🤣 They make it look 👀 so easy. 😂

Funny about that .@@ManMountainMetals

It 🔥 burns, it burns.

🤣 I bet. I bet that’s be good the chop up wire though. Like so it’s not a big ass roll of slop in a bucket. 🤷🏽‍♂️ I’m sure it has a safe practical use somewhere 🤣

@Kēvin Rose if the bottom cutter was gear driven by the upper cutter, it would be a much better tool.

I'm going to say, yes. Yes you can.

No. I checked out some other people's videos, and it is the most common complaint.

@@ManMountainMetals ok thanks for the info. I won’t be buying one 🤣

@@Scrap2Cast I can't imagine cutting along a line would be easy. Maybe using 2 hands would help if you didn't have to hold the workpiece.🤷

@@ManMountainMetals I’m willing to bet if you can clamp the sheet metal down it could be easier or have a buddy hold the piece 🤷🏻‍♂️

Not great. It has only one powered cutting wheel, so a significant amount of force is required. It is difficult to both push and guide the tool simultaneously, I'm sure it could be done with practice, but it is substantially different than shown in the ads. thanks for watching.

It beats using hand shears but didn't live up to expectations 😕

They are advertised as being able to cut mild steel. The metal in the video was galvanized aluminum (zinc coated aluminum) that I was cutting. That is about the least thick and softest roofing material a person would want to use. Any thinner and the nails pull through the metal sheeting in any kind of wind. If both wheels had been geared to turn instead of just one, it would have worked a lot better. I am glad you found them useful, and I appreciate you watching my video. But I honestly think that most people that buy this tool are going to want to use it on something more substantial than superloom sheets (had to look that up BTW, 😆) and as a roofing tool it's really not up to the job. IMHO.

I agree about the curves.🤣 My main problem with that small bit of metal I was using is that I needed two hands on the drill, one to hold the trigger and one to push and guide. The trick is I also needed to hold the piece of metal, so I plumb run outta hands.🤣 If the manufacturer had geared the anvil head to run with the cutter head, it would work a lot better. As is, the cutter turns but the anvil doesn't and it takes considerable effort to push the tool through the work piece. If you were cutting full sheets you could just throw some blocks on it to hold it in place while you used both hands on the drill. Thanks for watching, I can't believe my dumb little video got 11k views.

@@ManMountainMetals I noticed from watching a few reviews of this piece of crap that people that had the drill set on high had better performance and didn't need to push it so hard to get it through, also giving them a straighter cut line.

It's another MVP, minimally viable product. If the lower gear had also been powered instead of free wheeling, I believe it would function like the one in the infomercial did. It beats tin snips but would be awkward to use one-handed as you have to guide and push the drill.

If both the cutting wheel and the anvil wheel turned at the same rate, gear driven, for instance, it would be a much more usable tool.

I went back to where I purchased it from and gave them a serve of what I said to you , typical dodgy Chinese .@@ManMountainMetals

Man Mountain Link buying into the hype so you don't have to 😉👍

Yeah, but when you finally need it, ya can't find it. 🤷

@@ManMountainMetals Dude you stating facts . 😂

right under $15 usd delivered.

www.ebay.com/itm/295724072431?mkcid=16&mkevt=1&mkrid=711-127632-2357-0&ssspo=qelree9zrbw&sssrc=2047675&ssuid=wILlK5tOQc2&widget_ver=artemis&media=COPY

Squiggles to you, also, and thanks for watching 😉