Engine Freeze Plug Removal

Engine Freeze Plug Removal - The easy way!

Рет қаралды 62,280

3 жыл бұрын

I struggled for a while when it came to removing freeze plugs on an engine block, but I can up with this easy method that pretty much eliminated the struggle. Using a drill and a punch gets you set up for the final tool, that isn't used as it was intended, but works perfectly, every time.
If you like these quick tool tips in engine building, or have a tip that you want me to try, let me know and I will test it out on this channel!

Пікірлер: 50

@roguebenim2238 Жыл бұрын

Couldn’t get any better for your advice then bam saw that beautiful FC

@vaclavkonicek5514 Жыл бұрын

Perfect video, excellent and simple procedure. Thank you very much, greetings from the Czech Republic.

@jpm Жыл бұрын

Thanks for watching and awesome to hear us reach out friends overseas!

@D4rkS4v4nt 2 ай бұрын

Excellent - was trying to find out what it looks like, in the Porsche WSM for the 944 it specifies this method for removing the freeze plugs

@travisburgemeister313 2 жыл бұрын

Thanks! I had a freeze plug in a hard to reach area, I couldn’t get a fill in there but I used a carbide on my in-line grinder punched the opposite side to get it sideways and it came out with ease thanks again!

@jpm 2 жыл бұрын

Glad it helped! It's amazing what you can do, when you need to get the car running, huh?

@CBRRR-eh3ky 2 жыл бұрын

How did you put it back

@xoxo9623 Ай бұрын

Brilliant!

@TheMr39 Жыл бұрын

That’s great if you’re rebuilding your engine. How about when you have to replace a leaking freeze plug with engine in the car?

@DeanCook-yn9ek Жыл бұрын

knock it in and it will rot away in the block

@tonyjohnson8205 3 жыл бұрын

Great video

@jpm 3 жыл бұрын

Glad you enjoyed it - Always trying to spread a few of my tricks and shortcuts around!

@charleswittmer2477 29 күн бұрын

nice process, american ingenuity

@wilfredv1930 2 жыл бұрын

Very nice job, what if one scratch a little the seat of the freeze plug? there will be any problem?

@jpm 2 жыл бұрын

That’s a hard question to answer here. Obviously, you want a nice clean surface to work with, but how do you define a scratch? How deep is it? It could need to be repaired. I would invest in making the surface as good as it can be before installing new plugs. If it leaks, it is coming apart again, so might as well do the job right the first time around and only do it once.

@davidstepeck2644 2 жыл бұрын

I guess this works but kind of over engineered in my opinion. If you just tap one side of the plug with a blunt stone chisel or a punch, the freeze out plug will spin 90° and you just pull it out with pliers. So much easier, and you don’t get metal shavings into the cooling system or engine.

@jpm 2 жыл бұрын

Like I always say, not the only way to do it, but it does the job that I have had success with. Thanks for watching!

@oageletserampuleng10 9 ай бұрын

Easier said than done I'm struggling fail to remove it out

@ASpacywalf 2 ай бұрын

My block has a ridge so two plugs cannot spin out

@LegendCampbell 2 ай бұрын

Well lemme tell you why someone would do this!.. a stuck freeze plug won't insert further.. so the hammer trick doesn't work! Now Imma go try this method

@faithgrasso697 2 ай бұрын

Isnt he possibly putting shavings inside by drilling???

@adamzgi55 8 ай бұрын

I'm about to do this on my 95 f150 302 but don't have tools to pull engine. Is it doable with engine in place. Or possibly taking if engine mounts and propping engine up a few inches

@charleswittmer2477 29 күн бұрын

you will only do the easy ones, what about if there are some under the flywheel?

@1budmech2 16 күн бұрын

Yeah lets see that with one still on the block

@justinchristiano7928 2 жыл бұрын

Awesome! Thanks!!!

@Skuggan84 Ай бұрын

And if the freeze plug won't budge using the Hammer and punch method? I have one where I hit as hard as I can and the damn thing just doesn't move at all.

@coryjordan2368 Күн бұрын

working on a mid 70s bbc 454. i had some that were punching holes in the plugs (wouldnt budge). i ended up pushing the plugs into the water jackets with a similar sized socket. and finagling them out. hope it helps.

@coryjordan2368 Күн бұрын

soak them in PB. and just keep working. i didnt use the seal puller, i wedged the punch into it and pry'd some of them out.

@Skuggan84 Күн бұрын

@@coryjordan2368 i discovered it rested against a lip on the inside. Self tapper and prybar was the correct solution...

@andredesousa96 3 ай бұрын

No need to drill, just tap with the punch to rotate 90º and pull out with pliers.

@TOMVUTHEPIMP Жыл бұрын

If I could get the plug to tilt that easy I would not have to drill it. Banged on mine with a punch and 5 pound dead blow hammer and it just laughed. They will have to be cut out..

@jpm Жыл бұрын

Sometimes, they are pretty stuck and ease of access is an issue, but for the most part, the way I do it will work. There is always that, "one" that doesn't want to be part pf the team.

@TOMVUTHEPIMP Жыл бұрын

@@jpm I got them out. Just needed more persuasion.

@steveroberson1488 Жыл бұрын

I think I'll try this method but instead of drilling I'm going to punch a small hole

@jpm Жыл бұрын

Possibly a cleaner method - let me know how that works for you!

@jpm Жыл бұрын

Beware, odds are you'll just hit the freeze plug into the cooling galley, making it harder to get out of the block.

@steveroberson1488 Жыл бұрын

Nah I've already punched a hole in two ,,these things are 52 years old & very soft,,but they don't want to come out

@FANABBS Жыл бұрын

Way easier when motor out of car

@johnnyrocketa1257 4 ай бұрын

DO NOT USE CHISELS!!! A bad hit, and the plug will never seal properly. Drill a 8 or 10 mm hole on the plug as centered as you can, thread it with a male tap, get the corresponding bolt with washers, normal and oversized, grab a 1/2 ratchet socket about 2 numbers bigger than the plug (I.e. if the plug is 30 mm use the 32 mils), now put the socket over the plug, the washers, and the bolt screwed on the plug through the socket, and use the ratchet to turn it until the plug pops out. If you have the block on a stand and you can screw a nut behind, you can pull even the most stuck plugs. Heating it also helps. I've replaced quite some plugs this way... But in case it's too stuck, and you can't screw a nut behind, weld a big bolt on it with a washer (12, 13, or 14 mils is enough), and use a sliding hammer. Again, the blow torch is your best friend here😁

@gregbaylin9640 2 жыл бұрын

i think its easy doing it outside,, but if engine still attched to frame i dint think ad easy ad that ,, tnx anyway

@jpm 2 жыл бұрын

As with any tip/trick, it may not work in your situation. Access could be limited to the point that you can’t use this method. There are others though!

@rawfoodphilosophy7061 2 жыл бұрын

Just hit it on one side, and then use pliers or vise grips to grab the lip on the other side and then pull it out

@jpm 2 жыл бұрын

That’s another way to do it!

@Celicagamer 2 жыл бұрын

and when this doesn't work. then what

@jpm 2 жыл бұрын

There are a few other steps you can take, but if this didn't work, you might have some rust issues. The next steps will depend on if the engine is on a stand or still in the car, but that bond needs to get broken.

@dawggonefunny458 11 ай бұрын

@jimmyconn7314 5 ай бұрын

Not worth the probability of getting metal shavings in side engine.additionally if the engine is in vehicle,basically all the drill motors and longer then necessary tools you utilizes are way to long to be of any use.have to give this a hands down report.i rarely do that but come on very non realistic and potentially damaging techniques.