“We’re welding a fucking dumpster…” no truer words ever spoken. People get SO worked up about weld quality and perfection… no matter how good you weld that, you’ll probably be out there next week fixing it again anyway lol. These guys at these scrap yards are fucking brutal on equipment.

Your descaler peens the surface so under each little impact metal gets compressed and expands a little. Remember what the head of your cold chisel looks like. All these little expanded areas push against each other so you have a thin outer layer in compression on the peened surface. Since failure cracks can result from tension in that outer layer, the compression stress negates a bit of the tension stress and the parts act stronger. Peening under controlled procedures is common aircraft practice. I enjoy your videos.

Look forward to the video of fixing the magnet bracket. Will be really interesting!

Appearance is gold I don't weld with my finger nor cheater the customer deserves better,

4:10 peening will work harden that lever, but slow cooling after heat & bend will return that part to it's original properties. It's likely a low carbon steel, so very few options for hardening.

Just a handy tip when you want the c- channel to come down use a 6inch c clamp with 2.5 inches cut off or half with a heavy duty base plate and clamp it down in place it comes in handy even in small repairs it's a life saver

As always the content is absolutely golden. I’m just getting started in my welding career but I’m hoping to be doing this type of work some day soon.

So good to see all these different projects. Learn a ton every time.

Great video. Thanks for including details - very educational. I always learn something practical from your videos.

The cracks on the magnet look like a design change would help. Change the angle of the bars so they are not so flat. No doubt torch cutting the holes didn't help but looks to me like they need a little more meat on the bottom if room allows it.

Good job. Informative. Especially when you talked about cracks developing from torch cut holes. Keep it up.

We’re welding a dumpster this isn’t a fucking space shuttle 😂😂😂. Love it.

I run a little welding truck and I too weld On just about everything….. These people’s comments are entertaining…. I didn’t realize there are so many keyboard/ welding experts!!!! GOOD LOOKIN SOLID WORK👍👍👍👍

Nice work Anthony! When you welded the backside of that angle/ channel I was thinking how throughly was your work even on a dumpster! Probably stronger now than from the factory. Great Video!

Places like that are the bread and butter of the job. Nice work as always

I really enjoyed this longer video Andrew !

That was a slick move keeping the arc from tack to tack on that can..

Another great video Anthony!!

Your a one man army Love it bro Keep it up 💪

One of my first welding jobs was at a scrap yard like this one repairing the bins and the escavators.

Bro I've been doing repair work for quite awhile sixty plus years and believe me i have learned alot from your videos just goes to show you that your never to old to learn some things.keep up the good work

Great video, very interesting. Looking forward to the repair video on the electro magnet.

Need to get you a dog and a wedge for that, we’ve used them a ton and man do they ever work good! Good content as always!

From one business owner to the next. I'm planning a trip to Florida in August for vacation. Wouldn't mind if you didn't to tag along a job or two. Free labor and yea I love work so much couldnt think of anything else better to do with my vacation time. 😆 🤣 😂 Keep up the hard work you continue to be a inspiration to others.

Fantastic video all ways look forward to seeing them. What a days job those cracks are made to think that could of completely broke. Hope you get to make a new 1 and can film it. Keep up the great work 👍👍

Hey Mel, just hooked in to your videos. Great talk through, nice commentary. Smart move, pushing that mag repair, just like in the China shop, “You touch it, You own it”, in other words if it breaks after your repair, they’re coming to see you. Hood down lights on.

It would take a while but you could mag drill bigger holes and press a sleeve into the steel the right size for the pins. I know it’s still a heat affected zone but I think that would probably be a decent cheaper option. You could even just press a sleeve and weld it and grind it smooth and I think that would do fine as well. Because once you press the sleeve in and welded it you could air arc those cracks out and full pen weld them using the sleeve as the start of your root pass.

I'm new to your channel and it looks like you have a wealth of support . Very interesting looking forward to watching.

Watching that bead from the front while you worked the back was killa, the red glow cruising along

Looks like your making good use of that new air compressor…why not?? Another tool in the arsenal!!! Keep stacking my guy!!!

Nice stick welds! Really nice beads!:)-John in Texas

Another great welding vid. Right on

"this is dumpster, this isn't the space shuttle", nice line.

Did you consider drilling larger holes and then welding inserts in? Seems like that is the most cost effective solution to me.

I use a needle scaler to peen welds in cast to compress weld and prevent cracks.

Get you some short pieces of 1x1/2” and 1-1/2x1/2” channel iron to lay on round stock when trying to C-clamp it. Helps quite a bit.

Great work man! For the glare problem you were having, I just self tapped a big square piece of canvas on the top of my hood to run down the back of my head and neck. You can just cut up an old welding shirt.

Great video Anthony mate! Jealous of the weather you're working in! Peace from shitty England 🇬🇧 🇺🇸

You da man I’m definitely looking forward to seeing that magnet fix as well hell ya Wooooooo

Dude I used to work for that company that made that magnet pretty neat seeing it in a video

You need one of those hydraulic kits that has a hand pump, there kind of fast in some cases have a few adaptors for length or wedges and plates for pulling or pushing - toys in the toy box.

From what I'm looking at just cut them loose flip them over and drill the hole in the other end as well into the inside center and weld up the holes and welded back together and use your expensive mag drill

Great work as always. You should pickup a Miller or Lincoln “face mask” and keep it on your truck. They are invaluable for work outside. Not only do you have no backlight (since they are goggles) but you can get your head in places/better visibility than a normal hood.

Dang was looking forward to that project. Oh well next video should be nice as always

Cool video Anthony

On that little dumpster , for the crack that would not close .. i used to be a structural iron worker , connector , and we used to carry some big J adjustable Clamps and we would cut off the bottom piece that acts as a plate to grasp what ever your trying to hold and we would weld the j clamp down that allowed us to have direct over head pressure to push down on a pc and not have it twist

Great video;)

dear GOD man!! can none of ur 1000 sponsors throw you a pancake hood?! today woulda been the proper day🤙🏽

Nice job man. Time for a remote, they really save trips back and forth to the welder. Especially jumping back and forth from 6010 to 7018 or different sized rods etc.. I know you know that but just tossing it out there. ;) I've been running my Crosslink remote for about a year now....don't know I got along without it.

With the channel bent up on that Can, you think you would’ve been able to tack up a plate on the can itself and use it as a base to use a bottle Jack to push that channel back down? Genuinely curious always trying to learn! Love the videos man!

Been there. Relief cut then pull down and fill in on the C channel.

gota love those needle guns.

I'm surprised to see you not weld around the edges on the first weld you did where you were selling a pieces of metal flat to another. In my experience that going to hold water inbetween those two pieces causing it to rust and rot much quicker. If I do a weld like that I always weld around sealing the inside where it's sandwiched together

Need to hook your self up with one of those Pipe Liner Pancake Hoods, form what I understand they designed to Eliminate that Back Light/Glare with that kinda Ski-Mask Goggle Setup. As we'll as being Compact and Light Weight. Would be a handy dandy accessories to have in the Tool Arsenal ?

You need to invest in a pancake welding Helmet ... You will find out it's heaven when dealing keeping sun out...

Look into getting a pancake hood. It eliminates glare. Pipeliners use them for that reason.

Love the content dude! Keep up the awesome work! How do you like the Hobart helmet?

On the magnet - all you had to do was cut them off and reverse them then mag-drill the holes. Welding up the cracks would be good but they would bend close. Just my 2 cents

Why not use some screw dogs or grasshoppers to pull/push stuff back into place? Like when you trying to get the "F"/ bessy clamp on it. A c clamp cut in 2 or simple a couple long bolts,"L" plate and couple nuts to make a nice screw dog or grasshopper would've worked good. Just an idea

Did you ever end up getting to fix that in the end? That would have been or would dope too watch you fabricate that.

Only thing I would suggest on cracks is drilling out the ends of them because it stops the crack

Im just curious, how in the hell did you aquire your cert of completion to be a Jman welder

can't wait till you get back on the magnet.....cheers

Soon as I seen them cracks my brain went Cha-Ching $$$ lol

Have you tried a pancake shield Anthony? Dose good to eliminate sun glare.

you gotta be drilling holes at the end of the cracks it stops the crack from becoming bigger, it basically routes the crack back to itself.

How are you liking gouging on your machine? I’ve got a 325 trailblazer and would like to gouge but don’t want to over do it with the machine

The cracks actually look like starter cuts for the holes

The Magnets I have seen here in California have chain instead of a bracket that can crack.

If they don’t wanna remake the arms, will you be welding it up to get them going again?

Yes thats a good days work

This isnt the space shuttle, how true!

man, if i had to do those repair id ask for the fork lift so i could lift those containers and work standing XD

If ridges are not too deep they can be smoothed out with an end grinder.

You could try s dog and a wedge or screw dog to pull that C channel down basically a dog is just a piece of steel like plate any thickness with a notch cut out of it for your wedge you weld the 1 side down and smack your wedge in between the notch and C channel

I would almost second guess those even being cracks. Id bet its the entry wound from the torch. See it everywhere on new, cnc cut thick material

"Today on episode 1 of Weldin' Wyatt's Winkle..."

MM77 Approved 👍🏼👍🏼

Mud dobbing lmao 🤣

Are you still moving to Montana?

How did you terminate the crack on the dumpster at 5:00? Or did you?

Should just flip that crack towards inside and weld the cracked hole on the magnet project just to save money 👍

Grab a port-a-power kit they make decent cheap sets

When welding on multiple pieces of equipment at the same place do you charge by the hour or a minimum per piece of equipment

Clever way to bend the latch back

Did you go back to fix that magnet?

We use chain on our magnet

How are you pricing jobs? Time, scale, piece work?

What kind of scrap yard is this? As soon as you said "buy some metal" they should have said "Hell, we got mountains of the stuff. I'll have some guys scrounge you up something." I get it strictly speaking it is better to use new, store bought metal with a pedigree other than mystery meat bastard metal. There is a big scrap yard (sorry Metal Recycling Center) in my town and it seems the whole place is held together with mystery meat bastard metal. BTW I just found your channel and I love it. Thumbed up, subscribbled and all that stuff in the dibbly do. Guys like you burning rods, heating with torches and beating with hammers keep industry going. I also respect the hell out of scrap yard workers. They do more for the environment than Prius drivers.

lol why arent they using the D-rings and chains that the magnets usually come with?

Well. I learned thst you shouldn’t torch cut a hole like that in a structure piece thst is gonna be a long term use piece. Good to know. I also wonder if because of the torch cut, the location of the crack is showing on the bottom ones of the hole, with the least amount of structural metal leftover, ultimately failed from stress and over use.🧐

Needle scaler new addition to the toolset or do you rarely use it?

don't let em fool ya those scrap metal guys are loaded fix it right👊👍

Get a pancake hood. Definitely will help with the sun on your back coming in

I’m not a welder lol but I do have experience lol

You can torch cut it 100% I do it only buildings, you just need to clean it up so there is no tear points

Just make a new lift point for the magnet lol that thing looks dangerous

You could have cut the existing flat bar off drilled new holes in the opposite end, a bit of a clean up and weld it back on. You could have also mag drilled a bigger hole and put a steel bushing in it. Plenty of fixes on the cheap for old mate in this scenario.

Could you flip bars over an then drill

Space shuttle..... It's not Rocket Surgery !