[EN] Watch and Work - Chevrolet Captiva 2.0l 110kW

Рет қаралды 134,652

4 жыл бұрын

Whether you are replacing a timing belt or timing chain, the “Watch and Work” video series provides practical tips on how to replace drive components correctly. Videos are easy to understand, can be replayed at any time and are always geared to the requirements of technicians in auto repair shops.
Topic of the video: Chevrolet Captiva 2.0l 110kW
Products: CT 1121 K1

Пікірлер: 25

@Runyamouth 4 жыл бұрын

Thank you so much. I needed to see this video. So helpfull

@gmustafabaloch6989 11 ай бұрын

Thanks very much for this helpful video

@tevitataai6326 3 жыл бұрын

very well explain sir thank you for your vedeo

@antoinedinh8280 3 жыл бұрын

thank you it helped me

@kyleramonewilliams1860 2 жыл бұрын

Love this engine

@vimilapalaniyandi4547 Жыл бұрын

Thanks for the video

@ContinentalAftermarket Жыл бұрын

You’re welcome

@Cristip 4 жыл бұрын

Great job.

@webberalex9533 5 ай бұрын

Epica 2007 2.0 diesel is it the same engine like on the captiva?

@gabiraboasab2540 3 жыл бұрын

مرحبا انا عندي شفرليت ابيكا فيها. ضوء شك انجن في التابلون فحصت طلع العطل حساس الكمشفط غيرت الحساس والفيشه ولم يطفئ ارجو المساعده

@MohamedKamal-xr2xk 3 жыл бұрын

Thank you for the helpful video. What is the size of the screw you removed to insert the crankshaft locking tool?

@ContinentalAftermarket 3 жыл бұрын

Hey Mohamed, thank you for your comment! The tool EN48246 has a diameter of 11mm how big the screw that must be unscrewed I can not say unfortunately. Best Regards Stefan

@MohamedKamal-xr2xk 3 жыл бұрын

@@ContinentalAftermarket I ordered the kit and replaced it on my own. For the convenience of anyone who wish to do the repair, the screw for locking crankshaft is Torx T50 and for the V-belt tensioner is T60.

@edselytriagolusinchi1620 3 ай бұрын

Hola me puede ayudar con una duda, me gustaría saber si el motor que tiene en el video dobla valvulas le agradecería mucho su respuesta 👋

@ovidiumonoranu367 Жыл бұрын

Thank you for this very helpful video lesson. One question please. Don't we have to change the water pump every time we change the timing belt?

@ContinentalAftermarket Жыл бұрын

Hi, thank you for your comment! We will give you an answer as soon as possible. Best wishes, your Continental Aftermarket team

@robertjohn2249 3 жыл бұрын

When turning the engine twice to check tension after the new belt is installed does the vaccum tool need to be removed and replaced with the vaccum pump?

@ContinentalAftermarket 3 жыл бұрын

Hello Robert, thank you for your question. Yes, the tool must be removed, otherwise the motor cannot be turned through. The pump can be reassembled after the spinning. However, it should be checked whether the tool will fit afterwards, so that the correct installation position for the pump is ensured. Best regards, your ContiTech Team

@robertjohn2249 3 жыл бұрын

Thank you for your email. I bought the locking tools to do the job myself. I see that one locks the camshaft in place. Thank you for your video, it will help me a lot when I have to change both belts, water pump and all my tensioner pulleys. There is another video in German I think with a mechanic showing the procedure with the engine in the actual car, bit more tricky than on a stand haha, but your video was very helpful to me and you saved me $500 Thank you very much

@lukavukas8005 2 жыл бұрын

Wich locking tool do i need?

@kevinpicur7739 Жыл бұрын

I have a 2007 2.0l diesel Captiva and it has a hard intermittent starting problem...nobody knows whats wrong(but when finally starts,it goes well all day)But the next day again it has a hard start