📶ExpressLRS📶 Telemetry CALLOUTS Setup

📶ExpressLRS📶 Telemetry CALLOUTS Setup | EdgeTX or OpenTX

Рет қаралды 4,588

Күн бұрын

ELRS Signal Health: www.expresslrs.org/info/signa...
00:00 - Start
00:20 - ExpressLRS Signal Signal Health Wiki
00:59 - Transmitter Power Change Callout (TPWR Callout)
06:16 - Link Quality Callout (RQLY callout)
10:36 - OPTIONAL: RSSI and SNR Callout
Want to support me?
---------------------------------
Sign up to be a Patreon: / uavtech
Donate to my Paypal: spatzengr@yahoo.com
Use this Amazon Affiliate Link: amzn.to/36okaf7 to purchase ANY products [hobby gear, household items, etc.]. As an Amazon Associate, I earn from qualifying purchases.
Use this Race Day Quads link to make a purchase: www.racedayquads.com/?aff=51
Free Resources:
------------------------------------
Presets and Tuning Training Content: theuavtech.com
Facebook: / uavtech1
Betaflight BlackBox Log Review Group: / 291745494678694
UAV Tech Discord: discordapp.com/invite/rCCzgeT

Пікірлер: 38

@CapnBry 3 ай бұрын

This is a great explanation on how to set up these call outs and what values to use. EdgeTX / OpenTX use RQly for the "Signal low" call-out on the telemetry page, but I love your idea of having the value read. Someone should add a checkbox for that feature! The reason the RSSI doesn't go all the way down is usually due to the receiver's amplifier adding 12-15dBm, so -112 will drop off at -100 roughly.

@billmcdonald4335 3 ай бұрын

Some feedback: My setup is a TX12 with EdgeTX, a Happymodel 1-watt ELRS module with V3.3, and a HM Mob8 analog with an ELRS SPI receiver with V3.0. I'm running the ELRS dynamic power limit at 500mW. I set the TPWR callout interval to 50 mW; when set to 1mW, it gave me constant callouts. Most of my flying uses less than 100mW output, so I wanted Betty [my TX12] to pipe down and only tell me when I'm over that. EDIT: I added a logical switch that is set to ON when my throttle timer is more than 15 seconds. ANDing this logical switch to my TPWR and link quality logical switches makes it so I get an accurate countdown for landing without a callout stepping in.

@potepieniee 3 ай бұрын

@uav Tech from elrs site: OpenTX has no value for 50mW in the CRSF Telemetry protocol and instead will be read as 0mW. EdgeTX versions 2.5.0 and newer have the proper 50mW readout. Thanks for this video!

@josephvanbemmel7274 3 ай бұрын

Thanks for all your help! I don't fly a lot of long range but still like setting this up. Appreciate your time and all you do for the community.

@TechnicallyTom 3 ай бұрын

I seem to remember hearing about the 0 for 50mW issue awhile ago. Not sure but think it may have something to do with the CRSF protocol and that the TBS protocols don’t have 50mW so the CRSF protocol doesn’t support that value.

@billmcdonald4335 3 ай бұрын

Nice. Compared to my first 'real' TX unit, a 2-channel Cox-Sanwa from the late '70s, today's boxes do everything but make you a sammich. I got my AG01 Mini-equipped RM TX12 made into a proper Bitchin' Betty - and now I got 2 more callouts! Giddy-up. . .

@Chillin-fpv 3 ай бұрын

Awesome video. I understand so much more now. Thank you.

@skybug3 3 ай бұрын

Very useful detailed explanations! Now have my long range 3S powered quadcopter telling me every 10 seconds what the battery voltage is once it drops below 12v. Much more comforting than just playing a track telling me I have "Low Battery". Interesting to hear the voltage recover when I ease off on the throttle. Thank you!

@MCsCreations 3 ай бұрын

Really excellent tutorial, Mark! Thanks a bunch! 😃 Stay safe there with your family! 🖖😊

@ToddBurke42 3 ай бұрын

That was very helpful to see you go through the setup. Thank you!

@mlentsch 3 ай бұрын

I was just thinking about doing this - thanks!

@tubamanandy2 3 ай бұрын

Super useful video & really easy to setup - thank-you

@samavella8831 3 ай бұрын

Great video. Excellent explanation. Thank you😊 Would be interested in a video for TBS.

@BrainDeadEngineering 3 ай бұрын

Incredible!

@RubyS.1 3 ай бұрын

Very helpful. I fly FPV without an FC or osd

@uavtech 3 ай бұрын

and who is really looking at this stuff in the osd too while flying.

@Seii-FPV 3 ай бұрын

Hi Mark, another amazing tutorial. Thank you so much! So, basically your screen at 2:17, for say 5" quad, light HD freestyle mostly, do we need all those L05, L06, L07, L08 and L10 except maybe that L06 as you mentioned you'll probably get rid of it? I've set my L07 as 70% instead of 50%. Everything else should be as in that screen that shows up at 2:17 sec mark into your video? I use 250Hz (-108dB), so I've set my L05 as a

@jayzzz1234 3 ай бұрын

Any chance you can do a walk through of the modula 6 2024 set up?

@Mr_Meaty 3 ай бұрын

Great tips! I've got mine set to read out power levels at >51, because my dynamic power often goes from 25 to 50 to 100 with the rf noise around my house, but if it goes from 100 to 250 or 250 to 500 it reads it out to me. So maybe mine also reads 50 as 0 but I never hear it.

@uavtech 3 ай бұрын

Good stuff!

@Mupshot 3 ай бұрын

I run 250 always not sure why I would run any less. I suppose if I could go higher. It would always run higher. Buy an alarm on low db is something I should set up

@x8n1720 3 ай бұрын

Hello UAV Tech, thanks for your video. I already have done a similar setup on my Radiomaster Boxer with 1RSS

@DanoFPV 3 ай бұрын

Jumper T20 does not have any of these functions you are showing :), neither does my zorro.

@uavtech 3 ай бұрын

Discover Telemetry

@LicketySplitFPV 3 ай бұрын

I may have missed something. Do I need to have a quad plugged in? When I go to special functions after doing the logical switch, the TPWR option isn’t there. Sorry, new to ELRS, coming from CRSF where dynamic power was a no no.

@uavtech 3 ай бұрын

if your receiver powers up when you plug the FC into USB, you should be good. Clear and Discover Sensor again maybe. TPWR should also just be coming from the transmitter module.

@LicketySplitFPV 3 ай бұрын

⁠@@uavtechThat worked. And very cool! Stuck a quad in the washing machine and walked across the house. After 2 brick walls and the washing machine it started doing the callout. Gotta love elrs for working from in a “faraday cage”. Thank you for all you do!

@ivanmojica9924 3 ай бұрын

Is there a way to set it up on your OSD your mw power

@TechnicallyTom 3 ай бұрын

Yes. There is a transmit power OSD element in the latest versions of BetaFlight. On ExpressLRS though you need to make sure you are using wide channels if you want the value sent from the module to the receiver.

@ivanmojica9924 3 ай бұрын

I'm very new to E LRS I did activate it on my OSD but did not read I would love to get to work and what is wide channel sorry

@TechnicallyTom 3 ай бұрын

@@ivanmojica9924 ELRS has option for more efficient channels (hybrid). This limits some channels to only a few possible values. Wide channels support more possible values except on aux 1 that only does on/off values for arming. Go to the module settings on LUA script or module screen if available. There will be a channel mode option that can be set to wide.

@ivanmojica9924 3 ай бұрын

I'm so sorry for asking for help on this if you can help Can I contact you you contact me I am so new to this I'll give you my phone number if need be

@rgglenn150 3 ай бұрын

can you do one for crossfire?

@uavtech 3 ай бұрын

shpuld be the same. same protocol and RF tech. I would need to look. I assume it reports TPWR. I know it reports LQ.

@rgglenn150 3 ай бұрын

@@uavtech how about the thresholds? Also the same?

@comrat03 3 ай бұрын

OpenTX has no value for 50mW in the CRSF Telemetry protocol and instead will be read as 0mW. EdgeTX versions 2.5.0 and newer have the proper 50mW readout.