Electronic Indexer for Milling Machine
Рет қаралды 58,756
2 ай бұрын
@stewartfrye 2 ай бұрын
Great work, sorry the safety crew showed up in the comments, the righteous are everywhere. Thou shalt not enjoy your own shop and your own tools you made! And a great video to boot.
@chucksmalfus9623 2 ай бұрын
What did you use for the controller? Can you show parts list and explain software
@kvechannel 2 ай бұрын
Is a atmega1284 controller and the pulse train for step motor created by timer interrupt. The board is a general development board. Is my own design with easyeda and manufactured by jlpcb.
@rcon8017 2 ай бұрын
Very nice work!!
@kvechannel 2 ай бұрын
Thank you!
2 ай бұрын
Szuperek ezek a videók. A marógépedről is csinálhatnál egy részletesebb bemutatást mit mivel oldottál meg.
@kvechannel 2 ай бұрын
Köszi, lesz majd talán egy végleges bemutató videó mert eddig csak részletekben sikerült valamennyire mivel állandoan fejlesztem, cserélem az asztalt, fejet stb. Jelenleg a harmadik asztalnál tartok és a harmadik fej modosításon vagyok túl :D Talán ez már végleges kielégíti az igényeimet egyelöre..
@kwissiekwissie 2 ай бұрын
NICE WORK!!!!
@kvechannel 2 ай бұрын
Thank You!
@minasianjohn 2 ай бұрын
Is it possible to use Mach 3 to program the rotary table? If not can I buy the plans for making the programmer.? Thx
@kvechannel 2 ай бұрын
Is not possible to use with Mach 3 but is a good idea for future development. Sorry I not selling plans.
@liboy34 2 ай бұрын
Hi Good job.
@ismailhakam2957 2 ай бұрын
Nice job body
@brilloestelar1 2 ай бұрын
Hi. Congratulations for your youtube channel and for this video. Please, could you tell me the model and brand of the stepper motor? Thanks in advance.
@kvechannel 2 ай бұрын
Thank You! Is a Stepperonline 4Nm Closed Loop Stepper Motor Nema 24 with CL57T driver
@brilloestelar1 2 ай бұрын
@@kvechannelThank you very much!!!!!
@brilloestelar1 2 ай бұрын
Hi, again Kvecahhel. After seeing your video, I have decided to motorize my rotary table. Please, could you tell me the brand and model of the display, the keyboard, and the software...? Also, where can I get them? Thank you very much.
@ronaldlabiche2049 2 ай бұрын
Not a good idea to operate a lathe with long sleeves
@chucksmalfus9623 2 ай бұрын
Or hold parts by hand while drilling when there’s a vice right there 😢
@stewartfrye 2 ай бұрын
are you his momma ?@@chucksmalfus9623
@stewartfrye 2 ай бұрын
are you his momma, your addressing a grown man in his shop, not yours
@minasianjohn 2 ай бұрын
He is over eighteen ...@@stewartfrye
НОВОСТНИЧОК
Рет қаралды 16 МЛН
kvechannel
Рет қаралды 56 М.
Myphoneacc
Рет қаралды 11 МЛН
Photographer Army
Рет қаралды 2,3 МЛН