How does the Yaw Load Compensator work

No video

How does the Yaw Load Compensator work

Рет қаралды 10,805

Күн бұрын

Many of the AS350/AS355 models of helicopter have a yaw load compensator. This device is often misunderstood in its make up and operation.
Click Subscribe to be notified of future EuroSafety Videos.
www.eurosafety.us
training@eurosafety.us

Пікірлер: 17

@407instructor8 Жыл бұрын

I train pilots in the B3e and your videos are very helpful. Great content keep up the good work!!

@EUROSAFETYTRAINING Жыл бұрын

Glad you like them!

@EUROCOPTERB3E Жыл бұрын

Thank you for making these excellent videos!

@EUROSAFETYTRAINING Жыл бұрын

My pleasure!

@nigeltindall1446 11 ай бұрын

Great tutorial but I feel like I might have missed something here. I'm wondering why you made no mention of the procedure with regards "Loss of Tail Rotor Control". The RFM states that once 70 kts IAS is attained to activate the [ACCU TST] button, which then depressurises the "Load Compensator". In other words, the load compensator - once depressurised - gives you 5 secs to gain a more neutral position of the pedals, should they be greatly offset. After 5 secs the [ACCU TST] should be reset to off. In my mind, I was under the impression that this was the main purpose of the Load Compensator, but of course I could be completely wrong. I'm keen to gain more understanding, so again, thank you for sharing and thanks for hearing me out. I would be more than interested to hear your comments on this. Cheers.

@EUROSAFETYTRAINING 11 ай бұрын

thank you. I made another video that is an overview of the operation of the yaw load compensator. But briefly... The yaw load compensators job is to help the pilot induce twist into the spar. The reason we depress the ACCU TST button is to dump the pressure out of the yaw load compensator. The compensator was helping hold the twist into the blades. Without that pressure the twist takes itself out.

@adambell8035 7 ай бұрын

Hi Glen, great videos, 3D modeling is awesome… following on with the previous comment, can you elaborate why it is preferred to release accumulator pressure with a stuck pedal but not a servo slide failure? @@EUROSAFETYTRAINING (B3e dual hydraulics) Cheers - Adam

@ishworlamichhane6766 Жыл бұрын

Excellent explanation !

@EUROSAFETYTRAINING Жыл бұрын

Glad it helped!

@averydallaire3458 Жыл бұрын

Thanks again for these videos. Can you explain why we are instructed to bleed off the Yaw load compensator after each flight?

@EUROSAFETYTRAINING Жыл бұрын

If you don't, the pedal will go to full deflection causing stress in the tail rotor spar

@llwellyn1 Жыл бұрын

Does the yaw load compensator have a limited time of utility after the failure of the hydraulic system? If so, what is the time limit? Or is it a limited by how much pedal movement you are making? Say, you're in cruise flight at a power and speed configuration which requires little pedal articulation. Must you land " as soon as practicable " or can you continue until an ideal maintenance location is reached? I'm assuming in this question that the main rotor hydraulics are still operational... You're my new favorite channel. Thanks for making these informative videos!

@EUROSAFETYTRAINING Жыл бұрын

The yaw load compensator will continue to operate until the HYD TEST (ACCU TEST) is depressed after flight, but is only noticeable after a hydraulic failure ( single bodied system) or when you loose right system in a dual system. Did I answer question or did I misunderstand? Thank you for your support!!

@llwellyn1 Жыл бұрын

@@EUROSAFETYTRAINING Yes, you answered the core of my question. Thank you. I suppose I'm still yearning for knowledge on the B3's main rotor hyd redundancy. I know it has twin servos per pitch change link but a solitary hyd source off of the main transmission. Is there a load compensator for the main rotor as well should the main pump fail? Same overall back-up as the tail rotor system? I'd love to see a technical review of the twin servo construction :) Thanks again!

@EUROSAFETYTRAINING Жыл бұрын

Send me your email to glen@eurosafety.us and I will send you documentation on Hydraulic system