5V low level trigger 2 channel relay module to switch up to 10A DC30V or AC250V loads

Рет қаралды 23,811

Күн бұрын

5V low level trigger 2 channel relay module to switch up to 10A DC30V or AC250V loads used in this video was bought by me at the following link amzn.to/2NmXxSr
Hilitchi 360pcs M2 M3 M4 Male Female Brass Spacer Standoff Screw Nut Assortment Kit amzn.to/2IFYjpf
Datasheet for almost exact same component is at www.handsontec.com/dataspecs/2...
www.amazon.com/shop/electronz... Electronzap earns money from this storefront and many of the links to products.
/ electronzap
/ electronzap I now do my gaming, Fallout 4 for now, on Twitch.
#relay #module #multimeter

Пікірлер: 40

@russellniebolt1493 5 ай бұрын

Wa-la sir, NOW I understand relays. I could not find anything else that told me what the 3 terminal posts were (per relay), on the far side of the relay. Thanks, well-explained.

@Electronzap 5 ай бұрын

Glad to hear, thanks for watching!

@sofakng163 4 жыл бұрын

Very helpful video. Thanks a lot for posting this!

@Electronzap 4 жыл бұрын

Thanks for watching!

@djrkzr 2 жыл бұрын

Finaly someone was ably to explain this simple topic in not over engineered form👏

@blackturtleshow 5 жыл бұрын

Very interesting information! Excellent presentation!

@Electronzap 5 жыл бұрын

Thanks!

@tomas_bohuslav 3 жыл бұрын

Thank you for the explanation! :D

@Electronzap 3 жыл бұрын

Thanks for watching!

@juancarlossalazarvaca7080 2 жыл бұрын

Thx for your video keep going ✌🏻

@Electronzap 2 жыл бұрын

Thank you!

@jeremyrodriguez9815 4 жыл бұрын

interesting explanation

@Electronzap 4 жыл бұрын

Thanks!

@erikryan9982 2 жыл бұрын

Ok but do you need to set the output voltage for DC circuits? I have the same 5v, 2 channel relay that I am attempting to power from a independent power supply to control a 12v Fan, and a 5v Temperature Sensor with.

@tomatexelon 4 жыл бұрын

Good Video, I would like to know the same info but on the jumper side of it, You never talked about that part.

@raurenyumen3435 Жыл бұрын

Thanks... I have a question, can I use different power supply to trigger the relay? I saw you use negative from same ps to switch the relay, I am thinking to use a different supply to trigger it, is that possible?😊

@Electronzap Жыл бұрын

The relay coil is all that gets powered. The switch part of the relay can switch a completely different power source.

@AztecWarrior69 2 жыл бұрын

Holly crap I didn't know Norm McDonald knew electronics! RIP

@Electronzap 2 жыл бұрын

Yeah, sad that he is gone now :(

@AztecWarrior69 2 жыл бұрын

@@Electronzap yeah you really do sound like him. Bet you hear that often . Oh BTW there are some offset standoffs that are plastic that you might wanna look into. I got some and love using them. I think they are called video game console standoffs. The screws they come with have large heads and can't be used with these small relay boards. Had to go to local screw and dolt place and get a few hundred for 3 bucks. I'll link to video where I used them and find what size screws I got when I get back in town.

@Electronzap 2 жыл бұрын

@@AztecWarrior69 I've been told that I sound like Norm for over 25 years now lol. I was surprised nobody mentioned his passing sooner.

@flickmew99 Жыл бұрын

Question : so to measure current used by switching operation, I should break the 5V to Relay's VCC connection ?

@Electronzap Жыл бұрын

Almost all of the module's power should be for the relay coil. Just a little current is needed for the circuitry. So, I would just measure the whole current of the module when it is switched.

@juliusferrer2071 6 ай бұрын

so that means...if the relay is a low trigger type... when I use the contacts (com no)...the load must be connected to negative supply..right? also, is it possible if the load is supplied with 12v while ground is connected to the ground of arduino?

@Electronzap 6 ай бұрын

The switch part of the relay is just a mechanical switch. A magnetic field is what moves the switch position. None of the electricity from the module makes it to the switch part, so you can wire up a load however you normally wire it up to a mechanical switch.

@juliusferrer2071 6 ай бұрын

@@Electronzap im still confused..still wont work for me..i followed the video only to replace the led with 12v solenoid lock...i expect the output would be like the led but it wont work

@AdrianHiggins83 5 жыл бұрын

Say I had a roller door that has auxiliary output that pulse for one second when button pressed how could you connect that to this relay to switch a light ?

@Electronzap 5 жыл бұрын

Not sure, and this is probably not a bad relay for that. I'd try to find a relay made for that and follow their guidelines.

@Electronzap 5 жыл бұрын

Oops, I meant to say that this is probably a bad relay for that.

@AdrianHiggins83 5 жыл бұрын

electronzapdotcom yes, I have been trying to find something other than a pic that would work , issue is with the signal being pulse on for 1 second. I have tried 2 transistors using caps to toggle but was unreliable.

@Electronzap 5 жыл бұрын

Yeah, sounds like a tricky circuit to design.