanation WHY it works ... is it as "good" as the original concerning current in OFF state ?
@ddandrews8258 жыл бұрын
Your channel is damn good. The way you describe things from simple to complex can rival the best tech school teacher out there. I am learning things I've never bothered to learn, all thanx to your channel. Cheers.
@daviddaigle48417 жыл бұрын
Absolutely agree
@ReactanceIsFutile6 жыл бұрын
For anyone wanting to simulate or build some of these circuits as Dave goes along, remember that BJT transistors realistically require either a pull-up or pull-down resistor in order to ensure their default state. For example, in this video, at minute 4:00, this circuit would likely actually start in the ON condition without pressing anything because the base of Q1 (the PNP) transistor is not guaranteed to be held high, and is likely close enough to ground, it will start conducting, causing Q2 to fire turning the circuit on. If we use 100K-Ohm resistors everywhere to keep current low on the base of the BJTs, a weaker pull-up is necessary on Q1 simply to ensure the base is high on startup but can be easily overcome by the ON switch, grounding the base. For this pull-up, simply connect a 1M-Ohm resistor between the collector of Q2 and the emitter of Q1.
@user-vo6yr8rf4c2 жыл бұрын
You are right.... In reality this 4.00 circuit will be pretty unstable.... We just have to use a big resistor between the collector and base to ensure that the base of Q1 remains high enough not to turn on randomly.
@Vulpusvulpes Жыл бұрын
Youare actually right, I tried to make the circuit at 4.00 but turned ON by itself and the ON sswitch seemed to be doing nothing at all. I will try with your suggestion again
@MlokKarel Жыл бұрын
Would I read this earlier, I would save myself some 8 hours of building and simulating... 😂 On the plus side, I am able to simulate this circuit in CircuitJS, TinkerCad AND Ltspice... 😅
@evgenysavelev8378 жыл бұрын
Congrats man, your video is now offered as a first result when looking for a soft on/off circuitry. This must mean something.
@tuxthemagicpenguin9 жыл бұрын
Living in the US I had never heard the phrase "half a bee's dick" before. I burst out laughing. Thanks Dave!
@jeetenderkakkar75703 жыл бұрын
Laughing
@Necrocidal3 жыл бұрын
I'm from UK. I'm learning a lot of awesome Aussie slang from this channel.
@gernoteyssler82969 жыл бұрын
It's a really good idea! Thank you! Remarks: 1) for the second transistor use a NMOS --> no big capacitors needed 2) use a resistor from basis to ground for the first transistor - helps against leakage current 3) If the battery voltage is more than 15V ... 20V, most of the PMOS don't like this and go to the semiconductor heaven.
@VK6TT3 жыл бұрын
re pt 2 - i had issues with the filter cap of the downstream circuit bleeding back through Q1 turning it back on. A 680k resistor as suggested solved this
@BobD10019 жыл бұрын
Dave, as always your tutorials are the best around! Your videos have taught me more than many of my electrical engineering classes. Thank you!
@kmuns46 жыл бұрын
Commenting again because this is that good. This is the first video by EEVblog I've watched, but communicating the thought/development process of a circuit is what I've been searching for since my undergrad years! Extremely impressed. And delivered with an Australian (?) accent? Amazeballs, and Bob's your uncle.
@sachiperez8 жыл бұрын
Bob IS my uncle. First time I heard you say that it kind of freaked me out. I had never heard that phrase until I started watching your AMAZING videos. Thank you for all the great information and for the care you take in presenting it.
@EEVblog12 жыл бұрын
Yes, it will usually be cheaper, cost it out yourself. It's not just about cost either. Sometimes you want/need a soft switch instead of a big clunker mechanical toggle.
@ernststavroblofeld19619 жыл бұрын
My secretary is bi-polar too. And she works as a soft latch switch like a beauty. Almost telepathically. Bingo! Thanks for the inspiration.
@marionetadelplaneta9 жыл бұрын
Ernst Stavro Blofeld does she has high input impedance if you know what i mean ?^__^
@ernststavroblofeld19619 жыл бұрын
marionetadelplaneta She does, but that is none of your business.
@marionetadelplaneta9 жыл бұрын
Ernst Stavro Blofeld what's so private in asking if someone is friendly?
@ernststavroblofeld19619 жыл бұрын
marionetadelplaneta I signed a nondisclosure agreement.
@JK360noscope7 жыл бұрын
And here I was trying to find a reasonable price for a switch that could handle 200 mA and wasn't momentary... I should ask for them to rescind my degree for the amount of time I've spent on this! It's almost like I could've saved precious time by watching every video from this channel! Beauty!
@iblesbosuok5 жыл бұрын
your explanation with green ink makes it far more clear. clearly you prioritized how to think comprehensively. salute to you. cheers from Indonesia
@victordss3 жыл бұрын
Important: if you have a capacitor on the output, the comportment becomes erratic. It will not latch off anymore (will turn off only while switch is closed), and oscillation becomes unbalanced.
@CuentaSpam2312 жыл бұрын
13:37 "My product never has bugs. It just develops random features."
@BlackXeno3 жыл бұрын
Interesting the 1337 timing... like "1337" slang on Reddit. Creepy coincidence...
Bread Board Success: I built Dave's circuit and it worked. Things to note: - I used a 5Vsupply. - I used an IRF9Z24N P-MFET. - I used a 47uF e-cap. Dave spec'd 22uF, but actually used a 47uF on his board. I like the button press timing of the 47uF better. - I used a red, SMD LED with a 1K resistor, for the load. - Dave's circuit starts in an on state, when power is first applied. To me, this is a problem. Say this is on a stereo and the power goes off/on in the night. The stereo is going to startle you awake . However, for whatever reason, mine does not start in the on state. Lot's of fun, Mr. Dave = Thanks!
@pixelsafoison5 жыл бұрын
You can't fathom how much I'm learning from your videos. I always have a sheet of paper and a pen at the ready when watching your tutorials x)
@Mr_Meowingtons7 жыл бұрын
OMG i have been looking for some thing like this... i would like to see you doing more projects like this..
@SatyajitRoy20489 жыл бұрын
I don't know who's clicking dislike button on this nice piece of video.
@renelefebvre539 жыл бұрын
very simple, very clear, very usefull. I have a lot of push buttons and this is the features I look for. Dave, you are the BOSS !
@akashnigam0109 жыл бұрын
This is one of the best tutorials i ever came across... Thank you so much Dave for this solution.
@trunovmichael8 жыл бұрын
I tried the circuit @04:00 with BJTs, but without the buttons. On 'out' I had a resistor followed by a lit LED. In theory it was supposed to be off. Apparently, there's a thing called 'transistor leakage'. It means even when a transistor is in cut-off state, some current might still go through (micro-Amps in magnitude, I guess it varies among the different types). I suppose it could be ignored if applied to load, but when it's connected to a base of another transistor - it gets amplified, then it feeds the first transistor and we end up with fully activated circuit. I hope this comment will save people about half a day of puzzled head scratching. In the end it was fun to find that out, probably I should have added a "Spoiler alert" in the beginning :)
@martinwestermeyergondonnea846 жыл бұрын
OMG I LOVE YOU, i thought i was just dumb
@dharmikbhavani72725 жыл бұрын
just add one small capacitor between emitter and base of a PNP transistor and it will work as theory describe.
@Vulpusvulpes Жыл бұрын
If referring the circuit at 4:00, just add a 1M resistor between the emitter of PNP and the collector of NPN.
@leochang2228 ай бұрын
@@dharmikbhavani7272 it works well!! thank you
@bob4analog9 жыл бұрын
Tap on the white board...Yes! Very good, mate!
@NgocDangDinh3 жыл бұрын
Dear EEVBlog, Thank you very much for your lovely video on Latching. I am doing a small project on controlling small out put (max 20mA 5VDC) with 02 source of separated Inputs as following: 1. Input 1 (Vin1) of about 4.0 V at HIGH and 0 V at LOW (maintained continuously until the switch is off) 2. Input 2 (Vin2) of about 4.96V at HIGH and 0.3 V at LOW (maintained continuously until the switch is off) What I want to do is: 1. Upon Input 1 turn on High or Low the Output will toggle its state; 2. Upon Input 2 on turning HIGH/LOW the Output will toggle it's state as well. I don not care on the state of the out put is HIGH or LOW but I do care about changing the state of each input, the Output state will toggle ON/OFF respectively. This case is similar to controlling of staircase lamp with 2 two-way switches. I hope you would not mind taking sometime to advice me with thanks.
@SandeepSandhu3 жыл бұрын
What an explanation, watching similar video on another channel which was made 9 years after yours but I must say, your explanation is at par.
@power-max9 жыл бұрын
I paused the video at near the beginning, and I tried to make a own solution to this, and I came up with the EXACT same solution you did! LOL (I just used 1K resistors in LTspice instead of 100K and 1M ones.)
@organizedfromwithin25259 жыл бұрын
Power Max While the NPN transistors are ON, you'll be drawing 100x more current through both of your 1K resistors than if you used 100K resistors, stressing them more. For production, you'd probably want higher reliability, thus higher resistor values.
@power-max9 жыл бұрын
downthetube within Well it was a simulation, I often use the 2N2222 transistor in LTspice in such a way it ends up dissipating many hundred watts. Not an issue! I often use TO220 transistors when prototyping stuff, as they are more difficult to destroy. However the disadvantage is that more base current is necessary for bias the transistor, and consequently I will end up using low value pullups for the bases. For small signal transistors and darlingtons and stuff, you are correct.
@organizedfromwithin25259 жыл бұрын
Thanks - I was just mentioning some obvious improvements as a design philosophy. Guess I'd have to look up datasheet for 2N3904 to see how much margin is left when increasing from 1K's or decreasing from 100K's. Another issue is power budget or allotment on the input power form. Of course, how one makes these compromises and reiterations in design are largely dictated by an overall product specification, implementation, schedule, budget, and all the "ilities". The video is a fun, nicely explainable circuit. cheers!
@kkeinob7 жыл бұрын
The bad thing is that the FET is ON after plug-in. Who want to have circuit activated after plug-in? If then you do not need this circuit at all. I think if you add BE resistor to the transistor on the left should solve the plug-in problem. The voltage at the resistor should be lower than 0,5 V assuming the leak current from FET. As it was explained by Trunov Michael bellow.
@MrPinknumber7 жыл бұрын
Loved it ! I had to pause for like 5-10 min when he showed the circuit, trying to simulate the thing in my head, and was able to do it :) Learned a lot from this, thx.
@oskimac Жыл бұрын
this video is so good. i already made the circuit years ago. and today i was in the need for something like that and remember it. i don't have any toggle switch at hand but plenty of transistors, resistors etc.
@MB-st7be6 жыл бұрын
Just here for a bit of nostaligia for when Dave's videos were actually about circuits! Now they're all mail bags and teardowns, like every other channel :(
@EEVblog12 жыл бұрын
Please show me a simpler design for a discrete soft latch power circuit. There are many reasons to use such a circuit, not just cost.
@aaronmurphy50607 жыл бұрын
Awesome vid. Quite helpful to see AND hear why things work or don't. Usually you get one or the other. Time to get busy making stuff, thanks for sharing
@marciojpcardoso7 жыл бұрын
This circuit is a killer. Simple and functional. Love it. Thank you so very much for this!
@smbrob9 жыл бұрын
Great tutorial Dave. Maybe you should do this more :-)
@gorillaau12 жыл бұрын
"..And for those that hate me tapping on the whiteboard." Ha ha. Nice line :-)
@chrisbroome6 жыл бұрын
LOL. I gave it a thumbs-up just for the tapping on the whiteboard at the end. That was hilarious.
@miketony20695 жыл бұрын
"And for those who hate me tapping on the whiteboard just for you".... Instant subscribe after that .... well done Dave
@matthehat10 жыл бұрын
"Half a bee's dick" KZfaqr phrase of the week
@brettski746 жыл бұрын
I quite liked the circuit at www.mosaic-industries.com/embedded-systems/microcontroller-projects/electronic-circuits/push-button-switch-turn-on/latching-toggle-power-switch - see figure 3. two MOSFETS, 3 resistors and a cap.
@HopWorksET11 жыл бұрын
I absolutely love your videos! Usually, analog+me=fire! but your detailed explanations of the theory has given me confidence, and I have less fires and explosions on my breadboards now. So not only have you helped my understanding of electricity, you have helped to save the world as well! Hey! Bob's your uncle! Great job and thank you!
@yanava5 жыл бұрын
I've always implemented this with a JK Flip Flop and a pass transistor. Great to see a discrete implementation!
@m1geo9 жыл бұрын
"Half a bee's dick" hahahaha
@ryanoconnor79579 жыл бұрын
I love that half a micro-amp is half a bees dick in Australia.
@markk440910 жыл бұрын
So instead of using an on/off switch, add 6 more components to an on/off switch and you now have an on/off switch! Did he really say "Half a bee's dick?"
@IvanIvan197410 жыл бұрын
...and don`t forget the Christmas illumination when you hold the switch.
@magicponyrides9 жыл бұрын
You can't really be this dense.
@IvanIvan19749 жыл бұрын
magicponyrides What do you mean exactly?
@RWoody19959 жыл бұрын
IvanIvan1974 he means the point of this is that its cheaper to implement because it means you don't need a beefy switch and can use an elcheapo switch without blowing it up :) if you were just joking it didn't work, this is text its hard to tell so you should expect those reactions from people :)
@IvanIvan19749 жыл бұрын
megaspeed2v2 I don`t even know if he wrote to me. His reply is not directed to me. BTW, I use switch system like this too, I implement it a little bit in a different way but actually it`s quite similar. (without Christmas illumination)
@esjaymac10 жыл бұрын
Love the tapping...and the accent. thanks for this!
@tsraikage3 жыл бұрын
man. im watching this video 5th times. your explanation is so satisfying i keep falling asleep.
@zwz.zdenek10 жыл бұрын
I'm disappointed. I'll just take the liberty to throw the jellybean rule out of the window based on economy and employ a CMOS divider/counter. Then just one resistor, one cap (those just to smooth out the button input) and an output transistor and Bob's your uncle! No blinking, no residual current (which you forgot to fix in your design), an option to make several ON modes in sequence... and the price will be the same!
@ilike600baud10 жыл бұрын
Sounds interesting! I know nothing about that kind of circuitry (sounds like logic!). Please make a video on a design concept and give us a walk through! Especially of the power-on sequence capability. Then throw a couple part numbers in there so novice people can get up and running! It'd be great!
@GRBtutorials5 жыл бұрын
Or just use an MCU if you already have one (very probable), a pushbutton, and a MOSFET. Problem solved for a few cents!
@Wren69915 жыл бұрын
How are you setting the initial state of that counter after power on?
@johnfrancisdoe15635 жыл бұрын
Luke Wren Also, I doubt his CMOS chip has as tiny standby current as the circuit in the video. Video circuit standby is dominated by C-E leakage in the left BJT.
@Wren69915 жыл бұрын
@@johnfrancisdoe1563 that's true! I have one major problem with Dave's circuit though, which is its sensitivity to bleed time of the system load. Large output capacitance and small load -> 2N3904 becomes biased again and doesn't switch off. I think any circuit where you try and be clever and use system load as a switching element can have this issue. My current favourite circuit involves a latch built from a dual inverter IC, e.g. 74LVC2G04. They cost around the same as a small-signal transistor, leak around 4 uA, and give you clean switching every time. I think the lesson might be "if you want a latch, build a latch" :)
@MrXerotom9 жыл бұрын
does this work on 12v to power up a relay?or what i need to change?
@EfficientMan3 жыл бұрын
You were right, leave it to us to play with the value of resistors. You made me spent hours playing with it and trying to make it as good as I can. Finally I managed it, my main goal was not to turn on again when I turn it off if for any reason I keep the button pressed. So brief press to turn on and brief or not brief press for turning off.
@964tractorboy12 жыл бұрын
Beauty! Love the tapping on the whiteboard too - I was in fits. I wouldn't have dared pull you up on it, but...
@linuxguy11999 жыл бұрын
Is there an auto dislike bot on KZfaq because every one of your videos has roughly the same amount of dislike and it's almost every channel on KZfaq all having about 30-100 dislikes so wtf???
@EEVblog9 жыл бұрын
Jeremiah Lowe There is a core group of people who thumbs down all my videos, some within minutes of uploading. They haven't even watched it yet. I don't know about other channels, but I have a core group of haters!
@ElectronicMarine9 жыл бұрын
EEVblog that's how you know you're doing something good :)
@linuxguy11999 жыл бұрын
EEVblog i knew itd be something like that btw do you know any cheap power supplies like under 50$ mine broke and idk why it was a computer PSU anyways
@superdau9 жыл бұрын
Almost all videos have approx. 1% downvotes. That's the "standard". Less downvotes than that is either a video on a small channel or what you could call "exceptionally" good. A higher percentage means you either said something controversial or just too much stupid/boring stuff.
@olaostehvel97639 жыл бұрын
EEVblog You're pretty harsh sometimes and some people really don't like that. Me on the other hand I would give thumps up for the sole reason of being able to speak clearly even if it means to bash people who deserve it. Well that is if I could get myself to use the (dis)likes buttons at all. I believe they are made for immature people who actually beleive quality derives from how many likes one gets. Even though enormous amount of proof points in the opposite direction, stupid people (which includes most of the human kind) still cling to the lie. You are doing a great job teaching electronics and I hope it is enough money for you to keep on making videos until death. If it was something I would like to see more of it would be rf. Maybe even a simple DIY spectrum analyzer just to crack the nut about it being so hard. You are a great teacher and you would know how to make so called hard stuff simple to understand. Against, I really appreciate your videos.
@Robonza9 жыл бұрын
If understand this correctly. If you had a power cut then this thing will turn on the device. Can you modify it to start up in the off state?
@0x8badf00d6 жыл бұрын
Uh. This doesn't start up in the on state. The gate of the *P*-MOS is pulled up and the transistor that pulls it down has no base current before you press the switch.
@rbhis0005 жыл бұрын
@@0x8badf00d Uh. It can start in the on state. You're clearly missing something in your highly simplified response. Don't be a shit.
@deandremahadeo95597 жыл бұрын
Love your videos! this one you have turned World's Simplest Soft Latching Power Switch Circuit to the most complicated one.
@ixamraxi12 жыл бұрын
This was an *excellent* video, I appreciate you taking the time to explain the how and why in so much detail, as well as giving us the opportunity to ponder some of it on our own. Have you considered teaching as an occupation? You have a knack for it. Tap away!
@teuton83637 жыл бұрын
why not replacing the 1M by a 100k (and 22uF cap with a 2.2uF) so that the BOM gets smaller?
@0x8badf00d6 жыл бұрын
Check your math. The time constant would be a hundredth. If you go down in resistance, you'd need to go up in capacitance.
@DaffyDubzFPV7 жыл бұрын
LMAO is it me or does he say "Half a Bee's dick" at 15:48
@SLJB89 жыл бұрын
Made it seem so simple it's brilliant! Thanks Dave.
@faridsafazadeh1137 Жыл бұрын
Did not have that P channel Mosfet you used. I had IRF5210 so used that. Worked like a charm first try! Thanks for sharing. You are just amazing. Although I will modify this and using this as an oscillator. I like the wave form coming out of it. A very neat square wave.
@T7thK9 жыл бұрын
I'm in need of a latching circuit like this, and I was about to use a J-K Flip Flop to do the job, but that would require a debouncing circuit with a schmitt trigger. This circuit looks neat, and it just might work great for my application. Thanks Dave!
@johnterpack39404 жыл бұрын
The one thing I don't like about this is that it defaults to ON whenever power is first applied. I'm interested in this sort of circuit for a couple automotive ideas I have, like being able to turn cargo lights on/off from either the cab or the cargo area independently. The idea being that momentary switches in parallel in the separate locations could toggle the state of the circuit. Obviously I don't want cargo lights turning on every time I start the vehicle and I also don't necessarily want them wired always-hot. But your presentation style made it fairly simple for an electrical dunce like myself to follow the logic of the circuit. Thanks for that.
@fabiovsroque8 жыл бұрын
What a nice electronics project design class, I'm speechless, thank you very much!
@user-fi1sn5cw2o9 жыл бұрын
Схема простая, но - гениальная! Питаю с помощью нее усилитель - ОЧЕНЬ ДОВОЛЕН! GOOD LUCK!!!
@KeritechElectronics Жыл бұрын
Plain simple and elegant; can be combined with over-discharge protection.
@nevtelenfelhasznalo615112 жыл бұрын
Thank you very much Dave for that fantastic video! :) You are a very good teacher. Thank you for doing the EEVblog channel. I enjoy watching it and often find it quite enlightening.
@SkylerF11 жыл бұрын
Thank you so much for this. I have been wondering how to do this since I was really little (im 14 now) and this was great info. Everybody that I asked said to use a microcontroller, but this is the first simple solution that ive seen and works great!!!!!!!!!!!
@postal260011 жыл бұрын
I want more videos like this in favour of the teardowns... I learn more from this kind of videos. Who's with me? :P
@clintonraubenheimer58799 жыл бұрын
I have been looking for this kind of circuit for ages. Whats great is, now I also understand why it works the way it does. Since I'm new to circuitry this instructional has been the pretty insightful. Not that it's that it's going to deter me from watching, but I find that typical Australian way of describing things by dipping the voice slightly distracting, and had to go back a few times to regather. I'm sure I will get used to it soon enough though. Thanks for the vid.
@andrewkay9226 Жыл бұрын
What a great presentation - I've learned something & enjoyed doing so. Thanks
@w0mblemania11 жыл бұрын
Thank you for this video. I love these simpler, how-to tutorials.
@skoue41655 жыл бұрын
Really liked the video and I can see some good reasons to do this but not sure cost would be one. You can get a ten pack of latching pushbutton switches rated at 1 amp off Amazon for $8 US and a 30 pack of mystery spec ones for $6 US. Now the ability to be able to switch it off automatically could be important for some things so? Nice to know how to do it though and I love that you explain the why's as you go.
@Jono66717 жыл бұрын
wow I'm a complete noob and know nothing at all about transistors, but this video was still very helpful. thanks!!
@agstechnicalsupport6 жыл бұрын
Thank you for the instructive video on MOSFET power switching experiment.
@TGV4448 жыл бұрын
Thank you for the clear explanation, saved me a lot of struggle!
@kenzuercher74973 жыл бұрын
"...and Bob's your uncle!" Great explanation!
@madcockney3 жыл бұрын
That expression appears to have come from the UK, probably in the 19th century, and travelled to some other English speaking commonwealth countries. It is still used in England and Wales, not sure about Scotland or Northern Ireland. It's only when watching YT videos from visitors, some having settled here, from other English speaking countries that you realise how many euphemisms, expressions and sayings we have and why they sometimes find us odd, hard to understand, though interesting. Me, I'm odd all the time! Though Australia and New Zealand do have their own expressions, etc we do share many.
@TheCrazzyToobinator11 жыл бұрын
I found this circuit to work best driving a relay, it worked very good for that, and you can switch high current supplies with very little trouble this way.
@DuongTrongHue9 жыл бұрын
Always get useful info from you. Thanks Dave
@BlensonPaul7 жыл бұрын
google first hit on 'mosfet latch' video . awesome Dave !
@JerryEricsson8 жыл бұрын
Nicely explained, I think I could perhaps build one of these should the need arise. Thanks for the education.
@MrTriac12 жыл бұрын
You didn't get the idea, it's about saving energy. The NE555 would draw current from the source either the output is in 1 logic state(ON) or 0 logic state(OFF). Even the CMOS version(LMC555) draws a little amount of power. This one draws current only in ON state, which could be an advantage in some applications such as battery powered/portable apparatuses/appliances.
@ashmcgahee63898 жыл бұрын
Great explanation and walk through, very solid final circuit! Thanks! I ended up using a DMG3415U, which you can put a couple of amps through at RDS(on) of ~40mohms, and still about the same RDS(on) as the IRF9110 at small loads. Definitely still taking recommendations though if you have a better one - there are a ton of P-Fets out there to try and compare.
@1liftman12 жыл бұрын
I like the fact that I could actually understand most of this video! :)
@fernanmady18612 жыл бұрын
Beautiful. Simply beautiful teaching.
@Fruktodlaren9 жыл бұрын
You make electronics fun and interesting, even for a dabbler like me. Keep up the good work!
@sdplusm38 жыл бұрын
Thank you for the idea. It will be a very good starting point for me and I've learnt a lot.
@uber-jaianada11 жыл бұрын
I especially love the idioms.... and the white board tapping heh heh. Thank you for the tutorial!!
@slaznum19 жыл бұрын
Thumbs up for tapping on the white board.
@vaio2326 жыл бұрын
Thank you just what I needed, very informative and well explained. I was building a portable lithium battery charger with one tactile switch. Best solution by far, but still there are caveats like with everything, Mosfet threshHold, if it reached maybe 2.6v lets say, and you have a battery that went down but has a lot current power, and your load is heavy. The mosfet might get really hot because it does not like to be in saturated voltage levels, it needs proper 5v and 0v or negative to turn on or off, thus my thoughts of using a separate power supply to turn on or off the power Mosfet once turned on.. Just need to modify your circuit detect if button is pressed or not with micro-controller, in case I need one switch to do many functions, like two fast taps to enable debugging mode or etc. Nice vids, keep up the good work!
@W4llyB4nger11 жыл бұрын
Brilliant... I've been looking for something like this all week. Thanks!
@headstonegraveyards53707 жыл бұрын
This video is awesome, this is the kind of content I like the most, thank you!
@kmuns46 жыл бұрын
Absolutely fantastic. The way electronics should be taught. For a second forget about voltage and current values and just think about flow & connectivity to produce the logic that you're looking for. 10/10 would (will) watch again.
@chrisstorm77042 жыл бұрын
Had to give it a thumbs up, just for tapping the whiteboard.
@m3chanist8 жыл бұрын
Great video, you have a natural design sense (could actually call that a feature) rofl. Cheers mate, I'm shamelessly ripping off your circuit for my project as I type. Top work.
@SeanStrongman9 жыл бұрын
This is great, i already know , that i could use this circuit in my project , thanks Dave!
@Thaddeus3rd9 жыл бұрын
Your videos make me so happy.
@m4d3ng8 жыл бұрын
The explanation for this reminds me of the how it works section in the DSE fun way instructions
@pman190210 жыл бұрын
very nice... i also love you tapping on the whiteboard :D
@snaprollinpitts10 жыл бұрын
Dave, you are DA MAN, and I like it when you tap on the white board!? and Bob's your uncle!
@JeremyVeleber12 жыл бұрын
I like it, Dave. I'll use this. I would love to see it use a capacitive touch button too.