Homemade DC/AC Oscilloscope Current Clamp | Hall Sensor + Ferrite Core

  Рет қаралды 118,188

Electronoobs

Electronoobs

Күн бұрын

🔥The clamp works perfect but is not the most professional tool ever, it is more as an example in order to understand the theory. You could always improve it using better OP AMP and a better circuit. It could observe both DC and AC currents with a range up to 9A. I hole you like it.
🔀LINKS
-------------------------------------
Full part list: www.electronoobs.com/eng_circu...
Schematic: www.electronoobs.com/eng_circu...
3D STL files: www.electronoobs.com/eng_circu...
AC clamp: www.electronoobs.com/eng_circu...
DC clamp: www.electronoobs.com/eng_circu...
DC compensation: www.electronoobs.com/eng_circu...
Arduino multimeter video: • Arduino based current ...
Keysight channel: / @keysightlabs
🤝SUPPORT
-------------------------------------
Join my Arduino Course (Spanish): bit.ly/2JY8icE
ELECTRONOOBS.io: electronoobs.io
Help my projects on Patreon : / electronoobs
my Q&A page: electronoobs.io/forum/index.php
Facebook page: / electronoobs
Canal en Español: / electronoobs en español
00:00 Intro
00:33 How to measure Current
04:07 Probe Teardown
07:20 DC current probe
09:55 Homemade Probe
12:47 Schematic
13:08 Calibration
15:25 Thank you
Like share and subscribe to motivate me. Thank you
#current
#clamp
#homemade

Пікірлер: 137
@ELECTRONOOBS
@ELECTRONOOBS 7 жыл бұрын
I hope that you'll enjoy this video. If you have any question or maybe a improvement just live it in the comment section here. Visit my webpage for more. Also, visit my Pateron site if you would like to help me. Thank you.
@UndernetSystems
@UndernetSystems 6 жыл бұрын
Gracias hermano, hermoso video!
@thecombatengineer7069
@thecombatengineer7069 5 жыл бұрын
I would suggest that anyone who builds this makes sure that get a LINEAR OUTPUT Hall Effect Sensor. Something like the A3114 Hall Effect is a fast-switch and only goes high or low, so it wouldn’t work for measuring linear increases. I tired it and failed. No worries, I’ll get some SS49E or similar Linear Output Sensors. Great job and thanks brotha!
@anthonycalia1317
@anthonycalia1317 6 жыл бұрын
Excellent video. Your ability to explain the concepts and circuits was exceptional. I hope to see more of your work.
@jimwyt
@jimwyt 4 жыл бұрын
What a wonderful, creative, low cost hack! This is exactly the basis I needed for a non-invasive high current monitor for a battery back up sump pump. Thanks so much for sharing!
@qps9380
@qps9380 7 жыл бұрын
So good man! I've always wondered how the current clamps worked!
@SteinErikDahle
@SteinErikDahle 7 жыл бұрын
Awesome video! I actually learnt something new today about DC-clamps! Thanks!
@ELECTRONOOBS
@ELECTRONOOBS 7 жыл бұрын
U wellcome, I'm glad to hear!
@sincerelyyours7538
@sincerelyyours7538 6 жыл бұрын
I was looking for a current probe like this not long ago but gave up due to the high prices. This one is quite possibly the ugliest looking probe I've ever seen, but that's OK because it obviously works! Why should I buy a probe costing hundreds of dollars when I can now easily build my own for dirt cheap? I learned something today. Great job, and I look forward to seeing more from you!
@robotronix-co-il
@robotronix-co-il 5 жыл бұрын
Tank you for the Excellent video , you just save me few days of experiments in the lab
@agaelema
@agaelema 7 жыл бұрын
Awesome project! I Will follow this video and mount my own diy current probe . Thanks for share
@ryanshelton4545
@ryanshelton4545 4 жыл бұрын
I loved this video. Thank you for sharing, you're a great teacher.
@lonniebates1533
@lonniebates1533 4 жыл бұрын
Best explanation I've seen of a dc current probe.
@danielolmo9625
@danielolmo9625 6 жыл бұрын
Nice video! It's been a while since I've been looking for this!
6 жыл бұрын
Excellent video! Thanks for explanation! I have a Unit 201E and i will try to modify it to add a analog output. Many thanks!
@MrRonychakraborty
@MrRonychakraborty 6 жыл бұрын
You are the Boss. You saved my time a lot thanks.
@elson2k
@elson2k 3 жыл бұрын
Nice video ;) I was just searching for an easy way to measure and observe currents via oscilloscope and your solution gave me some ideas. Thanks! :)
@WaltonPete
@WaltonPete 6 жыл бұрын
Excellent video! Love the project idea - some AC scope clamps can cost as much as a budget DSO! Great explanation and implementation of cheap, easy to source parts.
@ELECTRONOOBS
@ELECTRONOOBS 6 жыл бұрын
Pete Allum thank you very much! Keep up!
@Seshagopalan967
@Seshagopalan967 6 жыл бұрын
Once again, you made my day!
@AB-yu2tj
@AB-yu2tj 4 жыл бұрын
It's good short and to the point. Thank you
@charvakkarpe
@charvakkarpe 4 жыл бұрын
Wow, one of the best technical videos I've seen on KZfaq. You clearly have a solid understanding of physics and electronics, cover content at the right pace, include the right video shots and animations. I liked the B-field overlay on the magnetic core, with the X showing current flowing down and the arrows spinning clockwise. I'd love a follow-up video with details on the Hall effect, and a demonstration of what happens if you move the wire around within the ring. I suspect something like Gauss's law says it doesn't matter where the current is inside the ring, but clarification would be great. I'm about to go look it up for myself.
@charvakkarpe
@charvakkarpe 4 жыл бұрын
Found it. It's called Ampere's Circuital Law. The line integral of B-field along a loop is proportional to the current it encloses. I had pictured an entire array of Hall-effect sensors inside one of those current clamps, but using a ferrite core to capture the field and force it through a single Hall-effect sensor makes sense. en.wikipedia.org/wiki/Amp%C3%A8re%27s_circuital_law#Explanation
@brujo_millonario
@brujo_millonario 5 жыл бұрын
Thank you, I've learned a lot.
@hebrewhammer1000
@hebrewhammer1000 5 жыл бұрын
Thank you for sharing. Great video.
@FreeCircuitLab
@FreeCircuitLab 2 жыл бұрын
Nice video brother! You should regulate the supply voltage because the output of the sensor depends on the supply. And also you have to use two potentiometers, one for zero adjust, another for calibration. Zero adjust is needed because the sensor outputs half of the supply voltage at zero field. We have to get rid of that first
@artiomoable
@artiomoable 2 жыл бұрын
Thanks. good video! What max AC frequency it can measure?
@warshatube
@warshatube 6 жыл бұрын
thank you so much sir, I have question if I make the DC amp clamp without the amplifier can it measure high DC current (300-400 amp)
@JAKOB1977
@JAKOB1977 5 жыл бұрын
"You know nothing John Snow". (thats how i feel when watching some of these aspects in this video.. yeah my mindset is pretty limied when it comes to electronics but I do like my current AC&DC clamp meter 210E. Im such a noob I actually thought these big clamp meters was for batteries and often was puzzled why they didn't open up wider and was supprised when i finally realized you could measure current without toggling physically onto the circuit..) thx for the vid.
@sereenasonya
@sereenasonya Жыл бұрын
Well done Brother. Loved it.
@wgm-en2gx
@wgm-en2gx 6 жыл бұрын
Nice explanation. thanks.
@lalmuanpuiamizo
@lalmuanpuiamizo 7 жыл бұрын
Nicely done
@sylvainlazare1114
@sylvainlazare1114 6 жыл бұрын
Thank you! I hear for the first time the principle of DC clamp probe. My question is how sensitive is it ? commercial clamp probes are sensitive to
@bigt121947
@bigt121947 6 жыл бұрын
thank you for your time.
@georgedsuarez
@georgedsuarez 6 жыл бұрын
Excellent video!
@Taran72
@Taran72 4 жыл бұрын
This project is really awesome and yes, I've found out what to do with a bunch of half ferrite cores I got :) . I think that the improvements can be made with the amplifier circuit and the calibration...but you speak of the AD623 in your video on current sensors....can I use the AD623 for all these type of projects related to probes or instrumentation circuits? I'm not that familiar with OPamps.
@eletronicaautomotivadicass5520
@eletronicaautomotivadicass5520 3 жыл бұрын
Ótimo vídeo. . esse projeto substitui todas as funções do cc65? Posso usar no ramo automotivo?
@lupoal4113
@lupoal4113 9 ай бұрын
bravo! very useful video! about the "better" op-amp... do you have any suggestion?
@polkijain97
@polkijain97 4 жыл бұрын
Hi. Great explanation of the amp clamp. Can you point to any off-the-shelf component to integrate into the circuit that can measure 10A to 150A linearly and give millivolts as output to be read through an Arduino or any other microcontroller?
@next8226
@next8226 6 жыл бұрын
Love ❤️ your all videos you grate😍😍😍😍😍😍😍😍😍
@satviksharma3722
@satviksharma3722 3 жыл бұрын
This was a great video!!
@FyaaahS
@FyaaahS 6 жыл бұрын
Awesome video!!
@johnconrad5487
@johnconrad5487 6 жыл бұрын
i enjoyed the video. the frequency response is very low. did you try to speed it up in any way? perhaps by adding a small cap... maye 100 pF across the input 1K resistor. it may help
@zikermu
@zikermu 3 жыл бұрын
Thanks a lot for this great educationnal video .
@crtsuznik
@crtsuznik 5 жыл бұрын
I'm surprised you didn't burn the sensor. The datasheet says it's operating voltage is between 3.0 and 6.5V
@Slic-Rock
@Slic-Rock 5 жыл бұрын
Hi nice video, what current clamp can you recommend for Fluke unit. Their clamp are expensive and have for 1mV DC = 1Amp DC and 1mV AC = 1Amp AC. I would like to find affordable clamps for Fluke 124. Thank you
@vysakhav
@vysakhav 6 жыл бұрын
Thanks ,very helpful
@jezzapimp
@jezzapimp 4 жыл бұрын
Awsome project! What sort of bandwidth do you get with this unit?
@mojtabajamal3457
@mojtabajamal3457 4 жыл бұрын
very nice ...thank you
@kostaslaza12
@kostaslaza12 6 жыл бұрын
awesome keep going!!
@kac3514
@kac3514 4 жыл бұрын
Can this work with multimeters that have this function
@viekynajoan1520
@viekynajoan1520 4 жыл бұрын
Any recommended hall eff. sensor ? Thank you in advance 🙏🏻
@qzorn4440
@qzorn4440 Жыл бұрын
A most excellent current clamp circuit. Do you have any suggestions on an clamp-on current circuit on a 2,300 volt AC wire? 😎 Thank you.
@ednja
@ednja 3 жыл бұрын
Can this clamp be plugged into a multimeter instead of an oscilloscope? What is the maximum DC current it can be used to measure?
@lenaroseguera1241
@lenaroseguera1241 6 жыл бұрын
I read that the maximum supply voltage for the 49e sensor is 6.5v. how can you supply it with 9v?
@apurvakalvade2301
@apurvakalvade2301 5 жыл бұрын
In case if we don't want to use BNC connector and want the reading on the LCD _ then if we directly connect the output of the OPAMP to the LCD, will we able to get the display of current ratings on LCD?
@ronniepirtlejr2606
@ronniepirtlejr2606 4 жыл бұрын
When measuring DC, could it be possible to design a circuit and not use a hall sensor? Maybe something that pulses AC (low voltage of course!) Then design a small circuit that can calculate the difference in current/ resistance in dc? I'm really new to electronics I'm trying to learn schematics, chips & components Etc. I realize the hall sensor is pretty simple. I just want to know if it's possible?
@UpcycleElectronics
@UpcycleElectronics 6 жыл бұрын
4:53 ...is not a transformer in the classical sense. It's a choke used to reduce/filter back emf noise from the device and prevent it from returning to the mains line ;)
@chuckthom7012
@chuckthom7012 5 жыл бұрын
What do you think about using a clamp off an old timing light?
@ihabhamad8290
@ihabhamad8290 6 жыл бұрын
you are a perfect man :)
@alfredseaman2796
@alfredseaman2796 5 жыл бұрын
Thank you so much
@janoschlolmann8822
@janoschlolmann8822 6 жыл бұрын
Very nice video, but there is still one Question: You said that the LM324 is a bad operational amplifier, why dou you think like that and which one would you recommend ??
@johnconrad5487
@johnconrad5487 6 жыл бұрын
there are many op amps that are much faster... the LM324 is old and slow.
@loulounet777
@loulounet777 6 жыл бұрын
LM324 is basically four LM741. and we all know the 741 is an old thing. amazing at the time but way passed and very very slow. a better "general purpose" opamp nowadays would be the TL071 from texas :) very cheap :)
@garethronaldo8692
@garethronaldo8692 6 жыл бұрын
Nice
@asmarahman9291
@asmarahman9291 4 жыл бұрын
Hello I'm student from University Putra Malaysia from Malaysia. May I ask, for DC Current Clamp Meter, is it just hall effect ic and ferrite core only or u need copper coil around the ferrite core?
@yoramstein
@yoramstein 6 жыл бұрын
Hello mr.Electronoobs great videos you make. Just wanted to ask what 3D printer did you use to make the case for this probe?
@ELECTRONOOBS
@ELECTRONOOBS 6 жыл бұрын
In that time of the Year I was using my Anet A8. Keep up!
@sayantanmaiti2513
@sayantanmaiti2513 6 жыл бұрын
Sir can you please explain a little bit why did you used that potentiometer with the opamp and why you preferred the inverting configuration of opamp?
@sonyobright2106
@sonyobright2106 5 жыл бұрын
the 49e hall sensor has a bias voltage of half the power vcc ... means that the hall sensor would output a 2.5 v for a vcc= 5v with NO magnetic field sensed by the sensor ... the potentiometre help to offset that bias voltage ...the inverted configuration help for the gain. in this case 100. witch is too big in my opinion .. a gain of 10 will be more than enough.. another strange thing is the 9v battery that is too big for the sensor. in the end the filter is wrong and not suitable for this ...good work
@DavidLeeMenefee
@DavidLeeMenefee 7 жыл бұрын
Nice video. Thumbs up...PEACE
@SianaGearz
@SianaGearz 6 жыл бұрын
Small planet, eh?
@ikkeslim007
@ikkeslim007 6 жыл бұрын
Is there a way to make it usable to measure currents up to 70-80 amps or more? Maybe with a switch for high/low amp range? I'm really interested in making one, but i would like to measure more than 9amps! It's an relative easy to understand schematic, really love it!
@CheapskateGarage
@CheapskateGarage 2 жыл бұрын
He's using an amplifier to bump the sensitivity up to 1V/A. You need yours to be less sensitive. You could scale the gain down to ten (he used a gain of 100). Or, you could leave out the amp and see where that gets you. Experiment measuring a known current and see what your sensitivity is.
@itsmekennyd
@itsmekennyd 2 жыл бұрын
thanks I really need to make 2000 amp one could you help?
@waqaszahid86
@waqaszahid86 5 жыл бұрын
I am in the middle of building something similar but it is exclusively for measuring AC currents, I am using a self made current transformer with two pair of windings, after building the amplifier circuit and extracting the RMS value in a manner similar to what a non true RMS DMM does I have realized that the self made transformer with toroid core from atx power supply is very non linear and i am still struggling to find a method to resolve this problem.
@morbitalok
@morbitalok 6 жыл бұрын
how to easly adopt to 40 mV/A ? anyway great thng and movie!
@tiagonet8794
@tiagonet8794 2 жыл бұрын
what modification will you have to make for measure 1000A or 5000A?
@MrBreak745
@MrBreak745 6 жыл бұрын
can you make BMS circuit for 3 li-ion battery pack > it would be a great video
@anukeshambatkar6255
@anukeshambatkar6255 4 жыл бұрын
Sir can you please make a tutorial on wcs1500 current sensor which is of 200A capacity
@devilvortex1
@devilvortex1 4 жыл бұрын
can I calibrate the clamp 1A and set the output to 0.1v?
@borisivanov1175
@borisivanov1175 4 жыл бұрын
What if I need to measure 2000-3000amps? How different it make such device?
@ghamor7590
@ghamor7590 7 жыл бұрын
thank you very mach
@hannnnn310
@hannnnn310 6 жыл бұрын
Hi! May i ask?...How high is the max frequency of the current clamp could measure?
@ELECTRONOOBS
@ELECTRONOOBS 6 жыл бұрын
Hi there. Can't remember for sure. The max freq is given by the max freq of the OPAMP and the Hall sensor. Just check those datasheets. Sorry. Keep up!
@mohammadqz8956
@mohammadqz8956 4 жыл бұрын
can I make one with an accuracy of 1mili-amps like this?
@antontaranov533
@antontaranov533 7 жыл бұрын
отличное видео. С меня лайк
@yashrewalia2116
@yashrewalia2116 4 жыл бұрын
Can you give the calculation related to the circuit for DC clamp
@MCsCreations
@MCsCreations 7 жыл бұрын
Really nice! Liked specifically the ugly tooth you put in it (at 14:07), looks an angry animal. LOL
@johnopfer8065
@johnopfer8065 4 жыл бұрын
What is part number of Hall sensor you used?
@maurizioghizzani5734
@maurizioghizzani5734 6 жыл бұрын
If i change the coil size does the sensitivity change? What op can be used to improve the precision ? Thank
@ELECTRONOOBS
@ELECTRONOOBS 6 жыл бұрын
To improve the amplified signal you could use the same OPAM but in a chain connection, the output from the first OPAM to the input of the second but with smaller scales.
@FriendlySuslik
@FriendlySuslik 7 жыл бұрын
no se para que sirve pero lo quiero, y lo quiero ya
@0dium.
@0dium. 4 жыл бұрын
HAL sensors are great components
@genuino-qo5yq
@genuino-qo5yq 7 жыл бұрын
Pls make an arduino based switching power supply
@joycepark6299
@joycepark6299 4 жыл бұрын
Hi LM324 is currently not available in our area so we used LM358 but the result is kinda sketchy. Can you recommend to us other IC to ampli the result? Thank you.
@joycepark6299
@joycepark6299 4 жыл бұрын
and also when we try it we got a result of 0.025-0.033 V (without conductor on the magnet) and 0.099-0.106 Voltage (with conductor). Then on our second test we got different result, does the circuit really had approximately 0.025V ? Thank ypi for answering it will be a great help in our project.
@gastarbieter
@gastarbieter 6 жыл бұрын
what is your opinion about the hantek current clamp?
@ELECTRONOOBS
@ELECTRONOOBS 6 жыл бұрын
It's a decent one. I don't use clamps too much. The good thing is that it is quite low price.
@thelasttimeitried
@thelasttimeitried 5 жыл бұрын
Really great video. Thanks for taking the time to create the project and explain it so thoroughly. By way of improvement, the letter 'u' in the word 'circuit' is not pronounced. Your English is great!
@mihapeterle204
@mihapeterle204 5 жыл бұрын
Why inverying amp and not noninverting?
@Tirdad1981
@Tirdad1981 5 жыл бұрын
I built this but it can only measure DC currents. I can see no changes in hall sensor output voltage with AC.
@gunjankumar-fr8lv
@gunjankumar-fr8lv 4 жыл бұрын
How to remove magnetic field around wire so that the clamp meter can not read the current ?
@peterdkay
@peterdkay 6 жыл бұрын
Great explanation, however I think schematic is wrong. You show a 9M/10pF in series with scope connector. As scopes have a 1M input impedance this filter has a 10:1 attenuation so maximum voltage at scope is 0.9V not 9V. I would like to see frequency response: You measure rise time of clamp by generating a 100mA current pulse at 1kHz. Easy to do using a 100 ohm resistor in emitter of transistor and drive base with 0 to 1.5V square wave. Collector current should be about 0 to 100mA square wave. (The 1.5V drive is to overcome 0.5V base emitter voltage.)
@2008007flavius
@2008007flavius 7 жыл бұрын
Whats up my friends!!!!!
@MrHD71
@MrHD71 7 жыл бұрын
what is the better amplifier that you're waiting on?
@ELECTRONOOBS
@ELECTRONOOBS 7 жыл бұрын
LM358
@SianaGearz
@SianaGearz 6 жыл бұрын
Waaait. LM358 and LM324 are the same thing! Different packaging, different number of units per package, but same units inside. You can even use the extra units of LM324 to increase either noise and distortion suppression or current handling capability.
@sincerelyyours7538
@sincerelyyours7538 6 жыл бұрын
Can you show us how?
@nikgru4577
@nikgru4577 5 жыл бұрын
I have the Same Multimeter
@eb2615
@eb2615 4 жыл бұрын
Be very careful when using current transformers if you leave the secondary open circuit you can generate very high voltages when there is a current pulse or surge always terminate the secondary with a load resistor or are use back to back senders ect
@sonyobright2106
@sonyobright2106 5 жыл бұрын
the 49e hall sensor has a bias voltage of half the power vcc ... means that the hall sensor would output a 2.5 v for a vcc= 5v with NO magnetic field sensed by the sensor ... the potentiometre help to offset that bias voltage ...the inverted configuration help for the gain. in this case 100. witch is too big in my opinion .. a gain of 10 will be more than enough.. another strange thing is the 9v battery that is too big for the sensor. in the end the filter is wrong and not suitable for this ...good work
@apurvakalvade2301
@apurvakalvade2301 5 жыл бұрын
From which instrument did u get that ferrite Core?
@MunnaKumar-sc7qo
@MunnaKumar-sc7qo 5 жыл бұрын
desktop power supply or ATX supply
@apurvakalvade2301
@apurvakalvade2301 5 жыл бұрын
@@MunnaKumar-sc7qo and in case if we don't want to use BNC connector and want the reading on the LCD _ then if we directly connect the output of the OPAMP to the LCD, will we able to get the display of current ratings on LCD?
@MunnaKumar-sc7qo
@MunnaKumar-sc7qo 5 жыл бұрын
@@apurvakalvade2301 yes, but you must change the gain of op-amp as per you lcd working. If you control by any microcontroller then you must use ADC value range.
@EASYELECTRICALENGINEERING
@EASYELECTRICALENGINEERING 9 ай бұрын
What is Kurant
@olhalytvyn8715
@olhalytvyn8715 6 жыл бұрын
yellow iron core from a atx dc power supply is no ferrite.its powder iron.it has much more high freq losses.no good for measuring device
@ELECTRONOOBS
@ELECTRONOOBS 6 жыл бұрын
True!
@sonyobright2106
@sonyobright2106 5 жыл бұрын
if your device is working on very low frequency you will get nothing in the output with the ferrite core. so what yr saying is not true ...it depends for what you are using it for ...
@sonyobright2106
@sonyobright2106 5 жыл бұрын
@@ELECTRONOOBS not true ... it depends on frequency....
@francoisBonin-phils
@francoisBonin-phils 3 жыл бұрын
if it was really ferrite , you could not cut it with a hacksaw , anyway , your video is great...
@fatiherdan9510
@fatiherdan9510 6 жыл бұрын
👍👏👏👏
@two_number_nines
@two_number_nines 6 жыл бұрын
ur clamp is actually better, because the core handles high frequencies much better than this iron sheet core industrial clamp
EEVblog 1413 - Oscilloscope Current Probe TEARDOWN + DEMO
38:46
I wish I could change THIS fast! 🤣
00:33
America's Got Talent
Рет қаралды 87 МЛН
Sigma Girl Past #funny #sigma #viral
00:20
CRAZY GREAPA
Рет қаралды 27 МЛН
OMG🤪 #tiktok #shorts #potapova_blog
00:50
Potapova_blog
Рет қаралды 17 МЛН
Panelized PCBs Assemble - Create Your Own Product | SMD Stencil
14:20
Using a Hall Effect Sensor to Measure Current
21:10
Craig Hollinger
Рет қаралды 35 М.
Understanding Current Probes
11:01
Rohde Schwarz
Рет қаралды 7 М.
how to convert a CRT TV into an oscilloscope
8:14
inventor KR
Рет қаралды 342 М.
FLYBACK DC - DC Converter Theory And Example
12:09
Electronoobs
Рет қаралды 223 М.
DIY Current Probe
6:55
FesZ Electronics
Рет қаралды 15 М.
How to measure Buck converter loop gain and phase
24:17
Richtek Technology 立錡科技
Рет қаралды 47 М.
Make Oscilloscope from Phone
12:45
Awesome Tech
Рет қаралды 277 М.
3 Simple RF Detector Circuits / Radio Signal Field Detector
8:23
ZAFER YILDIZ
Рет қаралды 55 М.
Хотела заскамить на Айфон!😱📱(@gertieinar)
0:21
Взрывная История
Рет қаралды 4,5 МЛН
1$ vs 500$ ВИРТУАЛЬНАЯ РЕАЛЬНОСТЬ !
23:20
GoldenBurst
Рет қаралды 1,4 МЛН
Simple maintenance. #leddisplay #ledscreen #ledwall #ledmodule #ledinstallation
0:19
LED Screen Factory-EagerLED
Рет қаралды 8 МЛН