No video

Emco Compact 8 compound slide enhancements

  Рет қаралды 10,865

Harald Finster

Harald Finster

Күн бұрын

Пікірлер: 18
@dieterlaes9838
@dieterlaes9838 5 ай бұрын
Magnificent work again Harald, thank you for sharing! Love to see your magnificent Thiel 158 in action.
@mftmachining
@mftmachining 5 ай бұрын
Gute Arbeit Harald. Der 02er DCMT in deiner Bohrstange hatte wohl eine unheimliche Begegnung der 3ten Art.....that guy took quite a beating......lol
@HaraldFinster
@HaraldFinster 5 ай бұрын
Ja, der hat einen abbekommen. Für die Emco nutze ich oft PU-Rundriemen, weil ich den überteuerten Keilriemen schonen möchte. Der Rundriemen liefert allerdings nicht das volle Drehmoment. Wenn der Stahl dann einhakt, passiert es mir manchmal, daß ich den Stahl zurückziehe und die Schneidkante ausbricht. Genau das ist hier passiert.
@bobvines00
@bobvines00 5 ай бұрын
Harald, while watching this excellent video, when you got to the part where you were estimating the clearance you needed for your spanner to fit the screw heads, I recalled that my machinist's handbooks all have wrench (spanner) clearances, etc., in tables. If you need to determine spanner clearances again, try looking that information up in your machinist's handbook.
@ABKGRG
@ABKGRG 5 ай бұрын
Well done!
@pirminkogleck4056
@pirminkogleck4056 5 ай бұрын
nice job , i saw it in the Bude ! i tossed my Topslide and mounted a CG25 Soliud toolpost and since then i never ever run into rigidity issues. i went that road because i never need my topslide.
@HaraldFinster
@HaraldFinster 5 ай бұрын
Yes, you are 100% right: I use a solid toolpost whenever possible. If you look closely you will notice that I used it throughout the video. I will need the compound slide for an upcoming project. Thus I found this little project worth the effort.
@pirminkogleck4056
@pirminkogleck4056 5 ай бұрын
@@HaraldFinster i will keep your implemantation in mind in Case i have a good excuse to do that. Allthough,i am currently making a 1895 OTTO Deutz D2 ,and i need the topslide i think i get away with the Original. Topslide since the Jobs are Brass only.
@bambukouk
@bambukouk 5 ай бұрын
Hi Harald, interesting... I have Praezimat (DDR copy of Emco before Chinese did it as well 🤪) Same problem (although it has 4 clamping bolts unlike Emco) My experience is that if clamping plate is too stiff it distorts cross-slide table
@HaraldFinster
@HaraldFinster 5 ай бұрын
Good point about the cross-slide table distortion. I didn't notice any change in the behavior of the cross-slide, but will keep an eye on this.
@johnsherborne3245
@johnsherborne3245 5 ай бұрын
I’m envious of your well endowed scrap bin. Secondly, is there a clever trick to getting absolutely flush countersunk screws? I appreciate what you did her is normal enough, I have noticed in a few instances on my machines that the fit is extremely accurate and I’d love to know how it was done.
@HaraldFinster
@HaraldFinster 5 ай бұрын
Honestly, no, I am not aware of a clever trick. You can certainly look up the correct depth in a machinist's handbook and go from there. And, yes, I went deeper than strictly necessary.
@johnsherborne3245
@johnsherborne3245 5 ай бұрын
@@HaraldFinster my best guess is to use thicker head screws, head proud then machine after fitting. Seems a little of bother.
@HaraldFinster
@HaraldFinster 5 ай бұрын
@@johnsherborne3245 good approach if the head has to be perfectly flush - and you get rid of any markings
@stephanuhu963
@stephanuhu963 5 ай бұрын
Using a countersink that is closer to the diameter of your c/s screw head, and going slightly below the surface, makes for a very neat, flush c/s screw seat. The hole ends up to be countersunk, with a last bit of the hole being straight down just as deep as the rounded top edge of the c/s screw head. Hard to describe!
@Andrew_Fernie
@Andrew_Fernie 5 ай бұрын
@@stephanuhu963Yes, this saves you from needing an overly large countersink in the part to acommodate the non-tapered portion at the head of the screw.
@M.M-M
@M.M-M 2 ай бұрын
Schönes Video und gute Arbeit. Aber warum nicht in Deutsch? Liesse sich deutlich angenehmer zuhören.
@HaraldFinster
@HaraldFinster 2 ай бұрын
Danke! Die Videos sind auf Englisch (mit deutschen Untertiteln auf Wunsch), weil ich damit deutlich mehr Leute erreiche. Neuerdings sind die Videos sowohl in deutscher als auch englischer Sprache verfügbar.
Making Power Feed for Metal Lathe Compound Slide Baileigh PL-1340E
10:02
magnetic base fine adjustment
28:58
Harald Finster
Рет қаралды 3,8 М.
Look at two different videos 😁 @karina-kola
00:11
Andrey Grechka
Рет қаралды 14 МЛН
黑天使遇到什么了?#short #angel #clown
00:34
Super Beauty team
Рет қаралды 43 МЛН
CHOCKY MILK.. 🤣 #shorts
00:20
Savage Vlogs
Рет қаралды 29 МЛН
Running With Bigger And Bigger Feastables
00:17
MrBeast
Рет қаралды 129 МЛН
machining a spindle adapter for a tool grinder
1:04:12
Harald Finster
Рет қаралды 4 М.
how to make long Screw thread by lathe #lathe
6:39
Mr.Experience.
Рет қаралды 9 М.
Solving the CHATTER problem for the home workshop
16:50
Luker
Рет қаралды 150 М.
FAHRION CentroP System in Detail
5:37
Horn USA, Inc.
Рет қаралды 46 М.
Making Worm Gears. Harder Than You Might Think
25:17
Artisan Makes
Рет қаралды 190 М.
Look at two different videos 😁 @karina-kola
00:11
Andrey Grechka
Рет қаралды 14 МЛН