Expert tips. Program toyota hilux 2022 all keys lost smart key with autel IM608

Рет қаралды 7,226

Күн бұрын

Good day. In this video we will program a new key to a hilux 2022 smart key system, as all keys are lost. We will use the autel IM608 with APB112 simulater key, to get the ignition on, then we will program a new key. Enjoy.
You can also click on this bottom links to look, or buy the products I am using. I will add new ones later on.
#ad
to my equipment click link below.
#ad kd-x2 programmer
s.click.aliexp...
#ad vvdi mini key tool programmer
s.click.aliexp...
#ad Handy Baby 3
s.click.aliexp...
#ad Autel IM508
s.click.aliexp...
#ad vvdi 2 full
s.click.aliexp...
Autel im508 amzn.to/3F7NdFC
Autel im608 amzn.to/46HRqMh
Autel km100 amzn.to/3tj7wNL
Jmd handy baby 3amzn.to/3RO91Oq
Vag-k-Can amzn.to/3LQXsSv
keydiy KD-X2 amzn.to/3tqd2OU

Пікірлер: 16

@das5228 6 ай бұрын

dont need the code. enter immo data and back up eeprom than add a key. take the pcb out of shell and try different model. 4a transponder.

@CODING-FOR-YOU 6 ай бұрын

4A not on this model, it is A8 key. No need to disassemble pcb even in 4A models. Just backup eeprom then the machine can retrieve password from saved data.

@leonherbert9294 5 ай бұрын

Hi Buddy, So today I had access to the 2023 Toyota Hilux Legend. Used a Lishi to open the driver side door. Once the door opened the alarm was then activated but silenced after 1-2 minutes. I then connected my Autel 608 Pro2 and for some unexplained reason I was getting the error message "Cannot Establish Communication with ECU". I had the hazards lights ON and tried Auto Selection, Manual Selection > Immo Status Scan, Control Unit, & Hot functions with no success. Could not also auto detect VIN. The 608 was properly connected. One thing that I have noticed was that the battery icon showed 0.0 volts. I have checked battery voltage with a multimeter =12.9 volts. There's just no communication. Do you perhaps have an idea what my challenge could be. Thank you.

@CODING-FOR-YOU 5 ай бұрын

Good day. First check all the fuses. Sometimes the obd2 port fuse is blown or missing. Check on the obd2 port if you have power on pin 16. If there is no power, just connect a piece of wire from the battery to that point. Please be very sure it is pin 16. I have done this on a lot of vehicles, as sometimes the power might fail to a wiring problem or faulty connection. On any OBD2 port you should always have constant power on pin16. Hope this solves your problem. mechanics.stackexchange.com/questions/25257/disabling-obd2-interface-in-a-car

@user-ij9ek2pw2p 3 ай бұрын

Просто ваша машина находилась на штатной охране

@ricardogallardo5052 10 ай бұрын

Hello friend, this model is 2.8 AT SRV Euro 6?

@CODING-FOR-YOU 10 ай бұрын

Hello. It does not matter if it is the 2.4 or 2.8, manual or auto. The immo box works the same, but it is for europe models. If the key looks the same, it will program.

@troymash 10 ай бұрын

If I still have a key what tools do I need to program a new key

@CODING-FOR-YOU 10 ай бұрын

The OBDSTAR F101 will do the trick. It is capable to add or delete smart keys, but not all keys lost. This machine is only for toyota. s.click.aliexpress.com/e/_EwRq1Yr You can also use any main OBDSTAR machine.