EVERY Chevy Vortec Engine SENSOR

No video

EVERY Chevy Vortec Engine SENSOR

Рет қаралды 3,700

Күн бұрын

Every Chevy Vortec V8 truck engine sensor. How to diagnose and replace all Chevy truck engine sensors.
Chevy Silverado engine sensor replacement tips. Truck electronics repair tips. Bad engine electronic sensors.
Chevrolet Avalanche engine sensor locations. PARTS BELOW:
Parts:
Mass Air Flow: amzn.to/3zeA2Dr
Idle Air Control: amzn.to/4cz3Qcg
Throttle Position: amzn.to/4exMezd
Camshaft Position: amzn.to/4cz32DU
Crankshaft Position: amzn.to/3VVIuAn
Knock Sensors: amzn.to/3JjToZu
Knock Sensor Wiring Harness: amzn.to/3oMVzJ2
Oil Pressure Sensor: amzn.to/45ETyVE
Oil Level Sensor: amzn.to/3VSDk88
Coolant Temp Sensor: amzn.to/3XDKZs6
Coolant Reservoir: amzn.to/4cgDYBT
O2 Sensors (Upstream): amzn.to/4ezgQ3k
O2 Sensors (Downstream): amzn.to/45BnYb8
MAP Sensor: amzn.to/3VUWk5S
Always double check the part numbers depending on the years. Some of these
Chevy truck parts are different.
This is a 2002 Chevy Avalanche 5.3 Vortec V8 and a 2006 Chevy Silverado 1500 4.8 Vortec V8 engine.
Engine sensors for: 1999-2007 Chevy Silverado, Avalanche, Tahoe, Suburban, GMC Sierra, and Yukon Denali trucks.
Timestamps:
0:00 Intro
0:49 MAF Sensor
1:52 IAC Sensor
2:39 TPS Sensor
4:20 Camshaft Sensor
5:52 Crankshaft Sensor
7:37 Knock Sensors
9:32 O2 Sensors
11:46 Oil Pressure Sensor
12:52 Oil Level Sensor
13:01 Coolant Temperature Sensor
14:23 Coolant Level Sensor
15:03 MAP Sensor
16:16 Outro
**Disclaimer: Matt's Shop shall not be responsible or held liable for any property damage, injury, or financial loss, costs, or expenses that may occur from the purchase or use of the products featured in this video and or attempting to duplicate repair procedures. This is for entertainment purposes only. No warranties express or implied.**
As an Amazon Associate I earn from qualifying purchases.
#mechanic #customerstates #chevy #truck #silverado

Пікірлер: 67

@MattsShop Ай бұрын

These trucks have a lot of engine sensors! Mass Air Flow: amzn.to/3zeA2Dr Idle Air Control: amzn.to/4cz3Qcg Throttle Position: amzn.to/4exMezd Camshaft Position: amzn.to/4cz32DU Crankshaft Position: amzn.to/3VVIuAn Knock Sensors: amzn.to/3JjToZu Knock Sensor Wiring Harness: amzn.to/3oMVzJ2 Oil Pressure Sensor: amzn.to/45ETyVE Oil Level Sensor: amzn.to/3VSDk88 Coolant Temp Sensor: amzn.to/3XDKZs6 Coolant Reservoir: amzn.to/4cgDYBT O2 Sensors (Upstream): amzn.to/4ezgQ3k O2 Sensors (Downstream): amzn.to/45BnYb8 MAP Sensor: amzn.to/3VUWk5S As an Amazon Associate I earn from qualifying purchases.

@raylidell3613 Ай бұрын

Thanks Matt!! For folks trying to hold on to these older vehicles you are providing a valuable service to us all!!

@MattsShop Ай бұрын

You're welcome! Just trying to teach what I know!

@user-tb5vc4vm6l Ай бұрын

Thank you for all videos. I have 2002 Avalanche, 2003 Escalade, 2005 Yukon 2500 and 2008 Express. I replaced 3 oil pressure sensors on my 2008 Express for past 6 month. Fist sensor was from Amazon. Sensor start leaking oil throw electric plug after 4 month. It is easy to replace oil sending sensor on Express. It will be challenged to replace this sensor on Avalanche (2002 Avalanche required use a special socket). I replaced wit Dorman sensor from Amazon ( I think that was knockoff) . Sensor stop working after a couple month. I went to dealer, purchased overpriced sensor. GM sensor works good, no complains so fare.

@MattsShop Ай бұрын

You like the trucks more than me haha. Never use the cheap sensors. I did the same thing and now I'm going to have to replace it with the Delphi sensor.

@user-tb5vc4vm6l Ай бұрын

@@MattsShop GMT800- good trucks, affordable and easy to work on it. You need 2 jack stands, bottle jack and basic tools. and scanner. Only one problem- break lines. I had to replace lines on 2 Escalades. Newer donned this before. I replaced break lines on 1st Escalade. Its takes a 2 days. On the second Escalade - 1 day. Dorman makes a good stainless steel lines kit ($100-130). Thanks for your work.

@obsmotorsports9833 12 күн бұрын

Coming here from owning a 90k1500 Silverado. Recently bought a 03 6.0 Silverado to keep the miles off my 90 and now almost want to do the same to the 03 haha. Genuinely appreciate you and your videos to help me diagnose and find sny possible issues that may arise with my 03 and my dads 01 tahoe. Recently had a bad idle/stalling/sluggish takeoff issue so beforei found this video it ended up being just the MAF sensor, dirty air filter and dirty throttle body. Cleaned them up and runs absolutely amazing now. Will continue to follow up on your videos to these trucks to keep my in great shape❤️🤝🏼

@condor5635 17 күн бұрын

Excellent! 03 burb 285k. Never dealt with any except oil pressure and knock sensors. But awesome to know these others. Thank you!

@jesustorres-br4hr Ай бұрын

Can you do a video on getting out of anti theft mode

@d.jackson7023 Ай бұрын

Thanks! Your videos are always so informative!

@MattsShop Ай бұрын

You're welcome!

@DavidRamirez-bk3dy Ай бұрын

🙏🙏 very informative! I think we all needed these videos about these gmt800 trucks. I’ve watched all of them and subscribed 👍

@toronadogofast7868 Ай бұрын

Great job dude! Simple,informative,and to the point.

@MattsShop Ай бұрын

Appreciate it!

@Breenslg Ай бұрын

Thanks so much for these videos, dude. I have a 1500 and 2500 2004 sierra, and these videos are great help. I'm having electrical issues. Have you done a video of all the ground locations yet? Thanks again

@MattsShop Ай бұрын

You're welcome. Nope I'm doing that next: ground locations.

@longlivechina7538 Ай бұрын

You are my Hero

@MattsShop Ай бұрын

You're my hero!

@Buck_Boy Ай бұрын

I have a 2006 gmc sierra 1500. Thank you for everything

@MattsShop Ай бұрын

You're welcome! Basically the same truck!

@bartscave Ай бұрын

Thanks for sharing!

@MattsShop Ай бұрын

You bet!

@NickMango 9 күн бұрын

Damn dude, I wish I made this video lol. Freaking awesome nice job.

@SilveradoUSA1 Ай бұрын

This is an awesome video. How's about telling us what the readings for each sensor should be? 👍

@MattsShop Ай бұрын

That sounds like a good part 2 👍

@tcorley7477 Ай бұрын

Love the videos cause I have an 04 and 06 silverado

@MattsShop Ай бұрын

Awesome! Keep them runnin

@JesusGuerrero-fe3du 24 күн бұрын

These old trucks are way better than all the new 2021-2024 junk Chevy is bringing out

@BellaRocko Ай бұрын

Good stuff! But doesn't the Silverado have a transmission temp sensor? Thanks for sharing.

@MattsShop Ай бұрын

That's not an engine sensor. 🤣 It does but there is no gauge on the 1500's it's monitored by the computer and you get a light on the dash.

@jamessanders7408 Ай бұрын

Enjoy your videos Matt Does a 2006 silverado 5.3 have a PCV valve

@MattsShop Ай бұрын

Thanks, yes it does built into the drivers side valve cover.

@jamessanders7408 Ай бұрын

@@MattsShop I found out I have to replace the driver side valve cover because the pcv valve is built in Thanks Matt

@albertjohnson8108 Ай бұрын

Did you post this, take it down and repost? Please dont take down very valuable video!

@MattsShop Ай бұрын

I did, I forgot the knock sensors, so I added them and re-upload it. I'll never delete useful information 👍

@ZIGZAGBureauofInvestigation Ай бұрын

Could you list/cover [ common [mm] Bolt Sizes & its Torque specs ] such as, Thermostat bolts, oil pan, oil cooler gasket & oil drain plug bolts, water pump, etc components on 1999-2002 Chevy Silverado 1500 V8 5.3. Thanks MATT subbed as well v.

@kcemmanuel12savage75 15 күн бұрын

Subscribed! Thanks for the good content. I got a 2004 Escalade with the 6.0 Vortec. It takes a while to start in the morning, but then it’ll start up normally if I decide to start it up again right away. If I let it sit for a few hours, then it’ll take a few cranks for it to crank over. I seen this video you made and you mentioned the Cam Shaft Position sensor will make it take long to crank over. Thing is, I’m getting codes for, ‘P0651’ & ‘P0452’ It’s driving me crazy. Sometimes the codes clear themselves out on their own and come right back. & yes I know one is a 5 volt reference code, and the other code is a Evap code for the Fuel Tank Pressure Sensor. But I’m just wondering if It’s that simple as ohhh I need to replace the Fuel pressure sensor, & thats why possibly my truck is taking longer to start. I’m just wondering if that’s the right direction to look at. Basically what I’m saying is, would that sensor be causing that long cranking? Would love to hear your thoughts. Thanks! Oh,, & I checked the wiring harness around the engine bay, everything looked well protected, I know there’s a spot on the side where the battery is, that the harness runs over the head of the engine that is prone to damage, and that looked fine, it’s on a plastic clamp sitting nicely not touching the motor. Sooo idk 🤷‍♂️ Any thoughts helps Thanks!

@stat638 15 күн бұрын

Hey Matt I have an 00 v6 sierra. I’m having a slight hesitation at start up when pressing gas pedal it’s very sluggish until I get past 5 mph than it takes off. When I press gas it almost feels like a misfire or exhaust is clogged I can floor it and it won’t go at all till it goes past 5-10 mph. I’ve gone thru 2 fuel pumps in last 6 yrs. Replaced fuel filters and oil service done every 3k and spark plugs regularly done also any suggestions?

@tcorley7477 Ай бұрын

I have an issue with my 04 trans. Recently rebuilt, at low rpm in od it sometimes acts like it slips it'll downshift then shift up back forth back n forth

@MattsShop Ай бұрын

I would talk to the rebuilder. That doesn't sound right.

@UDRjames6334 Ай бұрын

Hey was wondering if you could help me with some information? I have a 07 Chevy Silverado and a lot of the fuses in the main fuse box under the hood is grounding to the motor some people say it supposed to and some people says it is not supposed to? So my question is any of the fuses supposed to ground in the main fuse box back to the motor?

@Dawg39 Ай бұрын

What scan tool do you recommend that has all live data option

@TunaFish1701 Ай бұрын

What size socket is the oil pressure senser?

@longlivechina7538 Ай бұрын

Its a special socket

@user-tb5vc4vm6l Ай бұрын

$15-25 in any auto parts stors.

@TheGaber2 Ай бұрын

Hello I have a massive problem with the cam shaft position sensor code p0342. I have already replaced it with the crankshaft and I still have a long crank start. I also ran the wire from the sensor directly pin to the computer and still same problem. Any idea on what it would be I what I could do?? Would be very much appreciated. Thanks!

@MattsShop Ай бұрын

I would look at the signal at the camshaft sensor with an oscilloscpe or at least a multimeter and make sure you have the voltage that's supposed to be there. You gotta get Delphi sensors.

@ghosteider705 Ай бұрын

Hey question I have a 2001 Chevy Silverado 2500HD that runs good cool but starts to want to die when it gets hot any ideas?

@Loading321 Ай бұрын

Hey matt, quick question I have a 02 Sierra and the rpm gauge stop working a couple days ago. Would you think this is a sensor or a cluster problem?

@michaelwest6181 Ай бұрын

Where’s MattsShop at?… I’m pullin up 😂 Your the sht bro 🫡

@MattsShop Ай бұрын

Haha thanks, I'm wherever you need me to be. 🫡

@CHEVYMATT19 Ай бұрын

Do you know what this means? I just replaced my mass airflow sensor cause I got a P0101 code on my truck so I replaced it and I still had the code. What do you think it could be 03 Silverado 1500 HD 6.0.

@BRED23 Ай бұрын

I’m having electrical issues with my cluster do you have any advice

@MattsShop Ай бұрын

Start with grounds!! There's a couple of fuses under the hood for the dash cluster. The dash clusters can have solder points that go bad.

@BRED23 Ай бұрын

@@MattsShop what ground straps should I buy would u have an Amazon link? Before I check out the hood static ground strap

@Eltakuachecuh Ай бұрын

Hey Matt, I have a question my 2006 gmc sierra at idle it gets stuck on 1000-1500 RPM until I hit the brakes and it calms down and then revs back up to 1000-1500 RPM. I’ve changed o2 sensors and nothing any ideas?

@MattsShop Ай бұрын

The first thing is to clean the throttle body and make sure it's not sticking. It could be a fuel related issue.

@Eltakuachecuh Ай бұрын

@@MattsShopThank you!

@bartscave Ай бұрын

I find that stalling issues on these are normally due to a dirty throttle plate.

@MattsShop Ай бұрын

Yes, that happens a lot too! The throttle gets sticky and it stalls.