How To Repair Carbon Fiber Cracks

No video

How To Repair Carbon Fiber Cracks

Рет қаралды 361,289

Күн бұрын

In this video I show you guys how to repair carbon fiber cracks with nothing more than sandpaper, resin, polish and elbow grease!
Fixing your broken carbon fiber parts can be time consuming but it is economically worth it since carbon fiber parts are very expensive!
Remember not to sand the exposed carbon fiber cloth if you can avoid it! Disturbing the weave will make your repair obvious. If the cloth has been cracked through, you can still salvage your part if you do not care about how it looks. Reinforce the back side with a new piece of cloth and soak it in resin. Use chopped carbon fiber on the front and build up the area until there is no longer a void. Sand smooth and polish for a nice finish!
For this project, I used System Three epoxy resin get that awesome look. As an Amazon Associate I earn from qualifying purchases (at no extra cost to you):
System Three Epoxy Kit:
amzn.to/3zI7kZk
Disposable Measuring Cups:
amzn.to/3zKdcB7
PowerBall Polishing Tool:
amzn.to/3OKVFx1
Polishing Compound:
amzn.to/3PLmuSV
2x2 Twill Carbon Fiber if you need to reinforce the back side:
amzn.to/3cHmQeL
Alternative Epoxy Resin Kit with Measuring Cups:
amzn.to/3bgntLZ
If you want to make your own carbon fiber parts, I suggest you check out my other video here:
• How to Hand Lay Real C...
Thanks for watching and be sure to subscribe for more!
****************************************************************
If you enjoy and have benefited from my content and are feeling generous I would love your support! You can "buy me a coffee" here:
► www.paypal.com... ☕
By supporting my channel you are encouraging me to continue with this time consuming endeavor. A lot of time goes into design work, building my projects, filming the videos, editing the videos, etc. Plus it all costs money! Your generosity goes a long way in helping me bring you better content as often as I can!
Follow me on Instagram!
► / embracemaking 📷
If you liked this video, perhaps you will also enjoy some channels that I personally find inspiring and interesting...
DIY and MAKER:
► The Hacksmith
/ @hacksmith
► Adam Savage Tested
/ @tested
► Thomas Sanladerer
/ thomassanladerer
Car Content:
► Mighty Car Mods
/ @mightycarmods
► Drivetribe
/ @drivetribe
#carbonfiber #DIY

Пікірлер: 303

@mackchannel6348 2 жыл бұрын

Very good procedural tutorial on how to repair carbon fiber. No need to allow shops to charge huge repair fees as long as you're willing to be resourceful.

@EmbraceMaking 2 жыл бұрын

Glad it was helpful!

@mackchannel6348 2 жыл бұрын

@@EmbraceMaking I haven't used it yet, but I have some carbon fiber parts coming and it's good to know that there are ways to effect repairs without resorting to going hat (and wallet!) in hand to a shop who will doubtless wring their hands and suck their teeth and say "That's a hard one. Let us get back to you." and then it's a $2000 bill.

@larsbee 8 ай бұрын

this is not a crack in the Fibre itself!

@primitxve8076 3 жыл бұрын

3 years later and this video is still useful. I bought a really bad condition CF hood for my g35. I got it for 100$ had some deep cracks on both sides as well as the front. I sanded, filled with resin 3 coats. One one side the cracks are completely gone. On the other side they are still visible BUT it has a layer of resin so you can’t feel it, imma wrap it and leave the vents visible. Thank you very much for the video 🔥

@plusdaddyyt Жыл бұрын

Crazy I’m in same boat .. 350z hood seabon for 100 I’m trying to fix lol

@franciscoencinas4440 Жыл бұрын

haha im in the same with a front lip for my camaro, lip it self new is 500 and i got it for $50

@ethanhenry9484 7 ай бұрын

@@plusdaddyyt same boat lmao CF G35 Seibon hood for $140 thats cracked allllll over the place

@TyFknGuy 3 жыл бұрын

Dude, thank you. I cracked my Seibon hood last week and they don't make them for my car anymore. This was a super informative video, even 2 years later. Subbed'

@EmbraceMaking 3 жыл бұрын

You're welcome! Thanks for the sub. Have you tried to fix it yet?

@TyFknGuy 3 жыл бұрын

@@EmbraceMaking No sir; I always run myself thin and have a few projects going on currently. The car is garaged at the moment. the damage looks similar to your diffuser in the video, so I'm really hoping for decent results when I get the resin in.

@joeKisonue 2 жыл бұрын

I had a seibon wing for my prelude. After 2 years it started yellowing. I restored it but it would haze quickly. Started just spraying silicone and wiping down. It is supposed to be higher quality than that. Wasn't impressed.

@spencernussbaum9337 Жыл бұрын

Excellent procedure for repairing carbon fiber cracks , I used this fix to repair golf club driver head carbon fiber crown bad crack. It works well after repair. I used J-B ClearWeld.

@EmbraceMaking Жыл бұрын

Thank you!

@jaawxyz5325 3 жыл бұрын

This video is a live saver! Thank you for being so thorough with the explanation hopefully I can fix that chip in my trunk !

@EmbraceMaking 3 жыл бұрын

Glad it helped and thanks for watching!

@brantleybonner1696 5 жыл бұрын

My drum pad is cracked and this guy basically fixed it for me. Thx

@Q50WO 2 жыл бұрын

Great stuff. Thank you. I truly appreciate you including alot of the necessary information that people often exclude.

@EmbraceMaking 2 жыл бұрын

Glad it was helpful!

@davidknechtel3416 6 жыл бұрын

Exactly what I needed, Thank you for this!

@EmbraceMaking 6 жыл бұрын

You're welcome, thanks for watching!

@LetsDIYIt 3 жыл бұрын

I just bought a 911 with all carbon fiber interior trim. Almost every piece is cracked. My plan was to replace everything over time, but I could probably buy another Porsche for the cost of that. I think I'll try you methods on the most inconspicuous piece/spot to test my skills and see how it looks and then go from there. Thank you for the video

@EmbraceMaking 3 жыл бұрын

Best of luck, for the cost of the new parts from Porsche I am sure the effort and elbow grease will be more than worth it.

@sluggomagoo 5 жыл бұрын

Nice that you explain all your mishaps.

@EmbraceMaking 5 жыл бұрын

Learn from my mistakes :) Thanks!

@neilbutler-wasabirc8941 4 жыл бұрын

Thanks for a great video. I have a carbon spinner on a RC plane that got scratched in a crash. This is going to help a lot to solve the problem and get the spinner back to looking good.

@EmbraceMaking 4 жыл бұрын

Good luck!

@stevenz931 4 ай бұрын

Bro your a really good teacher, thank you

@EmbraceMaking 4 ай бұрын

Thank you so much!

@casualguy3938 4 жыл бұрын

Mixing the catalyst and the resin too quickly will also make bubbles. Mix it a bit more slowly instead of whipping it up ;)

@EmbraceMaking 4 жыл бұрын

Good tip! A nice smooth pour and mix helps prevent bubbles for sure!

@user-cj2vu4jn7v Жыл бұрын

I have a question I have a carbon fiber hood and it has done spider cracks that have shown up they look like they are in the gel coat not into the fiber. What of the best way to go about fixing them?

@casualguy3938 Жыл бұрын

@@user-cj2vu4jn7v Sand the area but NOT the carbon fiber as he says in the beginning of the video. It is important to take your time and ONLY sand the gel coat. Clean it and then apply a coat of gel coat. After it dries lightly sand the area again and apply another coat of gel coat to fill it in just as he is doing above. The key is to slowly build it up with more than 1 layer.

@user-cj2vu4jn7v Жыл бұрын

@@casualguy3938 The gel coat should I use the epoxy he used in the video?

@casualguy3938 Жыл бұрын

@@user-cj2vu4jn7v I think all of them are very similar as long as you get a decent quality one. If you have experience working with one of them then that is what I would use. I would even go so far as to put a few coats of wax on it a few days after completion.

@neonnerd1364 4 жыл бұрын

Great video. I have a carbon hood on my car thats cracked and you can't find a replacement in the exact same style or any other hood that looks good so this is gonna help me out tremendously.

@EmbraceMaking 4 жыл бұрын

Glad it could help!

@ericturrentine4400 3 жыл бұрын

How did you hood turn out? Have a crack in my hood now

@neonnerd1364 3 жыл бұрын

@@ericturrentine4400 I actually haven't done it yet lol. Getting ready to do it soon though.

@martinterence592 Жыл бұрын

To prevent bubbles use MEK, blow with air and pay attention to your resin that nothing goes in during combination nor dirt on the part where you are using resin. Some dust can create air bubbles and that's why it comes out like that, while polishing with resin also your brush should be new and clean, alway use air blowing and after MEK.

@EmbraceMaking Жыл бұрын

Great tips, thanks!

@acirinelli 3 ай бұрын

My GranTurismo rear diffuser is scuffed up, and I’m going to try this!

@EmbraceMaking 3 ай бұрын

Have fun!

@brosec5840 5 жыл бұрын

Wow, thanks for the tips. I am looking to repair the front spoiler on my XKRS , I will definitely be taking my time on it. Good video 👍

@EmbraceMaking 5 жыл бұрын

Thanks! Best of luck, I hope it works out!

@ashlinmcdermott4563 5 жыл бұрын

Bout to do this to my hood! Thank you.

@EmbraceMaking 5 жыл бұрын

Best of luck!

@MrNicholaslentini 5 жыл бұрын

Samee got mine for 200 originally 1500 worth the repair

@davis7323 3 жыл бұрын

I'm sick of NY.. I just hit someone's leather workboot on the highway and it cracked my front lip on my m4. It damaged the weave a bit. I ordered the resin you have here, going to try to repair it... I'm aware the weave damage will show, I hope I can shape the resin into its original shape with alot of coats and sanding...thank you.

@EmbraceMaking 3 жыл бұрын

I feel you... I almost smoked a spare tire someone left in the middle of the highway the other day. Would have been a big repair bill. Good luck with your fix!

@keithjenkins6523 3 жыл бұрын

A piece of semi truck tire tread got my m4s front bumper this week so I feel you.

@sagew7377 3 жыл бұрын

I backed my carbon fiber diffuser into a pole thank you so much 🤣

@EmbraceMaking 3 жыл бұрын

No problem 👍 Glad it was helpful!

@dido1803 3 жыл бұрын

Hi there, awesome demonstration. I'm planning to fix my carbon bike that has very similar ding.

@EmbraceMaking 3 жыл бұрын

Glad it helped! Hope that works out for you!

@jg_media9 4 жыл бұрын

Thanks for this! Just what I needed to give this a go myself

@EmbraceMaking 3 жыл бұрын

Glad I could help! Hope it turns out for you!

@AlienMonkeyDXB 5 жыл бұрын

Very clear tutorial.Thank you!

@EmbraceMaking 5 жыл бұрын

You're very welcome! Thanks for watching!

@l1ve2f1sh 2 жыл бұрын

Thank you! Great practical approach!

@EmbraceMaking 2 жыл бұрын

You're very welcome!

@RodrigoNascimentoMattos 5 жыл бұрын

bubbles in the resin are a common thing. you need to degass it first using vaccum chamber and pump. i use it a lot. zero bubbles.

@EmbraceMaking 5 жыл бұрын

Thanks! This method is more of a low cost "common tools" way of doing this without much monetary investment :)

@RodrigoNascimentoMattos 5 жыл бұрын

@@EmbraceMaking yeah it requires some investment, and its a next step for those who are tired of this lil bubbles :) I know because it happend to me :)

@emirdag7995 4 ай бұрын

What an awesome video! thank you so much for this. I have a fully cracked carbon fiber front lip all around tbh, should I try to peel and fix it or apply a layer of carbon fiber fabric? I really don't know how to proceed

@sethamoto9061 2 жыл бұрын

amazing video bro. I went down on my Yamaha R1 and I have a lot of carbon fiber fairings that I thought were protected by all my frame sliders. Which they were, except for one little section on the front tank cover. The damage looked very similar to this and I hope this works for me.

@EmbraceMaking 2 жыл бұрын

Glad I could help, let me know how it goes!

@joeKisonue 2 жыл бұрын

How did it come out?

@sethamoto9061 2 жыл бұрын

@@joeKisonue real good. Honestly forgot about it until now lol

@jeffreygomez7360 5 жыл бұрын

Nice vid, I heard if u use a heat gun on the epoxy bfor it cures u can eliminate air bubbles n prevent them from cosmetically damaging the appearance

@EmbraceMaking 5 жыл бұрын

That works too! Just can't over do it with the heat

@joeKisonue 2 жыл бұрын

It's nice to have a gun with a screen readout and good temp control

@jdmchickkustomz9417 4 жыл бұрын

That looks amazing I wish I could fix my hood like that but unfortunately it is cracked and busted all over 😣

@j7... 3 жыл бұрын

Just tape it. Because racecar 👍

@claytonaden1091 3 жыл бұрын

Thank you for this video!!! Now to fix my Carbon Fiber wing!

@EmbraceMaking 3 жыл бұрын

Glad I could help! Thanks for watching!

@edgarcarrillo8503 3 жыл бұрын

How did it work?? Planning to do mine soon

@mustangmach11419 Жыл бұрын

Great video I’m happy you took the time to show the steps thank you

@BrianJKelly3244 4 жыл бұрын

Really enjoyed the video and the way you go about explaining the process and tips/tricks and also warn about gotchas! Thanks!

@EmbraceMaking 4 жыл бұрын

Glad it was helpful!

@Grooove_e 3 жыл бұрын

Got my hood for 50 dollars originally 1500 only one decent ding thanks for this

@EmbraceMaking 3 жыл бұрын

Hope it works out for you!

@CMOVlogs 5 жыл бұрын

awesome video, thanks. got a crack in my CF roof on the M6 =(

@EmbraceMaking 5 жыл бұрын

Time to fix it! ;) thanks for watching!

@covingtonja3 3 жыл бұрын

Does anyone have any long term 1-2 year update on how this fix is holding up? I’m planning to use the same exact resin from the video, but wanted to see if this has proven to be stable and held up for anyone...or not. Using this for a CF roof, so I need it to. Great video and hope it has worked! Thanks!!!

@EmbraceMaking 3 жыл бұрын

So far it has worked out for me... I still have this piece and it looks fine. That being said, full disclaimer my car does not sit out in the sun.

@theanswer69786 5 жыл бұрын

u just saved my car's cf lip:)

@EmbraceMaking 5 жыл бұрын

Awesome! This is why I do what I do :)

@MARCD832 6 жыл бұрын

I been waiting for a vid like this to fix the lip on my Vette! Thanks

@EmbraceMaking 6 жыл бұрын

No problem, thanks for watching Marc!

@Youcantdoxxme 2 жыл бұрын

How long did it take for the resin to harden?

@EmbraceMaking 2 жыл бұрын

I believe I was giving it a full 24 hours before considering it fully cured

@slickrickdarula9483 2 ай бұрын

Can you use 5 jb weld 5 minute epoxy?

@Berge1616 3 жыл бұрын

Super stupid question, but i guess you remove the tape before the resine complety dry?

@joeKisonue 2 жыл бұрын

I would

@Irizar6489 3 жыл бұрын

Tuner Cult! by looking at the shirt we entered the same sweepstakes hahaha

@EmbraceMaking 3 жыл бұрын

I've had these shirts for yearsssss, but yes Tuner cult. I think I bought them wayyyy back in the day when they were $6 each haha!

@bubblerings 2 жыл бұрын

On my Carbon diving fins.. I use a heat gun on Low setting to pop the tiny bubbles.. 😎 And not too close... Just until they pop. Much easier if the part was flipped, so the repair area is more flat, not vertical.

@joeKisonue 2 жыл бұрын

Yeah on large projects people use the propane torch

@edward6850 5 жыл бұрын

Great quality and Very helpful. Thanks!

@EmbraceMaking 4 жыл бұрын

Thanks, much appreciated!

@hopeless__-ut6tg 4 жыл бұрын

What would you do of you had some webbing on the finish? Where the carbon fiber isnt cracked, its till intact, but the clear coat has cracking all over it?

@EmbraceMaking 4 жыл бұрын

You would have to try and sand through the spider webs portion the best you can. Even if you get most of the way through and put new resin over top it would probably hide most of the flaws.

@stuffzoom 27 күн бұрын

What would happen if I just fill the cracked area without sanding?

@EmbraceMaking 25 күн бұрын

Might run the risk of it not properly binding and then eventually it separates

@stuffzoom 25 күн бұрын

@@EmbraceMaking Do you think I could end up worsen the situation? I have a daggerboard with some carbon at the edge - there is a small area (

@codykellner9985 2 жыл бұрын

Great video!!...I got a question..if I cut into my carbon hood will I need to use a resin to reseal the part I cut a hole in for a hood latch?...or can I use something like silicon?

@EmbraceMaking 2 жыл бұрын

I would clean up the cut edges with a bit of epoxy if you can. Sand them smooth without fraying the fibers and dab a bit of epoxy on to make sure they don't fray any further.

@Chapiza700 3 жыл бұрын

Where can I find resin with the carbon fiber in it?

@hunterschaumleffel2143 Жыл бұрын

Did you have to mix new epoxy each time you came back to recoat it?

@EmbraceMaking Жыл бұрын

Yes... I mixed small batches at a time

@aduong23 6 жыл бұрын

What kind of hardener did you use with the System Three Gen. Purpose epoxy? The ones I've found by system three states an amber or light amber color.

@joeKisonue 2 жыл бұрын

If it's a very thin application, it should be OK. There are many options

@unresolved777 2 жыл бұрын

Would this method work for my situation : Using your diffuser as an example, I have a duckbill wing, and similar to where the crack is in your vid, I have my duckbill “splitting” open, but running the length along the edge, maybe about 1-2 inches. Like my best example by “splitting” open is a deep cut in your skin.

@EmbraceMaking 2 жыл бұрын

Probably will work fine. Might be a little trickier working on the edge because the resin will want to run, but if you build it up slowly you can probably do it and it will come out better than having a split in it!

@Gyam1981 5 жыл бұрын

Excellent video. I have a CF splitter on the front of my corvette which seems a bit flimsy. How can I reinforce it on the back side so it becomes more structurally rigid?

@EmbraceMaking 5 жыл бұрын

I would put some carbon fiber cloth on the back side and use the resin to bond it to the existing piece.

@oscar27acosta 5 жыл бұрын

Hey man where did you get the resin? Thanks

@EmbraceMaking 4 жыл бұрын

Check easycomposites website, your local composite store, even a local boat repair shop or some auto body shops might have it.

@just.a.simplejoe 7 ай бұрын

Question: if you have a minor crack inside the carbon fiber but it's not a physical crack you can feel......does it matter to try and fix it as so if your just going to paint match the carbon fiber item (ie I'm going to paint match the hood)? I assume no you don't need to fix something minor I'm referring to as I'm breaking the hood down before it's professionally painted but I gotta ask to make sure, it's an expensive item lol.

@Marcinb2410 2 жыл бұрын

Awesome video 💪🏻 thanks

@EmbraceMaking 2 жыл бұрын

Glad you liked it!

@beachboardfan9544 4 жыл бұрын

Couldnt you do a resin infusion setup to draw the resin into the cracks? Kinda like how ppl repair windshield chips and cracks?

@EmbraceMaking 4 жыл бұрын

To be honest I've never seen an infusion set up on carbon that has already been laid up... I basically just made this tutorial for the average person who doesn't have all of the extra equipment... kind of a bare bones approach. Maybe someone has done an infusion repair? I feel like because the resin has already set in the fibers it would be difficult to draw it through the area to repair...

@BigJuicyBlake 5 жыл бұрын

Thank you for this video but I do have a question. After my CF hood cracked, it seemed to have some areas that are really really hazy. I would imagine it’s from moisture getting under the resin. How can I get rid of the haziness?

@EmbraceMaking 5 жыл бұрын

Haziness could be from UV damage... You may want to try and just use some really high grit sandpaper or emery cloth to remove this hazy layer and then go through the polishing process to restore the gloss.

@ssimpalad 4 жыл бұрын

I am about to do this to my ATS-V front lower splitter. can you tell me everything I need.

@recklesslyarrogant7242 2 жыл бұрын

Thank you for the great video

@EmbraceMaking 2 жыл бұрын

Glad you enjoyed it

@DawidMaksymow 5 жыл бұрын

exactly what i was looking for :) thx you saved me a lot of diggin

@peterhagan2712 5 жыл бұрын

Me too!!

@EmbraceMaking 4 жыл бұрын

No problem, glad it helped!

@kaylaramsburg5402 2 жыл бұрын

So i did resin craft and have a ton of left over craft resin. Its called amazing clear cast. Says its for clear coat and casting resin. Could i use this?

@kevingonzalez348 Жыл бұрын

Does this work for hood with heat I know some epoxy change or get burn

@elachichai 3 жыл бұрын

Do we work the same way for coloured carbon fiber bike frame?

@EmbraceMaking 3 жыл бұрын

Bike frame is structural... not sure to be honest with you, you'd probably have to reinforce with new cloth. You might want to google how to repair structural carbon fiber.

@kylet3589 2 жыл бұрын

What about a trim piece that has a stress crack? Looks like just the resin layer cracked in a long thin crack

@joeKisonue 2 жыл бұрын

Clean and try to get resin deep into crack. Follow the steps to smooth and should be good

@3qdx Жыл бұрын

Not sure you can help me but since you've obviously worked with carbon, I thought I'd bounce it off you. I have carbon fiber forks on my Cervelo Tri-bike, although the appearance is much more just a straight black shiny surface , rather than the carbon as visible as it is in your video here. There is a gouge in the fork of maybe 1/8 inch deep by about 1/2 inch long. I would like to fill it and then buff it back to somewhat of a shine. Rather than the clear resin you used here, is there another black epoxy that you could recommend? I could send you a pic if that would give you a better idea. Thank you.

@EmbraceMaking Жыл бұрын

You can always just add dye to epoxy to color it but for your bike forks you might want to make sure the damage isn't structural? 1/8" deep sounds like its way into the carbon...

@elachichai 3 жыл бұрын

Can you use carbon fiber cloth for glossy yellow finish??

@ernanruiz9631 4 жыл бұрын

i know this is a newer comment but i was wondering where i would be able to buy the carbon fiber cloth

@EmbraceMaking 4 жыл бұрын

Lots of online stores, otherwise if you have a boat repair shop locally, they might have something you can buy. They work with composites all of the time!

@ernanruiz9631 4 жыл бұрын

Embrace Racing thank you very much !

@goldap0987 4 жыл бұрын

thanks bro exactly this video,, for tomorrow 👌👌👌👌 💪

@EmbraceMaking 4 жыл бұрын

You're welcome!

@mohdmahathirnoordin248 3 жыл бұрын

Hi sir..I really need your help..in minutes 6:42 how actually it happen? Its the something on the brush? I really don’t understand how it work..please help me.

@MA69Supra 4 жыл бұрын

Does anyone know if this will work on a cf muffler? I’m trying to do the one on my bike

@chrisdeli7547 4 жыл бұрын

there are resin that they are heat resistant not wih standard resin but it is fixable

@MA69Supra 4 жыл бұрын

Sick I’ll look into that, thank you!

@BianchiEL 2 жыл бұрын

Great video buddy

@EmbraceMaking 2 жыл бұрын

Thanks 👍

@Zamago12 6 жыл бұрын

Hey i have a pretty deep crack on my hood all the way to the fiber and i can literally pull off the cracked parts so If i pull off the cracked parts ill have a spot where the fiber is exposed so do i fill that up with resin and then block sand it so it can be smooth?

@EmbraceMaking 6 жыл бұрын

I would try that, but feather the edges around it so the resin has something to stick to!

@monkiitemps8098 2 жыл бұрын

Thanks for sharing your videos, very helpful. Are you able to share the link to the exact same epoxy resin for us to buy?

@joeKisonue 2 жыл бұрын

It's System III Epoxy resin. Gonna have to Google it up.

@badjuju6563 4 жыл бұрын

Flame lick the resin to remove bubbles, but dont scorch it.

@EmbraceMaking 3 жыл бұрын

I've also done this trick in the past, works nice!

@LuisManuelHdez 4 жыл бұрын

Thanks for the video. I have an expensive mtb with a similar ding and I'm gonna sell it. Definitely will take the time to do this. Could only increase its value. Where could I find that resin mix?

@EmbraceMaking 4 жыл бұрын

thanks for watching! Try your local composites story, or easy composites online, check to see if you have a local boat repair shop or even some high end autobody shops. Epoxy resin!

@joeKisonue 2 жыл бұрын

@@EmbraceMaking I think even Envirotex is the same and available at craft stores like Michael's

@clbaker24 6 жыл бұрын

Embrace Racing Great Video! New Subscriber here! I have a couple of questions...Do you need to clear coat over the resin epoxy after wet sanding? If the Carbon fiber part is clear-coated does the epoxy just blend with clearcoat?

@EmbraceMaking 6 жыл бұрын

When you sand it down you will sand down some of the clear coat if it has been cleared. The epoxy should bond to it. Once you smooth everything out and wet sand the area, I would recommend using a clear coat if the rest of the part has it. Might as well protect it!

@clbaker24 6 жыл бұрын

thank you for the reply!

@lahlah4222 5 жыл бұрын

@@EmbraceMaking kzfaq.info/get/bejne/jsmndtCKlq_DYqM.html

@joeKisonue 2 жыл бұрын

@@clbaker24 I would recommend using outboard motor clear coat. Evenrude or something from a boat place. It's the highest quality rattle can clearcoat available.

@TheSpooofs 5 жыл бұрын

This is very helpful. Thanks for sharing. Also, will the gorilla epoxy resin works on these parts? Thanks

@EmbraceMaking 4 жыл бұрын

I've never seen gorilla epoxy resin before... is that resin or glue?

@jvictormp 5 жыл бұрын

Will this get yellowed if I put on my car roof?

@EmbraceMaking 4 жыл бұрын

Make sure the resin you are using has UV resistant properties, or if you clear coat it after, the clear coat should have UV protection.

@leeexicon 4 жыл бұрын

Have you looked into Gorilla Epoxy Adhesive or J-B Weld Clear Epoxy Adhesive? You think any of those would be good enough? I'm just trying to find something locally and it looks like it's the best I got...

@xkzlx 4 жыл бұрын

I'm in process of repairing my carbon fiber lip for my car (a lot of the original epoxy and coat got removed after the lip fell off on the freeway). I can't comment on longevity since I'm still in process of repairing my lip, but i will say that the Gorilla Epoxy is really easy to use and apply. It's also really easy to smooth out excess layers and lumps using 120 grit sandpaper. After applying the Gorilla Epoxy and smoothing everything out, my plan is to primer, paint and clear the lip. Hopefully these extra layers will protect the Gorilla epoxy from the elements.

@iWillyD 5 жыл бұрын

I have a front carbon splitter that got hairline cracks in it, do you think I would need to reapply resin or could I get away with just sanding down the cracks and applying a clear coat?

@EmbraceMaking 5 жыл бұрын

I guess you could try sanding first... see how deep you have to go. If it is deep enough that you would notice a low spot then use resin. If it is extremely superficial you might get away with just some clear coat...

@OOcean0228 3 жыл бұрын

Can you give me a list of all the tools needed? I am kind of new to this thanks!

@joeKisonue 2 жыл бұрын

A good light, a fine sandpaper assortment from home depot, blue tape, razor, alcohol or acetone, a 2 part UV clear epoxy. Mixing cups, gloves, hair dryer, clean cloths or blue towel.

@drj7328 2 жыл бұрын

I think using a heat gun on the resin could eliminate the small air bubbles when it is still drying👍🙏

@EmbraceMaking 2 жыл бұрын

Just don't add too much heat or get too close with the heat gun

@jimmyc451 5 жыл бұрын

great job

@EmbraceMaking 5 жыл бұрын

Thank you!

@Willhgf 2 жыл бұрын

How much does it cost for all the equipment needed to do this job?

@EmbraceMaking 2 жыл бұрын

I don't remember it being much... not sure what a small container of resin is going for these days but the rest is basically just abrasives and polish which is cheap

@jasonglow9799 4 жыл бұрын

Great video.

@EmbraceMaking 4 жыл бұрын

Thanks for watching!

@joeya5779 4 жыл бұрын

Mines stayed hazy after wet sand and polish what do i do to fix this? Used same stuff as you.

@EmbraceMaking 4 жыл бұрын

What kind of polish did you use and what kind of cloth? Maybe you are using something too coarse still?

@caraddix 3 жыл бұрын

You say: Maybe next time, don't get any air bubbles... You can avoid a lot of bubbles by: Letting the resin sit a little bit after you prepared it/use a mini torch (like a lighter size) to go over the surface of the resin. Also, there's bubble crack spray on the market but personally I'm not a big fan of that stuff...

@EmbraceMaking 3 жыл бұрын

I've used the heat gun and acetone spray trick before when I did some carbon fiber wrapping. Works decent but acetone spray is pretty bad for you. Something to keep in mind.

@caraddix 3 жыл бұрын

@@EmbraceMaking Bubble burst spray I have is made with Alcohol.

@scubagto420 6 жыл бұрын

Hey question someone dropped a wrench on edge of my hood it took some epoxy off about a quarter size chip that exposed the fabric and around it cracked some epoxy should I chip the cracked parts off or just leave them before I attempt to try this ?

@EmbraceMaking 6 жыл бұрын

Chip off anything that doesn't look like it has a solid bond. Otherwise it may delaminate in the future

@jdmchickkustomz9417 4 жыл бұрын

Where can I find that reson at? do you have a link?

@EmbraceMaking 4 жыл бұрын

Look up easy composites online, they have a nice selection of resin products for carbon fiber!

@MB3DPRINTSGB 3 жыл бұрын

did you remove the masking tape after you applied the exoxy straight away?

@joeKisonue 2 жыл бұрын

You should

@JesusGodHolySpirit3 4 жыл бұрын

What if it's a HUGE crack? For a frame of a fork? Will this work for that?

@EmbraceMaking 4 жыл бұрын

I wouldn't use this method to perform a structural repair. This is mainly for looks

@JackRR15 4 жыл бұрын

What if you are re-doing the whole resin on a front lip for example? Do you still do it in batches?

@EmbraceMaking 4 жыл бұрын

If you mix too much at once, keep in mind that the heat from the reaction can get intense! It will cure very quickly before you can work with it and in some cases get so hot it can actually start smoking and catch fire! Many years ago I had it melt right through a container! Read the labels!

@JackRR15 4 жыл бұрын

@@EmbraceMaking Thanks I actually really didn't need a lot even for the whole lip.

@Jaaybirrd4419 6 жыл бұрын

What if you have a crack down to fiber and can’t access back side. Can you repair from the front?

@EmbraceMaking 6 жыл бұрын

Hi Jay, yes you can still patch it from the front side but it will obviously be noticeable. Your best bet is to try and remove this piece to gain access to the back somehow.

@rebarebok3428 5 жыл бұрын

Does this apply to carbon bike frames?

@EmbraceMaking 4 жыл бұрын

You could fix cosmetic damage... but I would trust structural damage to a professional.

@isaiahshearin 4 жыл бұрын

why isn't there links to buy this stuff

@brosec5840 4 жыл бұрын

Hello, does anyone do this type of work in the NYC area?

@EmbraceMaking 4 жыл бұрын

Look for boat repair shops!

@jonienglish3231 6 жыл бұрын

Question is this Epoxy Resin Specific for Carbon Fiber or can i use the RESIN EPOXY that they use For Table Counter Tops ? Looks the Same to me . reason is slightly Cheaper and not alot of place to Mend , my Mountain Bike Cranks have chipped Clear Coat with Exposed Carbon

@EmbraceMaking 6 жыл бұрын

Good question! Not something I've ever looked into. If the countertop resin is epoxy and not polyester then it might work if it's all you can find? It may not have UV protectant in it. There are probably various additives in resins for specific purposes... but if you're willing to be a guinea pig, give it a try and report back!