Ender 3 V2 vs BIQU B1 head to head review

Рет қаралды 147,425

Күн бұрын

The Ender 3 was a hit, so which printer is best to succeed it? The Ender 3 V2 and BIQU B1 are both upgraded Ender 3 style 3D printers, which have been put to the test in this review.
Personally, I prefer the appearance of the Ender 3 V2. I prefer the mainboard and removable bed of the B1, however. Both of these printers are closely matched.
Both of these printers were supplied free of charge for review by the manufacturers. All opinions expressed are my own.
Purchase the Ender 3 V2: www.creality3dofficial.com/pr...
Creality Ender 3 V2 (Amazon): amzn.to/3eVes8r
Purchase the BIQI B1: s.click.aliexpress.com/e/_d7r...
Purchase the original Ender 3: www.creality3dofficial.com/pr...
Previous Ender 3 V2 vs BIQU B1 initial impressions video: • Ender 3 V2 vs BIQU B1 ...
My Ender 3 playlist: • Ender 3
SunShine print in place engine video: • Print in Place Engine ...
Models featured in this video:
SunShine Print in place engine STL: www.thingiverse.com/thing:457...
Twist gear vase: www.thingiverse.com/thing:31722
Business card embosser: cults3d.com/en/3d-model/tool/...
Reversible Flexy Bracelet: www.thingiverse.com/thing:138...
Spring clip - ABS version: www.thingiverse.com/thing:139...
Phrozen Sonic Mini vat base: www.thingiverse.com/thing:433...
Part cooling torture test: www.thingiverse.com/thing:316...
Buy quality and affordable filament from X3D. Buy 3, get 1 free and a free sample pack with every order: www.x3d.com.au
Get Quality Resins from 3D Printers Online. 5% off storewide for Teaching Tech subscribers [Code: tech5]
3dprintersonline.com.au/
Take a look around and if you like what you see, please subscribe.
Support me on Patreon: / teachingtech

Пікірлер: 423

@TeachingTech 3 жыл бұрын

Thanks for all the comments! Some common points and FAQs: The gloss filament is here: www.x3d.com.au/store/product/85597-silk-gloss-pla-1-75mm Reading through the comments, it seems some people love the Creality glass bed, plenty had issues like me. I did clean it plenty with 99% IPA as instructed but it made little difference. It can be turned upside down or replaced easily with a spring steel sheet if so desired. According to the comments here, the consensus on the new PSU for the B1 is the same as used by Creality when not using Meanwell. Not amazing but better than unbranded it seems. Oh, and B1 configs are also available for free for Marlin. Thanks Devs!

@dasauto7346 3 жыл бұрын

Heya, got my B1 and looked at the hotend in person and in your video. Do you think there's any all-metal hotend that you can drop in or will some funky adapter work be necessary?

@Allavalle5656 Жыл бұрын

just got the BIGTREETECH B1 SE Plus for $135

@timd9430 3 жыл бұрын

5:26 You should break this out as a seperate video solution as SO MANY have this problem thinking it's elephant foot and looking for help.

@0xmricemanw426 2 жыл бұрын

I didn't read all the comments, so this might be in here already. I had the same squashed bottom layers issue as in the video. Loosening the larger nut on the non-screw side fixed my issue. I also had the same issues with adhesion. I fixed that by using 4 clips instead of just the 2 that were supplied. Placing the clips 33% in from the edges on the front and back. This took the bow out of the bed and gave me a nice flat surface to level.

@davesmith9325 3 жыл бұрын

You are by far the most modest unbiased authoritative and trustworthy channel I have found. Enormous respect & Thankyou. I find the enormous number of unable parameters in cura, and the hassle to hack firmware etc all too much, I just use my printer "out of the box" but even if I dont do most of what you present in your videos its fascinating to hear about all this stuff, helps me understand. Thankyou

@MauDib 3 жыл бұрын

Great video as usual Michael!

@obebodd5066 3 жыл бұрын

Nice to see this video, just got my Biqu b1 2 days ago. Not disapointed! Highly recommend it to anyone

@AhmadLafi-TheFirst 3 жыл бұрын

Do you still recommend this printer?

@obebodd5066 3 жыл бұрын

@@AhmadLafi-TheFirst depends on hos much you like to tinker, it's cheap and sometimes you get what you pay for. Cheap fans in the chassis that starts rumbling and so on. If i were you I would take a look at Biqu BX at kickstarter instead. :)

@Apophis-en9pi 3 жыл бұрын

@Teaching Tech Love your videos! Have you considered putting timestamps in the description for easy access? I think it would help a lot of us out in navigating your videos. Keep up the great work!

@TheMidnightSmith 3 жыл бұрын

Good honest review. No punches pulled, highlight the improvements, excellent. This is what I like to see.

@munkpuppy 3 жыл бұрын

Great video, as always! A tip for using the BTT touchscreen: to change between screen modes, instead of holding down the dial, you can also just hold your finger on the screen!

@chrissavage5966 3 жыл бұрын

Another informative video Michael, thank you. Apropos ABS, I recently tried some for the first time, Ender 3, Creality glass bed, no enclosure, Microswiss hot end. Printing at 245/100 I'm getting surprisingly good results. Initially had adhesion problems but found as long as I clean the bed before each print it's fine. Did get some corner lifting but not excessive. Also just tried the same objects with the same settings but using ApolloX after your review - nice. Almost perfect with only very slight corner lifts. All that to say, odd that you couldn't get the V2 to print ABS properly, particularly given your significant(!) experience and expertise.

@MaxMatrixMan 3 жыл бұрын

Very informative video! Helpful in purchase decision.

@rodneybosco7376 3 жыл бұрын

I view both of these machines more as competing “E3 platforms” than standalone appliances. My Ender 3 Pro has BTT board and display upgrades as well as refinements from other part manufacturers. Bed adhesion and leveling, as well as Cura configuration tuning, seem to have more impact on the 3D printing experience than any distinctions in the basic unit designs. As long as both makers can stay in business over the long haul, you should be fine with either choice.

@billkaroly 3 жыл бұрын

An Amazon B1 reviewer mentioned his heated bed connector was charred after a few months of use.

@parkergipson4269 3 жыл бұрын

My ender 3 v2 had a problem with prints sticking. I flipped the build plate over and printed on the glass side at 60C on the bed. Now everything sticks a lot better. A bigger nozzle size also seems to help with adhesion to the build plate.

@Dendracide 3 жыл бұрын

On my Creality glass bed nothing would stick until I cleaned it with some IPA on a paper towel. Every dozen prints or so I clean it again and never have adhesion problems

@boggisthecat 3 жыл бұрын

Twoheadedpanthr It’s what I do. I have noticed that a low ambient temperature will cause prints to lift at the edges. I mostly run the bed at 60 degC and use PLA.

@ralakus8784 3 жыл бұрын

On my Ender 5 plus, I just remove my build plate, take it to the sink and hand wash it with lukewarm water and dish soap. Works a lot better than IPA in my experience

@TheMrRockOn 3 жыл бұрын

One suggestion - turn the glass bed upside down and use glue for printers. From that moment you wouldn't have ANY troubles sticking anything on the bed. Glue like - shorturl.at/kpLPW

@danielhaqim5284 3 жыл бұрын

use paper glue to your bed, it works for me

@sumorabbit2160 3 жыл бұрын

I flipped my v2 glass bed as I wanted smoother bases. I start my bed off at 60C for the first layers then drop it down to 50C. I also use a bit of PVA glue stick on the bed as well. The PVA cleans off with a little hot water and washing up liquid then a quick wipe down with IPA and a fine microfiber cloth. Still new to 3d printing and only used PLA so far but this seems to work pretty well for me.

@SanSan-vy5zg 3 жыл бұрын

Thanks to this I bought my own biqu B1! No regrets and prints great right off the bat!

@NadDew 3 жыл бұрын

how your experience with it so far? do you still recommend it?

@scottzukowski4294 2 жыл бұрын

@@NadDew I’ve had mine for a year and a half and have had very minimal problems. And those problems were my fault anyway lol. Over all I will always recommend the biqu. It’s just the best one I’ve had.

@AndrewAHayes 3 жыл бұрын

The power runout with a textured glass bed is pointless as the bed will cool and release the print, I made this point on another review of the Ender V2 and some numbscull replied " add some G code to the start code of your slicer to keep the glass hot" and I replied "what is the printer going to run on to keep the bed hot? leopards fanny batter perhaps or some other exotic material"

@TeachingTech 3 жыл бұрын

Gcode to keep the bed on while the power is off; that is a good one. I agree, without the right bed, power loss recovery is useless unless you get to it really quickly.

@yonggor 3 жыл бұрын

sometime it's not blackout but someone hit the power cord or MCB get tripped. In that case, power runout can still save the print.

@F2_CPB 3 жыл бұрын

@Blondie SL Textured or not. Prints will self release as long as it's glass. Unless you apply some adhesive

@F2_CPB 3 жыл бұрын

This is one of reason why I switched back to buildtak. I don't mind prints being harder to remove if I'm getting more reliability. I use a razor blade with handle to get prints off. I will soon switch to spring steel with buildtak

@f_2476 3 жыл бұрын

@@TeachingTech Hi Michael, thanks for the great tips on various 3D printers, I have a request can you make a review about Anycubic Chiron printer because by far I saw that 3D printer suits my budget on buying a large 3D printer... Many thanks and best regards

@janred94 3 жыл бұрын

Great video. Made me keep my original Ender 3 with SKR board. I want a faster responding navigation and screen tho, it is very slow.

@markferrick10 3 жыл бұрын

Great review. I like the opensource code of the BTT display ( I could not find the creality display code source code), the dual function of the BTT display. To me the SKR boards are top notch. However, I am not a fan of the mini adapter interface cards, another point of failure. I am surprised that you had problems with the creality glass bed. I have one on my original E3 (x model) and it works great. If I were in the market today, I think the B1 would get my business. Again, great review.

@avejst 3 жыл бұрын

Great video Thanks for sharing 👍☺️

@michaelhinojosa9665 3 жыл бұрын

Great stuff as always Michael. I am not sure if it was stated but does the BIQU support linear advance? It should right? Would love an Ender 5 BIQU just for the board upgrades!

@gasser5001 3 жыл бұрын

Great review. Liked and sub'd. Got a V2 coming tomorrow already. They seem pretty close in quality and everything. I saw a video of someone upgrading the V2 with a metal extruder and some little things to make it quieter. He was only getting around 40-45dB from it. Overall, they both seem like good options.

@enaliospearfishing 2 жыл бұрын

how is the printer after 6 monts?

@thisiskeithb 3 жыл бұрын

14:14 There's a couple Biqu B1 configs in the Marlin Configurations repo as well 🙂

@TeachingTech 3 жыл бұрын

Thanks Keith, I should have mentioned this. And thanks for all of your ongoing work on Marlin.

@secondc0ming 3 жыл бұрын

I was pleased to find this when I wanted to use the BLTouch for z-axis homing. Compiled my own firmware very easily using those configs having never done it before :)

@thisiskeithb 3 жыл бұрын

@@secondc0ming Thanks for the feedback! I run a slightly tweaked version of this firmware on my B1 with a BLTouch and it's worked great 🙂

@1987jaffa 3 жыл бұрын

I was hoping to hear more about the difference in bed stability. Between that and the glass vs magnetic (which afaik degrades under high temperatures) I'm really torn which one to get as a step up from my da vinci nano

@julsnapple 3 жыл бұрын

nice comparison review between the two! ive been looking to buy a V2 but now i might consider B1. could you maybe do a review on flsun qqs pro? its a delta and the price is similar

@OscarOliu 3 жыл бұрын

Quote of the decade there, "The part exploded instead of coming off"

@thespianmask8451 2 жыл бұрын

A year late, but here's my take about the Ender 3 V2. Funnily enough, I think the problems of the Ender 3 V2 is just the build plate. I bought the printer at around February 2021, and had a crap ton of difficulty printing large objects using the ultrabase part of the glass. I tried printing a model of the Armored Titan, and a corner of the base of the model LIFTED about 8 hours into the print. Small objects were absolutely fine though. I flipped it to the pure glass surface, and prints started sticking well enough. Adhesion was still hit or miss, but I'll take a 70/30 chance rather than no chance with large prints. If I wanted to be ABSOLUTELY sure of adhesion, I would print on a Raft, and it would work 100% of the time. Now, when I ordered the printer, I also ordered a magnetic flex PEI sheet that I never installed because I was afraid I would fuck up sticking the magnetic sticker on the build plate. Just the other day, I installed the PEI sheet, and I had ZERO adhesion problems. It's the third day that I've been using it and holy crap I wish I had just used the sheet from the moment of assembly of the printer. Zero problems at all. PLA sticks so good, it's easy to remove. I'm even using months old green CCTREE PLA filament that I baked to restore it, and the only "problem" the Ender 3 V2 gives me is stringing, but that is more than likely because I'm using ass-old PLA filament that wasn't stored properly.

@ericc8895 3 жыл бұрын

i love your content! Question, if you wanted to keep a budget on a new 3d printer to no more than $400, would you go with the Ender 3 V2 and buy all the mods for it? or would you go a different route with a different 3d printer?

@Patrick_Cooper 3 жыл бұрын

I had the exact problem with the engine model, on my Creality Ender 3 Pro. Trying a reprint now.

@sneaky_tiki 3 жыл бұрын

@Teaching Tech Those ChengLiang PSUs are what Creality has always used on anything that wasn't a Pro version. Having worked with literally thousands of those 360W units, I can say that while they're no MeanWell, they are noticeably more consistent and reliable than others you can source from China. It's honestly what sets Creality apart. Not the PSUs specifically, but they've traditionally done a very good job of finding manufacturers to source their parts. They're cheap, but both the motors and PSUs are good cheap, not regret cheap.

@leonarperro 3 жыл бұрын

Excellent video. I'm currently deciding between this two printers to buy as my first 3d printer. I'm slightly interested in eventually modding it to be used as a PCB carver. Would that be possible with either of these? Thanks for your helpful content.

@Renrondog 3 жыл бұрын

I have an early release Ender 3 V2. The first couple of prints would adhere well , but then nothing would stick. I wiped it down with IPA several times and the paper towel came out yellow. Some type of film applied at the factory to the glass. Once it was cleaned off , a little purple glue stick and everything sticks great, no issues. My Ender3 V2 likes +10* on the bed heater. That said it heats to 70*C in about 80 seconds. Filament heater to 210*C takes a little less time. I'm happy with mine but I was very precise when setting / building to make sure everything was // and square. (90*)

@agentcrm 3 жыл бұрын

I've noticed with our Ender 5 Plus. Disable Eco mode, that should help stop premature seperation, if you're having that issue.

@Pugwash. 3 жыл бұрын

I'm surprised you had adhesion issues on the v2 bed. I'm finding it very good. I only get problems from finger grease that a wipe with isopropanol solves. I haven't used any additional sprays or glues. A BLTouch has also made my first layer perfect, which helps a lot. I did drop my bed temp to 45c but in a colder room I put it back to 60c. The biqu would appeal to me more in black.

@kaimelis 3 жыл бұрын

personally never had any pla stick issues. I have two ender 3 v2s. petg is a bit harder to stick slim parts, but 70 deg temperature and cleaning with strong disinfectant wipes (because theres a lot of them going around these days) makes everything quite smooth. prints pop off themselves when cooled off. a few tips for ender 3 v2 users. flash marlin 2 0 7 firmware, set the bed size to 230 x 230 filament guide is quite necessary. clean the bed after each print. retraction is 5,2 mm for me and 1 mm coast for good outer layers.

@exploitz86 3 жыл бұрын

I've been thinking about to buy the Ender3 v2 but after i've seen this video i had to change my mind. For the same price actually you'll get much more with the Biqu B1. I am a total noob in 3d printing, but i always wanted to jump into. Thank you for this awesome video.

@toaltogaaumi 3 жыл бұрын

how it´s been with the machine?

@BLASTHOCKEY444 3 жыл бұрын

I just got the V2 and I had some similar issues with prints not sticking on the coating. I flipped the bed upside down so that it’s just straight up glass and everything has been sticking great now!

@sumorabbit2160 3 жыл бұрын

I flipped it just because I wanted smoother bases. Still pretty new to 3d printing and only used PLA so far but found starting the print bed off at 60C for the 1st layers then dropping down to 50C seems to work well for me.

@CrimFerret 3 жыл бұрын

I'm seriously looking at one of these for a first printer. Biqu offers a heat break that converts the hot end to all metal as well as a dual gear extruder. I figure upgrading to Capricorn Tubing and maybe adding a BL Touch (or clone) would have me set for a long time to come.

@StevenHess 3 жыл бұрын

Keeping my Ender 3's. The depth of the knowledge base of the original Ender 3 community is second to none.

@myNICKnameISgelo 3 жыл бұрын

that was the one and the only drawback when I was choosing between Ender nd B1

@timd9430 3 жыл бұрын

Yup!

@meganhelker1474 3 жыл бұрын

As someone trying to figure out which printer to buy, this is huge. Deciding factor

@Onerabidmonk1 2 жыл бұрын

Bought an Ender 3 Pro and hate it. Bought a Prusa Mini and it is amazing. I don't want to continually fix my 3d printer, I want to print.

@MrRevolverkiller 2 жыл бұрын

@@Onerabidmonk1 i was gonna get the mini but decided to get the B1 instead. it boiled down to cost, as the B1 was half of a mini. now i REALLY want a mini but i can get 2 B1s for the cost of a mini. im ordering my second B1 next week. anyway so far the B1 has performed awesome. still want a mini tho

@EggChen6DemonBag 3 жыл бұрын

I think I'll be going with the BIQU B1 in a month or 2. will be my 2nd 3D Printer. I have the Ender 3 Pro right now.

@ronaldjobstl9912 3 жыл бұрын

what hotend is the B1 using? and what nozzle? can't find any infos about this. thank you

@Frank-bc8gg 3 жыл бұрын

Great vid! Of course it comes out after I already bought an ender 3 pro and have been tearing out my hair for a week.

@timd9430 3 жыл бұрын

3d printing is a learning experience no matter which printer you purchase even if you buy a Prusa mini. The Ender 3 PRO is a great printer. Don't worry, you'll stop pulling your hair out soon enough. ; )

@Onerabidmonk1 2 жыл бұрын

I bought an Ender 3 Pro and Prusa Mini+ in the same week. The only thing I've had to do to my Mini is clear the nozzle which was the filament needing a hotter nozzle temp. My Ender 3 Pro has made 3 finished prints total in 3 months. I hate it, I spend so much time trying to fix and tweak it. The only good thing about my Ender is it has taught me the mechanical parts of a 3d printer and I'm learning how to work on them. Meanwhile my Mini just cranks prints out.

@thisolman 3 жыл бұрын

To get ABS to stick reliably, Coat the plate with Acetone in which a small amount of ABS has been dissolved. Renew between prints by redistributing the remaining ABS with clean acetone. Once in a while, new dissolved ABS can be added. This sticks so well that the bed must be cooled to easily remove the print. For PLA ( I use separate plates) simply clean the plate with 91% rubbing alcohol. I use these build surfaces exclusively on my Ender3 Pro. I killed the magnetic surface with too much heat and removing while hot. BTW, I have removed some of the textured coating accidentally with prints that have stuck too well and not waiting until the bed was totally cooled.

@diycnc3442 3 жыл бұрын

That B1 looks the goods. The main board, touch screen and upgradeability options are a big selling point out of the box. 👍

@reasonablebeing5392 3 жыл бұрын

To test bed adhesion, I'd like to see is a warping test where you print 20 layers or so of a long narrow print - those are the toughest prints to keep from warping. Try them with and without a 10 or 20 concentric ring skirt.

@jeffcolhoun 3 жыл бұрын

I had that exact same cheng liang power supply come with an ender 3 v1.

@AnishKumar-zq9vx 3 жыл бұрын

Can I use the upgraded board on the ender3 V2 on my ender 3?

@judhi 3 жыл бұрын

Thanks for the great video. Although I own an Ender 3 v2, I clearly see here that B1 is the better printer as it produces more consistent result. My Ender 3 v2 gives me all the same issues shown in this video and the most annoying one is non sticky bed. If B1 doesn't come in that silly pink trim color I might have chosen that 😁

@matejmedved5823 3 жыл бұрын

you can order black one

@alexandermorris2335 3 жыл бұрын

The creality glass beds are amazing. You just cant print to them the same way you would with a buildtak surface. For PLA, i was having adhesion problems at first, but fixed it by doing the following: Clean with ammonia based glass cleaner or IPA, in slicer set the first layer bed temp to 70 and first layer hotend temp to 210, then ramp down to 60/200. Turn fan off for first layer. Thats it. Not hard, just some small tweaks. No gluestick, no hairspray, no tape.

@MrWrieden 3 жыл бұрын

please can you do a video on how to change the loud fans on ender3v2

@User-cl8mn 3 жыл бұрын

Great video!! Loved this. Bought the V2 and comes Friday. My first printer. Would love to see the BLTouch and filament sensor install especially for someone who’s a beginner, many videos I’ve seen on KZfaq really don’t make it simple for beginners in terms of how to get into the code. Can’t wait to see it

@omtapkir8639 3 жыл бұрын

I just searched after seeing just vlad.. And your video came up😂i thought i didnt subscribed you

@Drozas91 3 жыл бұрын

Are you going to review the lotmaxx shark? it is a similar ender 3 clone right?

@unknownsidewinder9945 3 жыл бұрын

@Teaching Tech I still can't decide, what printer would you recommend more?

@MrRevolverkiller 2 жыл бұрын

ive bought the Biqu B1 and have had it for about a week now. Im printing in PETG for the first time and am preparing to print the TPU bracelet. I have been using the stock Cura profiles and was wondering if that was sufficient and if not, what were the temps you adjusted to get it to print right?

@childereena Жыл бұрын

Hi! I'm new to 3D printing and I am using a Biqu B1 printer. Your video was very helpful. Thank you. May I know what tools you use to remove excess PLA from the printed model?

@dean5244 3 жыл бұрын

Please do a video with the necessary upgrades so that the Biqu B1 can utilize linear advance. The stepper drivers are TMC2225 and are not compatible as I understand.

@SidneyCritic 3 жыл бұрын

The jamming at the bottom seams like the columns aren't parallel. Did you tighten the bottom column bolts when the Y gantry was at the top, ie, the bottom columns were free to spread out. It's like car suspensions, ie, you put the car on the ground and load the suspension before you tighten the rubber mounts or you can tear out the centres.

@OinTaylor 3 жыл бұрын

Someone already mentioned but the upgrade power supply they sent from Cheng Liang, that's the same brand as the Ender3 I just opened from Creality official shop for $155. Unknown if it will be a better supply from this manufacturer.

@EggerJonathan 3 жыл бұрын

Any update 5 months later on the B1? I was looking at the 3v2 as my first printer but the B1 looks like a better deal

@dean5244 3 жыл бұрын

I purchased the BIQU B1 and it has not lived up to the hype. Heavy z-banding and the steppers don't allow for linear advance. I get better results from my old Ender 3 pro and Artillery X1. I feel as though I should have went with the Genius based on the good luck I had with my Artillery X1.

@dean5244 3 жыл бұрын

Can you post the profile or basic settings that you used for PETG?

@Maltduck100 3 жыл бұрын

I got a ender3 pro with a skr minie v2 and a ezr extruder and it works grate all i need is a bigger build plate as the 235/235 is just a shade too small

@myNICKnameISgelo 3 жыл бұрын

The problem that I have on B1, ( that dont mentioned by anyone who reviewed the biqu b1) is the bed adhesion. I thought it was bad cooling fan duct, but I did that same cooling test and got same result. The fans are blowing partially on the bed.

@zacharywilliams9122 3 жыл бұрын

Something you may want to try is rubbing the bed with 90% IPA, you'd be shocked how much that can affect adhesion on a lot of beds

@juan-he6pm 3 жыл бұрын

Hello, which one do you recommend more for a beginner, thank you.

@sketch088 3 жыл бұрын

I just got my first 3d printer (ender 3 v2) not to be biased but I have had zero issues. Prints come out great. The bed adhesion is perfect. For a 3d printing KZfaqr you didn't seem to care about figuring out what was wrong with your printer. Seemed very biased towards the b1.

@gloopann 3 жыл бұрын

Same here, i literally just leveled the bed and I clean it with alcohol every few days and the prints stick really well, if not too well... Sometimes I have to wait an hour until I can take the print off the bed

@699hazard 3 жыл бұрын

I've been looking at purchasing a second printer and I think you have convinced me to get the biqu.

@Sebazzz1991 3 жыл бұрын

BIQU is going to eat Creality for lunch - Creality did a bad one with the CR-6 Kickstarter and the competition is increasing.

@patricknein9062 3 жыл бұрын

@@BlockiBiz I've got two creality enders now. Both work great.

@dean5244 3 жыл бұрын

I purchased the BIQU B1 and wished I'd purchased something else. Didn't live up to the hype for me. Z-banding issues, can't use linear advance due to the stepper drivers, and lack of community support.

@draconisdei 2 жыл бұрын

I'm late to this party, but seem to be having a lot of trouble with my B1 only 2 days after having it either I got a messed-up model or its the filament but I think ima have to return it and get an Ender 3 but thanks for the video it helped a lot in terms of which to get.

@nic2154572 3 жыл бұрын

Will the ender extender work on the B1?

@henriquelopes5080 3 жыл бұрын

Does someone know if the B1 has the same hotend as the ender 3? I'm curious if I could use an all-metal hot end made for the ender 3 with the b1

@Artnovetor 3 жыл бұрын

Parabéns 👏👏

@flex-ranger2 Жыл бұрын

Chopper read style pose 3:16, dont know if deliberate but still hilarious 🤣

@JeanLucCoulon 3 жыл бұрын

A BIQU B1 with Marlin video would be nice!

@the_equalizor 3 жыл бұрын

I love my v2, but I had a real issue with the extruder motor getting so hot it would cause the filament to melt after the gears. Checking the Vref on the extrude steeper pot, it was set at 1.7v which is way too high. Bringing it down to 1.38v fixed the issue for me. Other than that it’s a great set and forget printer for me.

@klave8511 3 жыл бұрын

The Equalizor : That’s a great observation, well done for digging in and finding that. It should be one of the checks we do when we get a new machine, feel if any steppers are getting hot or better yet measure the temperature when doing a standardized print.

@the_equalizor 3 жыл бұрын

Klave Absolutely. It’s quite an easy and safe thing to do as no mains involved in that area. I took the stepper figure from my ender 5 pro, and I’ve seen them since in a document from Creality. It’s still a great printer, very glad I bought it. Now if I can just get my head around supports on resin printing I’ll be just dandy :)

@the_equalizor 3 жыл бұрын

@@kevinlu6596 The steepers arn't UART controlled so they cant be programmed "remotely". You need to remove the bottom panel to get access to the mainboard pots. This is something that doesn't need doing unless it's causing an actual issue with filament melting in the extruder gears or the motors are getting too hot to touch.

@jamesmoe 3 жыл бұрын

You mentioned in your BIQU B1 video(s) that you were going to revisit the BLTouch and possibly other enhancements. Do you have that video in the pipeline? I have the BIQU B1 based on your review and think it wins out over the Ender 3 V2 handily. Adding the BLTouch does not; however, appear seamless just because they provide a bracket. Having a bit of an issue .. such as what do I do with the Z endstop after adding the BLTouch. In any case I look forward to future videos about that BIQU B1. I very much enjoy your channel and believe you provide the most comprehensive and practical information.

@jamesmoe 3 жыл бұрын

So I got the BLTouch and it is really giving me fits. Would love to see beginning to end setup after installation.

@Mrdelllol 3 жыл бұрын

What type of filament does he use in this video?

@ojcustom 3 жыл бұрын

Do b1 have a larger bed upgrade kit?

@hathzorz 3 жыл бұрын

Why does legacy mode for the TMC2208s make them incompatible with linear advance? I've seen some conflicting info on whether it might work. A forum post on RepRap says on Marlin 2.0.x you can set MINUMUM_STEPPER_PULSE to above 1, or use spreadcycle instead of stealthchop since stealthchop is unreliable with lin adv. Newer Marlin supposedly fixes the too-short stepper pulses problem that might've happened in the past. I personally don't know one way or the other so I'd love to hear your thoughts.

@TeachingTech 3 жыл бұрын

I tested it once (can't remember which printer sorry) and found my result matched what I had read. The extruder stepper stopped turning early in the print, no errors or warnings. The TMC stepper library is supplied by the community, it might be some sort of compatibility issue with that.

@oonie99 3 жыл бұрын

My ender 3 v2 has a nonworking SD card reader out of the box. More than 2 months later and the replacement still hasn't been sent from the seller so I have to run it from a computer all the time. Fans are loud and you will have to do some work and spend money to fix that. The bed was getting worse over time with not sticking so I invested in some 3DLAC Plus. It's not cheap but you only need a little bit and my troubles have ended. No more failed prints and cooling the glass plate releases the print. Worth every cent considering how much time and PLA it' saved me. I'll stick with the ender for now as the prints are excellent and the machine is reliable. The only thing I have noticed lately is the poor quality of some PLA's. From bad winding to brittle or inconsistent size, the situation this year has not been good. I now only buy from a trusted supplier and have to pay more for it.

@S0Fr3shThisKid 3 жыл бұрын

I buy my PLA from Matterhackers...free shipping always!

@oonie99 3 жыл бұрын

@@S0Fr3shThisKid I recently tried x3d.com.au based on the advice of teaching tech and have also found it to be great quality. You do have to order $150 (i think)to get free shipping, but at least it prints well and doesn't jam. I'll check out matterhackers for the smaller orders though, thanks. Now that I have quality PLA I find the ender to be super reliable and consistent for the prints.

@S0Fr3shThisKid 3 жыл бұрын

eSUN PLA+ is some of the BEST PLA I have ever printed with! I ordered it from Matterhackers...the FiberForce Pantone PLA is 🔥🔥🔥 but it's also expensive AF

@lylebraybrook275 3 жыл бұрын

I too had a bad bed so I brought a borosilicate glass bed from amazon and have had no issues since then

@jon9947 3 жыл бұрын

I pretty much think that as long as the pla is wound decent and dry then pla is pla, and the cheapest stuff you can get is the best way to go. I have been having really good luck with 3D Solutech white, its $16 a spool on Amazon. I was buying a different brand before the world turned upside down and the filament makers started to raise their prices. I will admit that I think the previous brand I was purchasing is slightly better pla, but it is not $10-$15 better, it is not even $5 better. So as long as 3D Solutech keeps sending me spools that are wound good, I am going to keep buying them. The only downside with the pla I can say is it seems every so slightly smaller of a spool, but I dont have a scale and that could just be my imagination. It is also frequently out of stock so I purchase 5 or so spools every time I am running low.

@CasteraPrn 3 жыл бұрын

I just ordered Ender3 V2 and this well made review made me nervous. Thanks anyway.

@hug00l 3 жыл бұрын

tssssss

@MattMontanez 3 жыл бұрын

How are you liking your V2? I ended up returning mine that I ordered. Unfortunately it had a bad motherboard and when I did get it running I got one successful print out of about 50. A lot of issues with the one I received.

@spongecounter 3 жыл бұрын

I have been really happy with my Ender 3V2, so don’t worry about it too much. I have been getting loads of great prints out of it. In fact it has paid for itself 3 times at least, compared to the parts I used to have machined. I have also been having a lot of fun modifying the V2, which has really helped me to learn. Run Michael’s (TeachingTech)tuning website procedures on your machine to tune it. Switch from the Creality firmware to the Marlin Ender 3V2 firmware custom compile with linear advance enabled (marlin.crc.id.au). And use the fast live leveling technique to tram your bed, it works really well to get the first layer to adhere every time. You will need to relevel for each new bed temperature (I.e. PLA vs PETG). Over time I noticed the centre of the bed sagged. I tried flipping the glass over but it still sagged. I shimmed the centre under the glass with aluminum foil tape and now the bed is flat. Good luck I hope you enjoy your machine.

@MONTY-YTNOM 3 жыл бұрын

I hope BIQU work on the firmware better than they did/do with the Thunder .

@nathankennedy2436 3 жыл бұрын

I was having problems with the print not sticking too the bed after a heap of good prints after washing the glass bed in hot soapy water the problem went away so now i just wash the glass bed every few prints

@03jalapeno Ай бұрын

I had the same issues with the ender 3 v2 bed. I replaced it with the Bigtree tech heater bed and powder-coated pei bed and it works much better.

@copperninja5248 2 жыл бұрын

hey can you help me i got the bibq1 and when i try and home it does not move and said printed halted kill called please help

@vladimirjar3800 Жыл бұрын

you should review the voxlab aqula next and compar it to the ender 3 v2.

@johnnyto2141 3 жыл бұрын

Hey, can you please make a video that describes how to fix elephant foot?

@BillYovino 3 жыл бұрын

You can fix that with a new setting in the latest Cura.

@ja-no6fx 3 жыл бұрын

seems like the b1 won in every aspect...

@dieselaegean 3 жыл бұрын

Until something fails and you can't find support and parts

@josephgrn2818 3 жыл бұрын

Biqu B1 now has power recovery resume. Tricky since it has to be fast as the hot end is....hot

@ILoveFood0911 3 жыл бұрын

I got an b1 as my second printer

@jassimann5486 3 жыл бұрын

Paid review . Realy ceap build quality. Bed warped in two or three days . Hot end assembly bobble by forces of type c cable . Fans are shit . Making laoud noise Bed is not sticky. After some time power supply fan creating vibrations.

@josephgrn2818 3 жыл бұрын

@@jassimann5486 is this your first printer?

@nicholasgenzman4213 3 жыл бұрын

There so call “upgrade” PSU isn’t good either. It’s the same one that comes in stock CR10. Not a good and reputable brand. Just stick with the Meanwell

@DaneSaysStuff 3 жыл бұрын

Yup. I'm sold on the B1. And unlike so many others, I'm not going to cry my eyes out because it's pink.

@secondc0ming 3 жыл бұрын

It's actually not as bright as it looks on camera either.

@EggChen6DemonBag 3 жыл бұрын

I'm into Retrowave so the BIQU B1 is perfectly fine for me.

@myNICKnameISgelo 3 жыл бұрын

so why did you sold B1?

@daniel-goodwin 3 жыл бұрын

I had a 3 Pro for a bit before I swapped and got a 3V2. Can see the benefits of the BIQU but it also seems like I lot of your quality comparisons were based on what possibly was a bad V2 machine. I’ve had no issue with adhesion or any of the build quality. Using stock ender 3 profile (not even the pro version) out of the latest version of Cura. I wonder if you had one that was performing as well as mine seems to be if the quality comparison wouldn’t have been such a wide gap.

@TeachingTech 3 жыл бұрын

You'll notice I was transparent with the issues I had but at no point did I bag the Ender 3 V2 as a bad printer. The Z compression/alignment problem could happen to any printer depending on the V roller tension during shipping. The bed was the only real persistent issue. Worst case would be to flip it upside down and use the plan glass side with hairspray or glue stick ,etc.

@daniel-goodwin 3 жыл бұрын

Teaching Tech sorry if that came across overly critical, wasn’t meant to be. Just was trying to say a comparison where both of the machines seemed to be more error free would be ideal. I haven’t been 3d printing for long, but I have learned that even amongst the same machine there can be a lot of variance. Some problems some people have others don’t, conversely you might see things others don’t. As an entry level machine they both seem great and I’ve been churning out some pretty solid prints with my V2. I had actually watched your first take comparison video about a day before buying the V2 and I almost went with the BIQU but was a little concerned about the generic PSU. All in all still happy with my decision though 👍 thanks for the great content, really have enjoyed your channel and learned a lot from so many of your past videos.

@carbide1968 3 жыл бұрын

I am by no way someone who could suggest anything to a expert like yourself but by chance were you using isp to clean the glass? I found if you use at least 91% parts stick perfect every time. I found lower percents leave a film and parts always break free. This is just what i experienced so far. Great video as always sir.

@TeachingTech 3 жыл бұрын

I did use IPA, but it was 99%.

@Dingmiester 3 жыл бұрын

Hi all, So I am looking at getting my first Printer very soon. I have watched soooooo many Vids and read so much about them all, Until now I was set on a Ender 3, Then a Ender 3 Pro, Then a Ender 3 V2 and now the BIQU B1. I can see the pros and cons to them all, but it does seem that the B1 seems to be a great printer out the box. It looks like it hardly needs any upgrades if any. I am happy to learn and mod anything so getting my hands dirty is not an issue. The one thing everyone talks about is the PSU needs to be a MW one or should be, are they not interchangeable?, so could you not get a MW one and put it in a B1?. Sorry if thats a daft question. Is the B1 new on the market as there is not to much about them, like printed upgrades and just general info about them that's my only concern about the B1. Yes Im confused now lol, HELP ..... cheers peeps... keep safe ....

@Dingmiester 3 жыл бұрын

@Parminder Mann I went with the Biqu B1, tbh although I new nothing about printers, I have found Bique easy to use, set up, get to grips with and get some great prints so far, so I am very happy with my choice. I can't comment on the Ender as I have not got one and I am sure that is just as good .

@mohammedalhelal2956 3 жыл бұрын

@@Dingmiester I am in your same situation from 2 months ago... I am buying it for my brother. Do you regret your decision ... are there any hindsight thoughts?

@Dingmiester 3 жыл бұрын

@@mohammedalhelal2956 No regrets with mine, but I was lucky with my one it seems. Its a common problem with the biqu to have an uneven bed, the firmware needs to be updated ( its easy to do) eveything needs to be checked over but im sure that is normal with all printers. I had to get a glass bed to improve adhesion and get a level bed. One thing I know now is this hobby needs A lot of patients and time to get decent prints. If you have face book join the Biqu group to get more of an Insight into this printer. But remember most people that comment on these sites have problems and want to get info on how to sort it out. Hope this helps and don't be put off they are great fun. If your brother has time and patience he will love this printer. Big plus on the Biqu B1 is the Touch screen .

@CMDRBlueeagle66 3 жыл бұрын

The buildplate on the B1 releases when cool. I find that the base on the B1 acts like a guitar and amplifies noise on fast moves. But not too bad.

@noahfremont6310 3 жыл бұрын

It does a perfect job of that. When it cools down, it releases so well that I could blow on it and it would move.

@CMDRBlueeagle66 3 жыл бұрын

@Teaching Tech Apparently the B1 does have power loss recovery. A chap on the FB B1 user group confirmed it.

@Krytern 3 жыл бұрын

On the Ender 3 v2 the print releases off the buildplate when it cools as well. Not sure why this channel has had trouble with bed adhesion though it has been sticking on mine fine.

@andywakeman3395 3 жыл бұрын

@@Krytern I bought Creality's glass bed and haven't had a successful print yet, first later failing to bind every time.

@gcantu05 3 жыл бұрын

I have the ender3 v2 and have been very pleased so far. No prints have failed and it's easy to remove the print when it cools. Honestly the only reason I bought the ender instead of the b1 was because I could pick it up in store and the wait for the b1 was a month from bang good.

@tvideo1189 3 жыл бұрын

Surprised you gave the Ender a bye on the bed adhesion problems.

@maunladbalesandusedclothin3227 8 ай бұрын

i know it's an old video but can you help me to flash a new firmware for the biqu b1

@TheJagwtf 3 жыл бұрын

@Teaching Tech I know you are more qualified than I am, as I have learned a lot from your videos. But i would suggest returning to the Ender 3v2 and looking at it again. I purchased an Ender 3v2 when it came out, and I have none of the issues you have. No bed issues, everything sticks lick a charm, no extrusion issues, no blobbing issues. Printing ABS was plug and play - both small and large parts, as well as "vase mode" with 3 layers. I love your video, but it does not do merit to the Ender 3v2, This was my first ever normal 3d printer (before i used a Makerbot Replicator Mini), and it was assemble, have issues with the Z Axis, fix it, and zero errors since.

@TeachingTech 3 жыл бұрын

We can both only judge what we have in front of us, it's not fair to speculate. This is why I always suggest looking at a range of reviews to get a broader picture.

@AllInnerLove 3 жыл бұрын

Do flex3drive on ender 3.

@praesil8136 3 жыл бұрын

I have the same bed on my original Ender 3 pro, and have similar issues with sticking. Is there an easy way to address this that anyone has come across (perhaps flipping it over to the glass side and using gluestick?) or is it easier to just go with a PEI sheet and give up on the ultrabase?

@BeezyKing99 3 жыл бұрын

Bump it up another 10° or so... fans blow on the print bed cooling it off a touch at the start... I have the same one as you do.. although I do have the magnetic flex bed... works for me no problem since I bumped my temp to 68° for the bed

@T4nm4y 3 жыл бұрын

Why is it not compatible with linear advance? 🤔

@tonysaporito71 3 жыл бұрын

Would the Ender 3 V2 benefit from having TL smoothers installed?

@paulthetexan 3 жыл бұрын

Doubtful, because they already have silent steppers.

@jakoj2098 2 жыл бұрын

I thought everything upgradable for the B1 would be same availability for V2 as the B1 is pretty much a Ender anyway?

@lylebraybrook275 3 жыл бұрын

Looking forward to that ender 3 v2 bl touch video

@woodypride1750 3 жыл бұрын

Same, I fought with trying to get the BLTouch set up on my V2 for about a day and a half before I gave up. I also have a Micro Swiss DD extruder and hot end on mine now too though.

@Pieterv24 3 жыл бұрын

@@woodypride1750 I got it working after some fighting with it, and some bug hunting in Marlin

@hermansd1 3 жыл бұрын

I got my bltouch to work with V2 as well. It was a full day of trial and error but it works.

@lylebraybrook275 3 жыл бұрын

@@hermansd1 I'm a noob so I really need something plug in and play as I have no idea how to bug hunt etc and if I spend £40 on something I don't think I could take it not working haha