Fabricating Large Pipe Rollers

Рет қаралды 3,138

29 күн бұрын

In this video, we design, and Fabricate large pipe rollers. we use the shoppro burn table to burn our parts, and we use dual shield MIG to weld these ones up. Hope you guys enjoy, and thanks for watching!
#weld #welder #welding #weldshop #fabshop #fabrication #migwelding #shoplife #smallbusiness #millerwelder #freedom

Пікірлер: 40

@d3vildog 26 күн бұрын

I’m 52 years old and when the music starts boomin, I CRANK IT UP! 😎

@Freedomfabrication777 26 күн бұрын

Lol. Love the enthusiasm. The world needs more 52 year olds like you! Thanks for watching!

@natezimmerman3887 9 күн бұрын

Im really enjoying these videos. Currently transfering careers from a desk job to welding, so these have been very helpful and motivational. The quality has been awesome.

@Freedomfabrication777 9 күн бұрын

@@natezimmerman3887 Thanks, I’m glad to hear that. It always feels good to know that the videos have helped someone. Thank you for watching!

@PabloDeStefano-dk9mi 18 күн бұрын

Es un lujo todo lo que haces y un placer verte trabajar!!!

@Freedomfabrication777 17 күн бұрын

@@PabloDeStefano-dk9mi Thank you sir, that’s very nice of you to say. Thank you for watching!

@PabloDeStefano-dk9mi 16 күн бұрын

Gracias a usted por compartir todos sus trabajos!! Soy técnico en soldadura y lo saludo desde Argentina

@neilheriot2361 27 күн бұрын

👌

@Corey-dy2cq 27 күн бұрын

When I was in the Army I never met a person from Utah I didn't like. You guys got your stuff together! Another great video. Thank you.

@Freedomfabrication777 27 күн бұрын

Thanks, that’s really nice of you to say. I wish I could say the same. Lol. Thanks for watching!

@tallyman15 27 күн бұрын

Like the hoist. Work smart, not hard.

@Freedomfabrication777 27 күн бұрын

I don’t always succeed, but I try. Thanks for watching!

@JonesMetalCraft 26 күн бұрын

2.0 looks really good. Good call on the changes.

@Freedomfabrication777 26 күн бұрын

Thanks! And thank you for watching!

@michaelbigelow367 27 күн бұрын

I don't have a problem with the music but if I did I would just tune the volume down or off for that part of the video. Great job once again!

@Freedomfabrication777 27 күн бұрын

My thoughts exactly. Thanks for watching!

@jeffstanley2193 27 күн бұрын

Always good content!

@Freedomfabrication777 27 күн бұрын

Thanks, I appreciate that!

@jimcollins9316 27 күн бұрын

Great video Stuart. When you get the new press brake, maybe think about swapping the electric joystick for a manual valve, on the iron worker, it would be much easier to control. Also, a few months ago, you turned me on to Molly’s Silvers ’ belt buckles. I have 14 of them coming , 7 for grand kids and 7 for customers. I will send you a picture when I get them

@Freedomfabrication777 27 күн бұрын

I will have to look into what options I have for installing a manual valve. I would love to see the buckles! That is a really cool idea. Thanks for watching!

@MyLilMule 26 күн бұрын

Nice work, especially on the effort to continuously improve.

@Freedomfabrication777 26 күн бұрын

Thanks. Someone like me has to continually be trying to improve to get a decent finished product. Lol. Thanks for watching!

@McNeillWelding 27 күн бұрын

Nicely done

@Freedomfabrication777 27 күн бұрын

Thanks!

@paulusmarc 27 күн бұрын

Bon Boulo 😆😆👍👍

@garryfuller2079 27 күн бұрын

Hey I like this video. We have a shop in southern Nevada. And we are always trying to make things easier for us while fabricating. We usually mKe one then change it up a little on the next. But we always run into the question , should we just make another one so the whole lot matches or give them the one that is slightly different. Just curious to how you handled that situation with your first one you made compared to the other ones you made slightly different. Thanks again for the content. And god bless!

@Freedomfabrication777 27 күн бұрын

Sounds like you guys have a sweet setup as well. I had the same thoughts on the one that was different. Lucky for me, the customer stopped by and checked out the first one when I got it done, and said he loved it. I brought up my concerns, and he said he thought it was great the way it was. I told him I was going to modify a few things to make it better, and he said that would be fine, so I just decided to give them the “prototype”. Situations like that are tuff. I dealt with it the best way I knew how. Great question, and thanks for watching!

@HVACQualityAssurance 27 күн бұрын

Installing bearings can be easy or hard, depending how patient you are. I *ALWAYS* took my time, and got them on, w/o jacking anything up. Having to do a job under warranty is *NOT* good for the resume😉

@Freedomfabrication777 27 күн бұрын

That is the truth! It’s hard to make money when you’re fixing warranty work. Thanks for watching!

@bsg2580 27 күн бұрын

Always fun to watch. Thanks for another great video! If you make another box like that, try burning some slots to show you where to brake those corners- a little layout on the computer should speed you up at the brake. I’ll bet you could make the slots at the corners long enough so you could bend the corners by hand, and only have one corner to weld.

@Freedomfabrication777 27 күн бұрын

I’ll have to give it a try. Thanks for the suggestion, and thanks for watching!

@Posibrian 27 күн бұрын

Looks like those pillow block bearings have zerk fittings? I always clean my shaft like you did and also put a thin film of oil or grease on the shaft before installation, I like version 2.0 better for what it’s worth besides the shaft protruding out more on one side. Love the layout of the shop by the way!

@Freedomfabrication777 27 күн бұрын

Agreed. Version 2.0 is much better. Thanks for watching!

@billyword7428 26 күн бұрын

I would like to know how you came up the angles for the stand. The equation

@Freedomfabrication777 26 күн бұрын

I actually didn’t use an equation. I’m not that smart. I drafted a side view on my CNC software and tweaked it until I like the angle and the footprint. Definitely no rocket science going on here. Lol. Thanks for watching!

@joefalmo5528 27 күн бұрын

i could really do without the music. I'm 61 years old and as soon as it starts booming, i turn the video off

@Freedomfabrication777 27 күн бұрын

Darn it.

@lepatriotequebecois 27 күн бұрын

good video but music is little gay plz put old rock music🤘🏻

@Freedomfabrication777 27 күн бұрын

When you have a KZfaq channel, you don’t get to slap whatever music you want on there due to copyright laws. The options are quite limited, Thanks for the blunt suggestion though.

@lepatriotequebecois 26 күн бұрын

oh ok I didn't know sorry man have nice day I can't wait to see your next project🤘🏻