People like you are a godsend. I love my new Elite controller and know in some time that the sticks will fail and your work makes it so I can try fixing it myself and provide service others that are less confident and cannot do it themselves. We need more people like you in the world.

I just recently subscribed to you. I like youre professionalism and personality, keep it up!

Great video mate funny that piece flying off 😂😂

Bravo even more helpful than the Microsoft step by step tutorial !!😊

Great video. That flying magnet, though😂

lol the magnet pinging off got me good

Excellent video. And very helpful

just what I was looking for my housing cracked where the grip is overall the controller is working fine so basically just moving stuff into the back housing and not needing to do anything with the middle ordered full housing hopefully be with me next week, Thanks :)

Do you know the function of the two metal sponge-like small cubes underneath the green pcb visible at 18:43? I'm repairing my controller but accidentally melted one of them and have no idea what they're called or how to get a replacement (or if they're even necessary, it seems yours are not super aligned when you put the bottom part back on again). Thanks for making this video, very nice repair!

Amazing job! What were you doing to the potentiometers when reassembling? Can you adjust them to get the more centred?

where you got the blue dpad and the paddle buttons blue like the og halo controller

Hey mate I was wondering what kind of cleaner/fluid you use in the ultra sonic cleaner.

I can’t get the wires to stay, the ones that are under the black tape

Sadly I dont live in the UK and cant send my controller into repair, but is it likely I could replace the shell on my own? I have no beforehand experience, neither the best tools

Excellent repair! What kind if thread locker do you use?

Sheeeesh… 👏👏👏

Do we need to solder the wires off? Or can we work with them on? Because I’m needing to change my shell

i feel like once you worked yout magic on these they will work for ever lol

Same thing happened to mine the handles crack over time

Just did a swap for my elite v2 this week and everything fit well but now I keep having disconnect issues and I have no idea where to go back to. I reopened and doubled checked each step and it didn’t look like I messed up. I’m thinking it might be the two small cables that run from the blue card to green. Any suggestions would be greatly appreciated.

Does it matter which gue to use whjen adhering the magnets to the new shell? I went to change mine and realised I had nothing to stick them back on

I just replaced my rear shell and no matter how much I re seated the trigger stops I couldn't get them working. I don't get how I done it wrong!

How did you get the analogs out so easily? What heat did you use and approx how long did you apply it

I had fix un elite 2 lt button, costumer have break many part plastic. Fortunally i use super glue

Do you loose the tension adjustment when you replace the stick modules on the series two controller?

My elite series 2 controller is connected to my Xbox but does not work altogether. I opened up the controller to fix the bumper not working and since then the controller has stopped responding. It can be turned off through a hard reset but there is no response on my Xbox. Does anyone know how to fix

arigato :D

Have you bought this on Ali?

I change the rear shell when i put back together the trigers stop in the same place no mater where the stoper is and if i press to hard the triger will go all in and get stuck any idea

What’s the screwdriver you used in min 6:57? Is it the same as min 7:05?

What’s the stuff you put on each of the triggers when you assembled it

Great video bro 👍🏼 so I was finally able to fix that elite series 2 controller that wouldn’t take a charge or power on. Followed the same steps you took on your other video where you reflowed the cpu however I was able to get away with just cleaning the cpu with 91% isopropyl and a bristle brush also flushed it with the alcohol and let dry 🙏🏼 got it to charge and power up but upon further inspection both P3 and P4 paddles are non functional so when I took a look inside I seen a pretty obvious fault, the pins or tabs, prongs? Not sure the proper terminology but where the motherboard makes contact to the buttons/ pads of the paddles the pins are all broken/bent is it possible to replace theses? The points on the motherboard are J15 J16 J17 J18 if so I would greatly appreciate the advice, and maybe a video on how that would be done?

What glue do you use for the magnets of the elite series 2?

Lol how much did this cost?

Flying magnet!

We must have both gotten our controllers from a bad batch !! Mine also seemed to self destruct from dry rott !! Ha Ha !!

I have no idea, but I assume your beautiful rebuild is less expensive than a new controller. Nice job.

Hola ¿Qué pegamento utilizas para las partes de metal?

How much does it cost for a full refurb of an elite 1 and 2

what size is the smallest screwdriver used here?🪛