Enclosure build for the XTool D1

No video

Enclosure build for the XTool D1

Рет қаралды 18,914

2 жыл бұрын

I decided to build another enclosure similar to my previous one but with some improvements. I use easy to get materials and make the build as simple as possible. Only basic tools required.
The main body is made of only 5 pieces. The base is 26x26 inches as is completely square.
The 2 side pieces are 26 inches long and 24 inches tall with an angle that starts 12 inches from the back. The back is 27 3/8 wide (using 3/4 material adds the overlap) and 24 inches tall. The front piece is 7 inches tall and 27 3/8 inches wide. The angled front starts at 12 inches from the back and runs to 7 inches from the bottom.
For templates that I have made, check out my Etsy shop. I build files for projects and tools for laser engravers.
www.etsy.com/s...
The links below are affiliate links that will direct you to the product in this video. If you use this link for a purchase, I will receive a commission from the purchase. I remain unbiased and honest in my assessment as always.
XTool: www.xtool.com/...
Comgrow: comgrow.com?sca_ref=2392321.3THJ0z0mmv
D1 10 watt bundle that I have on Amazon: amzn.to/3sJRPMC
Kregg pocket hole bit
amzn.to/3SImUvv
Dewalt 20 volt cordless saw
amzn.to/3SO68Lp
Kregg plywood pocket screws
amzn.to/3zXNbgA

Пікірлер: 96

@brucedutrow1165 Жыл бұрын

Made my enclosure using your idea. It turned out great. Thank You!

@TheClackShack Жыл бұрын

Cool, the design works well for me. Glad you like it. Thanks

@DRK67 2 жыл бұрын

By far the best enclosure I’ve seen!!! You have some serious skills sir!!! Skill and tools I wish I had lol. Thanks for all the awesome content brother!!!

@TheClackShack 2 жыл бұрын

It has taken me a lot of time and money to get my tools to where they are. I am still working on the skills part. Thanks

@ruizd14 Жыл бұрын

Thank you very much for being so detailed and explaining how you do it and what sort of plywood to get. Great timing as I am getting ready to build an enclosure for my Sculpfun S30 10 watt laser and was looking for videos about enclosure ideas and came across your channel (subscribed). Can't wait to watch part 2. Thanks man.

@TheClackShack Жыл бұрын

Part 2 is on the channel. I have built a portable enclosure also. Thanks for watching

@DRK67 2 жыл бұрын

Clacktical enclosure 2.0. You should sell these as kits!! I’d buy one for sure when I get my machine!!

@TheClackShack 2 жыл бұрын

Lol, I got plenty of work already. It is pretty heavy, the shipping would be crazy.

@iron03man Жыл бұрын

Thanks for the enclosure plans !!!

@TheClackShack Жыл бұрын

Any time! Thanks...

@iron03man Жыл бұрын

Just ordered the extension kit for the XTool D1 Pro. Do you have the plans for that size enclosure ?

@TheClackShack Жыл бұрын

Look at my enclosurezilla video. It is the largest one I have.

@pelleparrafin 2 жыл бұрын

Love your vids. I have no Laser yet, but eagerly waiting for my Xtool D1 Pro 20W (inspired by Your excellent videos with the Xtool D1)

@TheClackShack 2 жыл бұрын

I like mine so far. Both of them… lol

@AlienLeader4 2 жыл бұрын

Awesome build video. Would like to see what you do with the ammo cans. Cool idea. Keep up the great work for us all to learn.

@TheClackShack 2 жыл бұрын

It’s coming. I am working on the correct approach.

@BBoyBFit 5 ай бұрын

Be Clacktical! Should be your next shirt design. lol😆

@TheClackShack 5 ай бұрын

Maybe it will..

@danschultz5119 Жыл бұрын

Where did you get the glass for the door, I don’t see a link anywhere?

@TheClackShack Жыл бұрын

JTech photonics or Amazon. Amazon isn't certified laser safe

@danschultz5119 Жыл бұрын

Thank you

@bubbabubba567 Жыл бұрын

❤

@TheClackShack Жыл бұрын

Thanks

@WhisperGentleman 6 ай бұрын

You are like bob ross, except your canvas is woodworking 😂

@TheClackShack 6 ай бұрын

😅

@mikeledee8786 Жыл бұрын

Do you have a video on building a enclosure for the long xtool d1? I bought the long rails for my d1? Thanks

@TheClackShack Жыл бұрын

No but one similar to enclosurezilla is what you would want. I have a video and plans for that one.

@mikeledee8786 Жыл бұрын

@@TheClackShack thanks, I'll check it out

@stevedonalson5675 2 жыл бұрын

Disco laser engraving!

@TheClackShack 2 жыл бұрын

Bringing it back…

@stevedonalson5675 2 жыл бұрын

@@TheClackShack 🕺🏻

@jktrenching9181 Жыл бұрын

Why wouldn't you cut the left and right sides clamped together so you have identical cuts?

@TheClackShack Жыл бұрын

I only had one sheet of plywood, main reason.. lol

@jktrenching9181 Жыл бұрын

@@TheClackShack Than makes sense. Wasn't trying to be a jerk by mentioning it. Just making the suggestion.

@TheClackShack Жыл бұрын

@@jktrenching9181 , no offense taken. That would be a good idea, I just didn’t… lol

@robynblackburn239 10 ай бұрын

Have you ever adapted to include a scissor lift or removable shelf for easy adaptation between rotary and engrave/cut heights?

@TheClackShack 10 ай бұрын

Sure have.. kzfaq.info/get/bejne/o7RkpLyLmc7PoXk.html

@bryanvan1929 Жыл бұрын

Hi, I'm wondering if you know a good place to get the laser safety shield, I'm getting ready to build an enclosure for my d1

@TheClackShack Жыл бұрын

I order mine from jtech photonics. I have ordered from them 3 times.

@bryanvan1929 Жыл бұрын

@@TheClackShack thank you

@dr.richardhigginbotham4073 11 ай бұрын

Great enclosure. I got your plans downloaded. Just wanted to know what program you used to create the plans.

@TheClackShack 11 ай бұрын

I designed the enclosurezilla one in Fusion 360. The other was done by a follower

@DRK67 2 жыл бұрын

Do you have plans to purchase the extended rails and build an enclosure for that!

@TheClackShack 2 жыл бұрын

I am actually waiting for the other axis to get extensions. I figure they will be releasing a 4x4 foot setup soon. They have stretched the hardest part already.

@dillonohrt1903 Жыл бұрын

Great video, quick questions: 1: since you’re burning through a sheet of 4’x8’ anyways, why not give your wires on the right an extra 1” of room? I’m having to plug/unplug those all the time so that would take the strain off those bends on the cable 2: I noticed you’re running 3 leg risers on the tool (very smart) your tool just barely comes up over the front edge of the cabinet. Was there a criteria in deciding how high to have the front come up? Because of my OCD, I would have set it at the same height as the top rail of my tool, maybe even set a decorative lip on the inside to span between the tool and lip. Thoughts on that?

@TheClackShack Жыл бұрын

Basically, that was just the sizes that I wanted it. A year later and it still works as intended. It now houses an Ortur LM3.

@eddiemaness7737 8 ай бұрын

I appreciate your videos. Can you tell me which smoke detector you are using in your enclosures and where I can purchase one? Thanks!

@TheClackShack 8 ай бұрын

You gotta have really good smoke handling or keep it outside. Kidde, pretty much any hardware store or Amazon.

@eddiemaness7737 8 ай бұрын

@TheClackShack Thanks! I didn't know if it was a special type or not. I have a good smoke removal system. I'm planning on adding a smoke detector. Just so happens that my daughter-in-law works at Kidde in Graham, NC. I'll get with her on this. Thanks again and Merry Christmas to you and your family!

@txpete296 Жыл бұрын

Any videos on engraving ammo cans? What is the tape for?

@TheClackShack Жыл бұрын

I have done one but it has been a while.

@jimc31 Жыл бұрын

You think this would be sturdy if it was made out of 1/2”?

@TheClackShack Жыл бұрын

I would imagine. I would predrill holes though to avoid splitting.

@EtchinAaronslaserworkshop 5 ай бұрын

If I have my exhust vent at the top of my enclosure where on the enclosure should I drill holes for better airflow?an how many holes annhow big of holes should I drill to help improve airflow through enclosure an to go outside?

@TheClackShack 5 ай бұрын

I keep answering.... enough to maintain negative pressure inside but not enough to allow it to equalize.

@EtchinAaronslaserworkshop 5 ай бұрын

Sorry if I'm being a pest just wanna get this right

@marvinmurray9630 Жыл бұрын

I love you cabinet, Thanks for the videos, I am starting to build one for my D1 Pro 10w this morning. Off topic just a little, I am a DeWalt man myself, as we have a Stanly Black & Decker plant in out town and can get most of the stuff a little cheaper than retail. How do you like the DeWalt String Trimmer? I have most of the other items you have on the wall but not the Trimmer. Thanks for any advice and keep up the good job with the videos!!

@TheClackShack Жыл бұрын

I will never by a gas trimmer again. It does well for ordinary lawn work. It’s ok with smaller brush and has 2 speed settings. It isn’t a bush hog

@jktrenching9181 Жыл бұрын

since you have a wood shop as well as lasers, would a dust collection system work as an exhaust? I have a heated 16x20 shop framed within a 40x60 shed. The dust collector is in the unheated shed with duct work (pvc) routed into the shop. Would I be able to just connect the exhaust to that system?

@TheClackShack Жыл бұрын

I have considered the same. Only concern would be a spark making it out into the dust filled tubing. If I were to try it, I would make sure to have some way of keeping sparks from entering the tubing.

@timwaderocks Жыл бұрын

Can you add a lightburn camera to the enclosure for more accurate aligning with engraving?

@TheClackShack Жыл бұрын

I have cameras in all my enclosures. Videos also showing setup

@johnathanraney9959 Жыл бұрын

Do you have a link for the laser safety glass you used for your enclosures? Great design! Thanks

@TheClackShack Жыл бұрын

I get it from JTech photonics, I think there is a link in the portable clack shack video

@meliawhite Жыл бұрын

I want to build this for my xTool, but I don’t want the 7” piece on the front. I want to be able to slide the machine/honeycomb/materials in and out easily. Do you think the angle of the lid would be too steep then?

@TheClackShack Жыл бұрын

The cover would be much heavier but it could work with added springs

@torowazup1 Жыл бұрын

👍🏼👍🏼👍🏼👍🏼👍🏼👌🏼🍎😎

@TheClackShack Жыл бұрын

Thanks

@swampratkayak8048 2 жыл бұрын

Great video! I enjoy watching all of your videos. Keep up the great work. Now for the questions. Are you still using or planning on using the air ventilation bottom table on the new enclosure? I like the design. Hypothetically, if I was to use your design. Could I just make the door straight from top to bottom at that angle without making the box design on the front? Would it hit the bottom of the Xtool?

@TheClackShack 2 жыл бұрын

The reason that I keep the box shape is so that I can add leg extensions or etc. and elevate the machine. You could do a slant front but it would limit how high you could lift the machine. I am planning on using a bit of a hybrid to the airflow of my old design. I am going to build a duct inside the enclosure and will have holes along the bottom in a similar design.

@Mark-oj7yt 2 жыл бұрын

Do you think this same style build would work for the extension rail add on to the D1? Basically using the same design just modifying the length to fit the extension rails ?

@TheClackShack 2 жыл бұрын

I would think so, it would need to be built wide side opening to be able to reach everything better. The added weight to the lid might require some struts near the center to help open it.

@Mark-oj7yt 2 жыл бұрын

@@TheClackShack Do you have future plans on adding extension rails to make your D1 bigger? Or do you find yourself not needing the larger base ?

@TheClackShack 2 жыл бұрын

@@Mark-oj7yt , I am not against it but currently, I stay busy enough with my current configuration. My 3rd machine will likely be a larger one. I suspect that the other axis will soon get an upgrade as well.

@Mr.Peach90 Жыл бұрын

They make left handed saws!?!?!!?

@TheClackShack Жыл бұрын

Yes, toolguyd.com/right-handed-vs-left-handed-circular-saws/#:~:text=Worm%20drive%20saws%20are%20typically,used%20have%20been%20left%2Dhanded.

@EtchinAaronslaserworkshop 5 ай бұрын

Just trying to get rid of smell of wood I'm cutting smoke is going out but can still smell hint of wood smell

@TheClackShack 5 ай бұрын

Your burning wood. You may smell it

@EtchinAaronslaserworkshop 5 ай бұрын

@@TheClackShack what about wood fumes though??

@EtchinAaronslaserworkshop 5 ай бұрын

@TheClackShack I smell wood burning but I do exhaust smoke out my wall an straight to outside

@EtchinAaronslaserworkshop 5 ай бұрын

@TheClackShack just always smell the wood burning is all that's normal??even with an enclosure

@EtchinAaronslaserworkshop 5 ай бұрын

Was going to say if my exhaust is 4inch shouldn't my inlet be 4inch my enclosure is the size of yours you first made it fits the 400x400 frame

@TylerAvakian 2 жыл бұрын

I want to make one for my xTool extension kit that is coming in soon. But not sure if I want to make an enclosure that big since I'm not always cutting that large. Thoughts? Is it worth making one that large and just always cutting in it? It would be just over 3ft.

@TheClackShack 2 жыл бұрын

If you have children or bystanders around, I would for safety. It does help a lot with fumes and smoke. It also keep environmental dust out.

@MariusAAndersen Жыл бұрын

Thank you for a another great video! Do you have any worksheets for this? If you have, please send me a message! Best regards from Norway !

@TheClackShack Жыл бұрын

A follower drew one and it is on my website. TheClackShack.com

@MariusAAndersen Жыл бұрын

@@TheClackShack Thank you! Keep on streaming!

@I-LOVE-EARTH Жыл бұрын

I don't understand why people insist on making enclosures that only leave a small space around the perimeter of the laser. I left a lot of room around the perimeter to allow for future upgrades and purchases.

@TheClackShack Жыл бұрын

This one is plenty roomy at 26 inches inner.

@I-LOVE-EARTH Жыл бұрын

@@TheClackShack 1 inch clearance on the sides...LOL! 🤣🤣

@texmextrol 2 жыл бұрын

So at 7:12 you mention you want half the top to be flat but you mark at 12 inches instead of 13. At 5:13 you do mention you're going to mark at 13. Haven't finished the video so I don't know if you caught it when cutting but I figured I'd comment now before I get sidetracked with something else and forget about it.

@TheClackShack 2 жыл бұрын

Yea, I am used to the 24x design. It still works. The machine is only 24” so the camera will still be close to center with the machine pushed to the back.