I appreciate that this is entirely done with circuitry and doesn’t require any micro controller or coding
@mariokutnjak74772 жыл бұрын
Hahhahahha
@forrest28518 ай бұрын
Although a MCU could help with timing…. Like keeping on the electromagnet on longer than the photoresistor is activated. Great Scott has a great video on the pros and cons of traditional circuitry vs Arduinos, builds an electromagnetic launcher with a MCU and without as an example. Very similar project.
@clementpoon1207 ай бұрын
@@forrest2851a capacitor would probably work as well
@RoycoNL7 ай бұрын
@@forrest2851 You can totally do that with analog components as well but Microcontrollers are just much easier to use in most cases.
@forrest28517 ай бұрын
@@RoycoNL Yes I know I am advocating for the use of an MCU.
@greggoog75597 ай бұрын
The only channel on the internet that's using a WWII microphone that still works!
@axontech2 жыл бұрын
All of your videos are outstanding - I have watched them multiple times. I really appreciate all of your high quality work not just on the videos but on your electronic theory based projects and explanations. I can't get over your using transistors to build a binary adder. I would have used TTL logic gates - but your expertise is way beyond what I know.
@topherteardowns4679 Жыл бұрын
someone probably mentioned it, but, your mosfet may have been blowing because the gate was only being fed 6 volts at the moment of trigger, which isnt fully turning on the mosfet, that high drain-source resistance is no bueno when you are calling for ALL the amps you can muster. maybe use a buffer transistor and see if that helps enough to be able to use the capacitors again. That will help save your battery from being beat up too. Awesome videos dude, glad I found your channel.
@DAVOinIN2 жыл бұрын
This is quite fun. Contemplating building my own, but instead of just using a fixed delay between opto-sensor and coil-turn-on, use a variable delay that depends on the speed of the ball. This will allow higher efficiency energy transfer and could be pretty easily implemented by comparing each opto-sensor with the previous one.
@syntheticbananas65263 жыл бұрын
Very good quality video. Was surprised to see you only have 70 subs. Seems like the kind of video you'd find on a channel with 100k+
@HyperspacePirate3 жыл бұрын
I just started this channel a few weeks ago
@StormBurnX2 жыл бұрын
A year later and already at 20k, this is what happens when people make quality content :)
@gameboyv1790 Жыл бұрын
@@StormBurnX a year later and already 138k
@dhaarialshammri2195 Жыл бұрын
@@gameboyv1790 2 weeks later and already 144k
@arnevandaele8 ай бұрын
@@HyperspacePirate is the ball a magnet or is it from metal
@Twistedmetal-qe8kx3 жыл бұрын
Nice build, very cool to watch
@redsquirrelftw7 ай бұрын
This is pretty cool, could have fun with that making an elaborate "train track" system of balls, could even have diverters so they randomly take different paths. Light sensors to track where balls are and more coils throughout to boost or even slow down balls so they don't collide with others. Could be a fun project to tweak all of it.
@raymondmichael49872 жыл бұрын
I watched the second version of this and got really inspired, will definitely make one if I ever get my 3D printer
@youtuubaАй бұрын
Very nice video, explains things pretty well. The only thing I would offer a criticism on is the video's title, since by the normal definition, this is not a "ring accelerator". That name is usually given to devices that continuously accelerate something in a ring/circular path, achieving very high speeds, whereas this device only gives a little kick to the ball in order to keep it moving. Yes, it briefly accelerates the ball, but then the ball coasts the rest of the way. It is really just a novel implementation of a DC motor. I own a commercially produced product of this same kind, having six electromagnets distributed around the circular track. I have not attempted to reverse engineer the circuit on each of the circuit boards (each electromagnet has its own identical printed circuit board), but I did note which components are on each board, and from that I assumed that a simple circuit, nearly identical to what you came up with. I think that the only real differences between the two circuits is that A) the one I have uses an IR LED and an IR phototransistor, and a driver transistor (probably a BJT) between the phototransistor and the MOSFET's gate.
@chusdiaz91603 күн бұрын
Hermano!!! ¡Ya tienes una aceleradora de partículas cósmicas atósmicas ! ¡Eres la ostia! Novel seguro espero te den
@MaltWhiskey2 жыл бұрын
This will be a great toy for my cats, they will love this. Thanks for sharing, this is going on my todo list :P
@DittoPerson11 ай бұрын
Thank you so much, I'm going to use your circuit design for my own, it will use 4 coils instead and should reach speeds up to at least 32 feet per second!
@threatz18026 ай бұрын
This is an insanely cool project
@EfieldHfield_3773 жыл бұрын
I like it - made me smile. Good fun project.
@MathIndy7 ай бұрын
To help protect your FET from over-current you could put some resistance between the source and ground. This is called "source feedback" and it will work to turn the FET off when the current gets to be too high.
@Twistedmetal-qe8kx3 жыл бұрын
My cat would love this :)
@limboe60303 жыл бұрын
Really cool and great how you solved all the problems
@user-fd8lj7bt2wАй бұрын
You did very well Although I don't know what this is for, your technology is ready to be levied😊
@keithsadlocha11783 жыл бұрын
I love the compactness. Few questions, can you connect 12 coils in serial? Can you output or induce current to a secondary coil to create a magnetic field for levitation? Can you share a parts list for that beautiful driver which is like a work of art.
@HyperspacePirate3 жыл бұрын
Yeah, multiple coils can be used. In my video on version 2 of this device, i used 4 coils, but more can be added. The working concept is the same as a coilgun which can accelerate ferrous projectiles several hundred m/s. The coil could be used for levitation if it was powered by high frequency alternating current or driven by a position sensing feedback controller. As for the parts, you can pretty much use any MOSFET, and the trigger consists of generic resistors and an LED + photoresistor. There's no specific part numbers that are required to make it work, it's all very generic
@keithsadlocha11783 жыл бұрын
@@HyperspacePirate Thank you very much for the guidance and information. I greatly appreciate it :) God Bless
@tonytor537 ай бұрын
The ARV uses similar quartz ring, many more accelerating magnets. The content of the toroid are nanoparticles of ferrite,mercury neodymium 52 nanoparticles as well as cobalt in nano particles and Barium.The hard part is to pressurize the contents to 200,000 atmospheres. Once you get the mixture turning, as it accelerates it centers in the toroid and does not touch the walls. The mixture turns into a plasma . At that time a secondary coupled in the middle of the toroid gets electricity induced which will later bbe use for other purposes. Continue accelerating, and a corona effect will be formed. Accelerating further will cause a white glow to involve the toroid and extend outside the test bench . That is when the “magic” starts. If you have the toroid experiment setup on a piece of wood or metal, using a non ferric scale (I used a wood fish scale) as the white glow increases, the weight of the apparatus will slowly start decreasing. I managed 5-7% of weight reduction. One of the individuals who was watching me with a grin, explained to me that the white light is a field that in part or totally “hides” M from E=MC^2. Just rotating the field only goes so far Using capacitors one can make a modified Hartley oscillator that when tuned is able to completely hide the Mass of the toroid And attached vehicle to not only does it hide the mass, but it bends light around the object, therefore turning it invisible or somewhat transparent. The crafts currently made by a consortium of Boeing & Lockheed in Pasadena use toroids 10 meters in diameter! These are the flying triangles that are commonly seen. I had knoledge of the TR3-B which is the most common flying triangle see. It was able to “hop” short distances by bending space using a complex capacitor based mechanism that projected the field within line of sight. No, I am no longer pervy to the advances made in the last 30 years. Nevertheless 8:41 the new TR3-G is capable of transluminal travel by bending space over long distances. From 40,000Km above earth orbit to the Alcione Solar system in the Pleiades 240 light years away in less than 2 earth hours. You get there at the time you left. If you see a flying triangle in the sky notice the circle in the center with a white light; it looks like “an explosion that does nog go anywhere”. Too bad I was only a physician, not a physicist. So, this is all I can convey from my observations. BEST OF LUCK. IF I WAS ABLE TO MAKE THE DEMO MODEL WORK WITH ASSISTANCE, YOU HAVE THE MATH KNOWLEDGE TO TAKE IT UP TO HALF OR FULL SCALE! Also I recommend you watch Mark McCandlish presentations. He was “suicided” on April 21, 2021. I was a friend of his. Marc McCandlish Best of luck
@F1yb0y19863 жыл бұрын
Now add another coil on the other side! Or one every 90 degrees!
@HyperspacePirate3 жыл бұрын
Yep, planning to in a future video. Also going to run at higher voltages. Should be interesting
@LeonMatthews2 жыл бұрын
Very inspiring project! Thanks very much for the cool video.
@pauljensen66996 ай бұрын
If you adjust the EQ on your audio and cut out the higher high end frequencies and use a compressor/limiter to cut out anything below a certain decibel it will remove that fuzz on your voice tracks.
@abpccpba7 ай бұрын
Very nice work. Thanks.
@Public-Enemy-No.12 жыл бұрын
looks a little bit like a Searl Effect Generator. Cool work!
@chaselarson42247 ай бұрын
The future of hot wheels cars and their track set up🎉
@charles-antoinegagne6109 Жыл бұрын
Basically an homemade particule accelerator.
@AMDcore17 ай бұрын
Interesting to see if you could control the timing as the balls velocity increase so you can adjust the speed of the ball. Like the spark advance or retard timing on an internal combustion engine.
@hxlize4913 Жыл бұрын
youve given me the tools to build a particle accelerator
@peppeddu4 ай бұрын
You could have simplified the design by removing the optical sensor and checking for a micro-spike in voltage on the coil (as a sign that the ball is in range) then quickly power it up to attract the ball and then quickly powered it down to let it continue. In this way it would work for the ball coming in either directions. Nice idea though.
@ThaboW113 жыл бұрын
Good stuff.
@bennyellis3512 Жыл бұрын
He reminds me of a cat near the end of the video 😮Oooh dude I just had an idea; if you have cats in your neighborhood you should totally make one designed with a captive ball and show it to them and videotape it 😃
@rotten-Z7 ай бұрын
LHC - Little Hadron Collider?
@ostanin_vadym2 жыл бұрын
Thanks for the content
@TheExplosiveGuy2 жыл бұрын
I think it needs a capacitor, give each pulse a little more oomph and get that thing spinning around the table😉. It's halfway to being a toroidal coilgun anyways lol, at this point you might as well put a couple more stages with some electrolytic capacitors on it. Now that I think about it that would be a great way to fine tune the pulse timing and duration for a coilgun...
@HyperspacePirate2 жыл бұрын
That was actually the original intent of the project
@arnevandaele8 ай бұрын
@@HyperspacePirate what is the diameter of the ball
@HyperspacePirate8 ай бұрын
1"
@arnevandaele8 ай бұрын
@@HyperspacePirate what did you use as battery
@Geo42Geo7 ай бұрын
The principal of how your accelerator works is similar to partical accelerators. Very cool let me know when you make the god partical 😆
@maouplulax7 ай бұрын
Very cool you should try making one big enough to achieve relativistic speeds
@jgj6331 Жыл бұрын
Using a magnetic ball and a magnetic reed switch to control the coil, it may be possible to eliminate the electronics entirely and radically simplify the device.... Similarly, a steel ball and some light contact points that complete the circuit through contact with the steel ball....
@tomholroyd75197 ай бұрын
Very satisfying fun part
@brettmoore31942 жыл бұрын
Mass ×speed squared is where the excess energy occurs so one or both sides of the equations should.be optimized
@ManyHeavens422 жыл бұрын
Gaps are Bridges ! Bridges Are free energy.
@bartdelege9297 ай бұрын
Why not put the optical sensor a bit further from the winding, and use a 555or 551 timer? It would speed it up earlier and you can set the turnoff time. Fun project anyway!
@brettmoore31942 жыл бұрын
This is what scientists are missing. So have 33mile long counter rotating sphere tracks with anprojectile of neo of 66kg each. Once spead to the velocity of light then collide in an receiver area 7nit
@curiousviewer59913 жыл бұрын
Now to make a Minecraft-like roller coaster or marble machine a with coils as accelerators to keep things moving up inclines/long stretches and then gravity for downhill! Haha!
@HyperspacePirate3 жыл бұрын
Yeah, a roller coaster type device like that is definitely on my to-do list. Hopefully I can make some coils that are powerful enough to do a vertical loop too
@curiousviewer59913 жыл бұрын
@@HyperspacePirate That or several firing off in rapid sequence, one after another.
@circuitmage42403 жыл бұрын
@@HyperspacePirate This is good kit, all plastic. Took me 1.5 hrs to build. If I follow your lead, I will add coils to this and some other thingies. spacerails.com/products/sr-1-1
@atharvaasare731310 ай бұрын
Man took an angle from where the balls looking like f1 racers
@gamerdude422 Жыл бұрын
Now add 5 more coils and watch as the balls get faster and faster.
@beautifulsmall Жыл бұрын
The wedge coils are interesting, I wonder if an automatic coilwinder could wind such a beast.
@Primer5953 жыл бұрын
Put it on a slight incline to help the magnetic ball get through every time. A giant electronic trampoline is possible!
@mrguymanjr57776 ай бұрын
would be koool for hotwheel cars
@crackthefoundation_8 ай бұрын
When a cyclotron and a railgun have a baby:
@moguldamongrel30542 жыл бұрын
Using an electromagnetic acceleration gate would be interesting space tech for a non fuel dependent sling into the direction you wanna go. Build another gate on the other end to catch incoming traffic.
@HyperspacePirate2 жыл бұрын
you mean this lol en.wikipedia.org/wiki/Mass_driver
@moguldamongrel30542 жыл бұрын
@@HyperspacePirate aren't mass drivers to shoot unmanned projectiles at ridiculous speeds that would flatten a normal human with sheer g forces. And or a proposed way to launch material cheaply from one planet to another.
@moguldamongrel30542 жыл бұрын
@@HyperspacePirate no I mean a literal gate large enough to accelerate a space ship to it's receiver, without killing the occupants. If you mixed this with one dudes molten sodium experiment you'd have a starship with a magnetic field (rad blocker) and an acceleration gate (fast intra system travel). Using field manipulations you could have the receiving gate emit a repulsion field to slow the object in question on approach.
@moguldamongrel30542 жыл бұрын
@@HyperspacePirate kzfaq.info/get/bejne/qKeJipyfnc-Rc2g.html this guy's experiment
@DrKoneko6 ай бұрын
I need to see it overclocked. I want a mini particle accelerator.
@ManyHeavens422 жыл бұрын
Ha here's a hint, what kind of Flashlight recharges itself by shaking it up and down , Hahaha you got it , a caveman flashlight
@seanvandiijk2889 Жыл бұрын
Who else has found for the first time that an electric motor is no different than the working principle of a piston engine? All electric motors are Alternating Current motors, without AC, the rotor is just going to get stuck in the magnetic field, so the commutator is the equivalent of the valves of a piston engine, more or less.
@bwygo5 ай бұрын
I feel like you could use this to make trains travel
@bwygo5 ай бұрын
Also is there not a way for the balls the recharge the battery via the Kenetic energy
@hardcoregaming41182 жыл бұрын
hii i m from India bro you are grate this project make free energy my special project is my own mini spaceship to use the project for a free energy and my space is best but u don't known i really make this my project basically my project is travelling to space it real in future
@UTKETCHUP2 жыл бұрын
Ah yes the troll
@asusasus23002 жыл бұрын
merci , super projet ...
@isocle6 ай бұрын
Neat! Wonder if you can detect changes in the load and switch the circuit off based on that instead of the optical sensor.
@Teyros7 ай бұрын
Pretty cool! :)
@joaonunes603 Жыл бұрын
😮how many meters of wire will go on the spool?
@jamesmatheson9624 Жыл бұрын
needs to be put in outer space so when space crafts can goes though it, it will accelerate the spacecraft without the spacecraft having to use energy and whatever speed it can achieve the spacecraft will be able to continue at indefinitely, i suggested 64,000 km an hour which will get people to the moon in 6 hours, that might not be possible but there is a speed that can be done that will work ,
@Manhwaseek21 Жыл бұрын
How can i contact you? We want to buy your project 😅🙏
@benjackson97362 жыл бұрын
Hi, do you have the STL file for the side clip that holds the LED and photoresistor? I don't think that one is on the thingiverse page. Thanks I love this build and the elegance of the design
@kotelypiesely12688 ай бұрын
this is the basic setup for a coilgun, but a spinny marble tumbler is also fine I guess
@giulianosteifn3 жыл бұрын
The same principle of the CERN Particle Accelerator
@cliffwilson21712 жыл бұрын
Great project! Do you mind sharing the LED and photoresistor bracket stl? They are not in the Thingiverse files. Thanks!
@charlesmanning34547 ай бұрын
It's momentum that keeps the ball from getting stuck in the center of the coil, the more the better. I wonder of tilting the track a little bit so the ball had some gravitational acceleration going through the coil, would that reduce the chances of getting stuck? Or would the problem become not making it up the slope after the coil?
@7ooligan8339 ай бұрын
Hey, I have a question, at the beginning you say that the 4 AA batteries did not work, but at the end of the video you no longer explain that part, I understand that you used approximately 12V and 6A, but if you did not use the batteries, where did you get the energy from? I mean, what type of battery or source?😅
@jerryfreeman85872 жыл бұрын
Please incorporate an alternator type element on a large scale model
@davidcorraleszambrano35232 жыл бұрын
Hi man I love what you did! Question do you have a picture on how you connected everything on the other side? I appreciate it man
@HyperspacePirate2 жыл бұрын
What do you mean? Underneath the circuit board?
@FB-wj4yu2 жыл бұрын
@@HyperspacePirate yes
@jfn4823 жыл бұрын
Why couldn't you try to reclaim some of that inertial energy by having the balls travel through coils that generate electricity and even perhaps trickle charge the original power source?
@HyperspacePirate3 жыл бұрын
That could work if the balls were permanent magnets, but in this device I'm using steel, so they're only magnetized when they pass through the accelerator coil
@aanyasingh72472 жыл бұрын
hey man that was so great can you please tell me which app was that from which you were demonstrating
@artsergo2 жыл бұрын
But if you use 3 magnetic balls for the ring? at the same time, if you use two coils with capacitors of 10.000 - 20.000 uF to save the electrical impulse (for the further movement of the ball without stopping). maybe even try to do it more broadly? those. use many coils, but each 1, 3, 5, 7, 9, 11, 13 coils with a capacitor, but each 2, 4, 6, 8, 10, 12 coils will be connected in series and used to select, generating electricity. so can you try it? but the balls appear to be magnets. ----- Or maybe even all capacitors connect use diodes but only in the same direction
@777redhood Жыл бұрын
Thats pretty cool..i did not understand the diagram..and how the circuit board works..could you please guide me to some resources that would help me understand this better..i have no idea what to Google search
@GTvideoHD2 жыл бұрын
Which thickness (diameter ) of cooper wire did you used?
@SupremeKingSovereign6 ай бұрын
3D printers really changing things for the better.
@thijsbeentjes38013 жыл бұрын
how did you connect the LDR so far from the board? And is this possible to with a breadboard and Arduino?
@HyperspacePirate3 жыл бұрын
It's just 24 gauge wire running to the LED and photoresistor. Not difficult at all. You can definitely do this with an Arduino
@pauliexcluded17 ай бұрын
You didn't share the STL file for the diode holder.....
@fitnessnature7 ай бұрын
you made mini universe
@sillybears46732 жыл бұрын
Could you build a track same design but utilize the tracks surface as part of the circuit and use multiple electromagnets in segaments around the track that get activated when the magnetic ball passes by and completed their individual circuit propelling the ball through angled electro magnets that look like arrows going in one direction around the circle with the leading end being closer together like I see people doing in other videos but it shuts off halfway through the magnetic fields perfectly timed and doesn’t get stuck and actually shoots off would you be able to build sustainable torque in a circular shape design with multiple magnets all turning on as the ball completes each individual circuit along the track as it passes by maybe with some sort of insulated strip of copper along the botttom for isolated contact but Anywyas do all that and get these balls flowing super fast and build up torque then use that torque to charge the battery that’s powering the electro magnets? Maybe my question is a bit convoluted, I apologize. but I feel like the amount of energy to power the magnets gets less as it gets faster but also turns on more times then it would if it was spinning slower but I’m wondering if short bursts with building torque can equal over unity if even slightly in that hypothetical configuration.
@THE_WIN710 ай бұрын
Hi, can I ask, can we not use the circuit, so we turn it on and off manually by connecting and disconnecting the electricity?
@Jkauppa2 жыл бұрын
make it dc acceleration track instead, and you can use carbon as conductive contact lubricant, dc lorents force, the track is the brush that make the ball the line conductor, ie, curved rail gun, dc, brushed, could be brushless if the circular-radial magnet is the projectile, coils around the track tube, air bearing
@Jkauppa2 жыл бұрын
if you use plasma high voltage to jump the wall-ball gap then you have a kinda plasma brushed motor
@Jkauppa2 жыл бұрын
continuous acceleration vs pulse coil gun ring
@Jkauppa2 жыл бұрын
same for plasma ions acceleration ring, where the ions roll around the ring track
@Jkauppa2 жыл бұрын
maybe keep the outside diameter positive so that the track forces the ions to stay inside (or on the outside) against or with the centrifugal force, whatever design suits the wanted functionality
@_next223 Жыл бұрын
does the device use the same amount of energy regardless of the the type of ball in there? between stainless and the magnetic ball is it the same?
@pertevdural45133 жыл бұрын
large hadron collider!
@jackskidoo10052 күн бұрын
Whats the diameter of the steel ball you used?
@cruelai282 жыл бұрын
Hi! I know you might not get to this comment, but I was wondering what materials and wires you used in the middle. I already have the female JST, opto sensor, and led's, but I can't seem to find the rest. I'd greatly appreciate it if you could reply to this comment. Good job on the project!
@HyperspacePirate2 жыл бұрын
The pieces are 3d printed and snap together with magnets. The board is just cheap perfboard
@Terinjim Жыл бұрын
What if you add the same @180° (coil) then use steel ball then a magnetic ball then use variable voltage to control the rate?
@patty19917 ай бұрын
😮 make it faster, and faster, than open a way to outside and you have a gun -> like CERN
@Mbb222010 ай бұрын
Hey, photoresistors are hard to find in my area. Could i replace it with an ir led and those black ir photodiodes?
@sehun_life Жыл бұрын
May I know the names of all the parts you need to make this?Please write as many details as you can
@eaa115 ай бұрын
Hi, I couldn't understand why the ball oscillates when we give constant power to the coil (3:20). I would be glad if someone could explain it to me.
@ahsanahmedbhaila4 ай бұрын
When we power the coil it creates an electromagnetic field and acts like a magnet. When we put a ball, it gains kinetic energy from the magnet. The ball will then exit the coil, but the magnet is still on, so it will get pulled back until it rests in the middle. That’s why we turn it off.
@ashwanthkumar.s782410 ай бұрын
Without the opto sensor can this work with a magnetised ball that you used
@thijsbeentjes38013 жыл бұрын
Good video! Is it possible to buy a switch wich is activated when the light is interrupted, like yours? I want to try it for myself
@HyperspacePirate3 жыл бұрын
I'm not sure where to find them as packaged units, but it was very easy to build. I just used an LED and one of these photoresistors: www.amazon.com/MCIGICM-Photoresistor-Sensitive-Resistor-Dependent/dp/B07PF3CWW9/ref=sr_1_3?dchild=1&keywords=photoresistor&qid=1624025077&sr=8-3
@thijsbeentjes38013 жыл бұрын
@@HyperspacePirate Thank you, not very experienced with this, you attached it to the board where it lets electricity trough, I think you made it yourself right? Or is it possible to get that somewhere
@HyperspacePirate3 жыл бұрын
@@thijsbeentjes3801 i soldered the parts to perfboard which is just a grid of holes with copper plating around them. I use this, but there's thousands of other options out there that work just as well: www.amazon.com/AiTrip-Perfboard-Breadboard-Prototyping-Electronic/dp/B07XYL451Y/ref=sr_1_3?dchild=1&keywords=perfboard&qid=1624026067&sr=8-3
@thijsbeentjes38013 жыл бұрын
Thanks you so much, appreciate the help. Found out that the word is relais. Looking for buying one like the whole thing. I can’t put it together myself
@jussikankinen94096 ай бұрын
Copper is magnetic when moving
@tonysfun3 жыл бұрын
OK, I've printed all 4 parts with the 4 coile option. How would I wire all 4 coils? I'm sure I can't just connect them all paralel ! Anyway, thanks again for the STL files!
@HyperspacePirate3 жыл бұрын
The high sides are all connected to VCC (12V in my case) and the low side of each coil is connected to the drain pin of its own MOSFET (i use an IRLZ44 in this case, but there's lots of others that will work). Remember to connect a flyback diode across each coil with the cathode *FACING VCC*, or else the inductive spike from the coils will cause a voltage spike that will destroy the whole circuit
@dikrusyt73378 ай бұрын
coil size (thickness of wire)
@DCray-fv7gf4 ай бұрын
@HyperspacePirate how do u create 6 amps of power without using capacitors
@ardhi12693 жыл бұрын
So is this the simpler version of electron accelerator
@nestaismail91894 ай бұрын
This would be impressive if it had NO POWER SOURCE , you literaly have a power source to turn on the coil.
@hvhgdfgyffghhgd46634 ай бұрын
how else are you supposed to turn on the coil?
@ahsanahmedbhaila4 ай бұрын
Then how do u power the coil? Free energy doesn’t exist.