That is a great looking door. Missed your videos the last few weeks. I always look forward to watching them on the weekend. Thank you!

Great video and thanks for the tour of your amazing shop!

I have nothing to say really, but I appreciate your content, and wish to help with the yt-algorithms.

More than one way to do any job great to see different options thanks Andy hope your doing well cheers

Pleasure to watch. Beautiful work

stunning work looks amazing

Nice job Andy, great to see you man🇮🇪👏🏼👏🏼👍👍

Love your set up

Clean sharp and tight - nice job.

A good looking door, and well filmed.😀🇬🇧

Awesome workshop 👍🏻

Good work. I like your collection of machines. awesome

Fantastic work there, Andy! 👍🏽 Door looks awesome and definitely built to last.👌🏽 Getting those bits for your spindle moulder will absolutely help your work flow. Cheers mate, take care.

Great work

Great video.

Beautiful job like your shares.😯👍

your machinery is amaizing for a small shop

Hey, Bosstik makes a lubricant spray called GlideCote and spray it on the cast iron tables (just enough to cover-not too much) and wait a minute before wiping-buffing with a dry clean cloth or paper towel. Then, note how easy it is to push that oak past a blade. The spray does not stay on the wood or discolor you wood. Rather expensive stuff but reduces friction.

Lovely work. New subscriber. Would love to see the finished product displayed at the end.

Great video fella, I like the loose tendon you can't have everything in a medium size shop. It's been a while since I chopped a rebate lock in . 👍

Cracking Job, would've liked to have seen the finished products swinging though!

Great job. It's therapeutic to see the transformation of rough planks into a refined and solid looking door. Unfortunately we can't get the F250 here in Canada. I am curious how you calculated the sizing of your T&G panelling to fit precisely width-wise inside the door frame.

Loved this video. Have you thought about doing a video on your fire situation? How it started, extent of damage, and how your business survived this ordeal. That would be interesting to your viewers for sure.

The monster loose tenons and your mortising machine looks great, and the door does too. I was surprised that you were not using a slow setting epoxy adhesive in the door assembly. If the wood glue starts setting during assembly, it can make assembly difficult and can result in possible weak joints. Water in the wood glue also causes loose tenons to swell, making assembly difficult, too. The slow setting epoxy gives you more assembly time, and it does not swell the loose tenons but acts as a lubricant making assembly easier.

Also remember when your using a rebate cutter like that in the router to ‘reverse first’ to avoid chipping out the bottom edge

Классно

Nice, do you finish the edges on your t&g panel's before you fit them ?.

Nice job! Can you tell me what reference of hinge you are using please. I search fort this sort of for making my doors 😉

Beautiful doors. When the material is flat sawn how much space do you allow for expansion with seasonal movement? I'm in Louisiana, where the humidity is high. I'm wanting to build a set of doors out of white oak flat sawn.

Will you show the finishing method/material with the next doors?

When I got the FD250 along with it we got a 10MM Carbide edge birds mouth bit. That style bit is barely OK for shallow work. Go ahead and get a two wing solid carbide end mill and speed things up radically and get a better surface. The plunge is like diving into a larger swimming pool-smooth and free. Just completed an island kitchen walnut-maple butcher block top 3' X 6' X 2-1/4" with one corner being a 9" radius round corner with band saw rough to a pencil line and then on to the Format 4 shaper with guide rings along a template screwed to the under side. Felder sells (did sell) a 14 knife helical cut 4" height tooling that did such a nice job you don't need to sand it. With ring you want to do a lift off slope on both ends and then blend the radius with 320 grit orbital. I can buy the end mill for less than the birds eye variety. 1500 rpm on the FD 250

Do you use the digital readout when in thicknesser mode?

So when you put the interior panels in, is it just an interference fit? What is holding them in? Just a "press fit"?

Could you make a video of a door out of wood material from Homedepot or Lowes?

If the tongue and groove boards were sat into a rebate the glue up would have been easier. Its also easier hanging the door because you can hang the door without all of that extra weight. You could cut the tenons on a normal block. Just obviously you'd need some sort of carriage to keep the timber square and safe. Through tenons wedged would mean after the wedges are seated you can take the clamps off and carry on working rather than having to wait for the glue to cure.

2 questions.... Why you stoped using Df700 for this kind of job, and did you do a video on aluminium extrusion profile router table and miter saw stand?

Stupid question coming. What do you do with all the saw dust and chippings?

Seems ages since u had some videos out will there be some out soon?

Hey guys do you know what kind of Scissor lift or who makes it? Can’t seem to find one that doesn’t have a handle on it

Great looking door. What a shame the video ends before we see the finished article.

Hello 9724, Your hinges jig router look durable. Sorry can you let me know a website to buy. Is the hinges jig router the same as yours? Thank you.

Are you still going to be posting Andy? Hope everything is ok as it has been a while.

Bit more on the hot melt gun 'running repair' please? What was the 'iron' you used - and that odd looking chisel?

👊👍👌

What on earth happened to your Etsy shop?

2:13 WTF ?!

Tenons a bit snug there fella? 😉

nothing to comment, just for algorythm.

Down votes on informative, well-produced videos like this should require a full paragraph explanation with citations and a registered phone number or street address.

I guess no one taught you that when you flatten a board on the jointer you grab the board on the outfeed table. What you're doing is typical for someone who's self taught.

Das ist aber keine Profi arbeit

Good work but poor safety on machines. Looks very fumbly and cack handed

All the tools and no skills. It's kind of funny watching somebody demonstrate woodworking machinery and it's crystal clear they have no experience using the equipment.