Would be awesome, those e foils are 10,000 dollars and a ripoff. I bet he built it under $2000 just put a lot of man hours into it.

Thanks very much :)

Thanks Zachary, I used an A1 Carbon Fibre Mast/Foil which I got off Ali Express. I Used a 480kv sss56104 motor with a 6:1 planetary gearbox, a 130 amp water cooled hobbywing esc and 4 x 6s 11amp hour batteries running in a 12s configuration (22 amb hour 12s). Cheers

Hi Luke, I didn't have any trouble getting the epoxy to stick to the polystyrene. I used some Red devil onetime spackle filler to fill in any voids in the polystyrene and then gave it a sand and made sure it was as clean as possible before laying the fibre glass and epoxy. Cheers

@@bengolddesigns9343 Thank you!

Pablo Quispe Hi there. I bought the hatch of www.burnsco.co.nz and the two electronics boxes off RS Components.

@@bengolddesigns9343 Thanks Ben

Thanks. Has the hatch leaked at all? Some complain theirs leaked.

Hi there, I bought it from AliExpress, thanks. NZ$ 721.95 10％ Off | 100％ PURE Carbon Hydrofoil Water Wings Foils Hydrofoil Thrust Surf Foil for SUP Surfboard a.aliexpress.com/_mNhyeqq

Hi there, it ended up being about 125mm thick in the middle. Cheers

@@bengolddesigns9343 Thank you! and great job on the build! I am using it for inspiration.

Thanks very much. I got the battery box from RS Components. Here is the link to the one I bought: nz.rs-online.com/web/p/general-purpose-enclosures/7721101

Hi, thanks very much :) Sure, I use Esun carbon fibre nylon for the propulsion unit, Esun PLA+ for the Propellor and some of the hand control (black parts) and ICE PLA for the propellor duct and the hand control. Cheers

@@bengolddesigns9343 Thank you very much. I have already choosen a nylon filament. Another question: Can you recommend any wather protective spray or resin for 3d printet parts? Or generaly a spray that protects 3d parts from outdoor applications? :)

@@NicolaGrossenb876 No worries. I used a spray type resin called Nyalic, which I have found works really well. Epoxy resin is also really good but more work to put on. Here is a link to the website www.nyalic.co.nz/ :)

ciprian ionut thanks :) I the motor is a sss56104 480kv motor. I bought the battery box off RS components

@@bengolddesigns9343 thank you very. much RS components . Can I find it online?

Thanks mate. I’m in Balclutha. Do you think you will do a build video? Would love to see your build when it’s finished.

Yea I’d be keen to put one together, I’ll link here of I do

Thanks, I was using 4x11ah 6s Lipos but one of them malfunctioned. I’m in the process of building an 18650 pack for it at the moment.

@@bengolddesigns9343 hello, i would really like if you could get me a link where you bought battery! Thank you

Thanks :) I can try to put together a list of materials when I get a chance. I will send the link once I have it done

@@bengolddesigns9343 Hi Ben nice video, do you mind sending me that list too? Thanks :D

Hi, I originally had a 22ah of LiPo packs running at 12s which would give about 15 minutes of ride time. One of my LiPos has now failed so I am in the process of building a 12s 10p lithium ion pack which should give close to 25 minutes of ride time. Cheers

I saw a guy use a gun/ ammo box.

Hola, compré la caja en rs-online.

Hi mate. I use this EPS from Bunnings. I bought the densest one they had available. Bought to 80mm sheets and glued them together. www.bunnings.co.nz/expol-thermaslab-s-grade-2400x1200x-60mm-polystyrene_p0717381

Hi there, sorry still haven’t had a chance to make a riding video yet, I have been busy with a house build lately so haven’t had the time. I will definitely post one when I can. I am in New Zealand, I can send you my email address if you would like? Thanks :)

@@bengolddesigns9343 yes please reach me at jetsurfingnation@gmail.com

Hi, I don't have much video yet sorry, I am planning on doing a riding video but haven't had the time lately. One of my Lipos has failed so I am also building a new Li ion 18650 pack for the E Foil. There are a couple of photos of it on the water in the link from the first test. drive.google.com/drive/folders/1gRtezZojZv8ouOLLGDtcKCZrnHeaHYTY?usp=sharing

It is very hard to get the needed torque from such a small motor

Thanks :) I have put a link to the board fusion 360 file. I used the sketches of the plan and profile and printed at full size to cut out the polystyrene. I then shaped the rails to give them the rounded profile that I wanted. Hope this helps. a360.co/3eyW8TV Cheers

@@bengolddesigns9343 thnx!!!!!!!!)) I want to finish the sketch so that I could send it directly to the CNC machine (milling cutter). the dimensions for the battery compartment fit completely? it remains only to understand how much to make the rounding on the sides :)

@@akaZarj No worries. I have updated the battery compartment from that model I sent I think. I ended up making the compartment to fit the access hatch. I used this hatch www.burnsco.co.nz/access-hatch-596-x-348mm-large It does get the occasional bit of water getting in, not too much but I have made sure all my batteries and electronics are in separate boxes. Hope this helps :)

Hi there, yes fibre glass with epoxy resin for the board

He used autodesk fusion 360, i think there is a free non commercial license available for it. Else it is just 45$ per month

Hi Thomas, please see link. Thanks, Ben: www.printables.com/model/294714-e-foil-remote-control

Yavuz1773 I sanded the prints to get them as smooth as I could and then sprayed them with a polymer coating called Nyalic. You can buy it in a can. I’ve found it works really well with 3d prints. I tried my prototype on the water but haven’t had a chance with this one yet, hopefully very soon. I will make another video of riding

Hi there. Will get one sorted when I get some free time. Cheers

Hola, compré la caja en rs-online.