1995, 1996, 1997 Kawasaki ZX-6R (ZX600F) Valve Clearance Inspection ZX6R

No video

1995, 1996, 1997 Kawasaki ZX-6R (ZX600F) Valve Clearance Inspection ZX6R

Рет қаралды 44,651

Күн бұрын

Hello everyone! Today we have a 1995 Kawasaki ZX-6R that I conducted a valve clearance inspection on. This information applies to the following years. 1995, 1996, and 1997.
Thank you for watching!
This video was Produced with CyberLink PowerDirector 17.

Пікірлер: 21

@tigerwoods5390 Жыл бұрын

Just bought a 96zx6 last week that needs carb service. Thank you for the work sir

@Struttin75 3 жыл бұрын

Awesome video, great job! How many miles did this bike have at the time of the valve check? Did you have to adjust any shims? Thanks!

@jarin12ga 3 жыл бұрын

This is a great video. I have 1995 ZX6R with 30k miles. Still runs awesome. Its smokes a little bit at first start, then goes away. This bike is a bitch to tune. Even from the factory the bike runs a little ratty from 1 to 4k. Then its smooths out and runs fine. But its a fine line between to adjusting the carbs, too rich or to lean. This motor loves being revved up after 10k. It comes to life like an F14. Im keeping it. She turns heads because of the age. People don't know what it is, at first glance!! Thanks for the video ,bro!

@OTRVM 3 жыл бұрын

Yes sir! Absolutely terrible below 4k but comes to life nicely.

@shaunparrish8714 10 ай бұрын

Hi fantastic video I’m currently just fitting new engine in mine could u please have a look at the rear of the fuel tap and tell me if number 1 runs to the right hand side of the fuel tank and number 2 to the left hand side of the tank I kno number 3 is to the pump

@fly1ngpapaya 4 жыл бұрын

this process is pretty close to the process on a 98 02 zx6r as well.

@OTRVM 4 жыл бұрын

Yes. I am about to be tearing down an 02 starting next week. One cylinder has only 60 psi.......

@yanthiago1977 5 жыл бұрын

Great job, it helped me a lot!

@OTRVM 5 жыл бұрын

Glad I could help.

@peterkwakman7440 4 жыл бұрын

The tail comes off exactly like a ZXR 750K1...I had a J1 conversion,paint job

@philhill7973 11 ай бұрын

That spring dropped down the intake with the valve open on mine ! Got it out eventually with a small magnet 🧲. Million to one shot to.

@OTRVM 11 ай бұрын

Oh no! Glad you got it. I have seen some that try to send it and fish out debris dropped and yeah....

@budsand_builds 2 жыл бұрын

Does anyone know where I can find that spring he took off the carb for the chokes?

@TheMisteraska 4 жыл бұрын

Thanks for the info, i am fixing a beatdown 95 zx6r i found for cheap and this helped a lot. Any chance you'll make a carburetor restoring and setting for this little beast?

@OTRVM 4 жыл бұрын

Thank you for checking out my video. I actually have a ton of footage regarding the carburetors. However, I have just not had any time to put it all together. So sadly I probably will not have anything in the near future up for this bike. I ended up swapping the motor on this bike as it had overheated at some point and the head was warped.

@sturflux2387 3 жыл бұрын

@@OTRVM how many km before ur motor is been dead ? Thanks