#inverter #TP4056 #charging #awesometech #diy #diyhacks #diycrafts #tp4056 #quantum_tech #fake #diyfakehacks Genuine video link : kzfaq.info/get/bejne/o5-Gg7p2mcqnpqs.html
Пікірлер: 32
@BertoldVdb8 ай бұрын
Connecting a bipolar transistor to the output can certainly increase the current, but the max charge voltage will become slightly lower (Vbe drop). You connected the mosfet wrong, it will just pass the input voltage to the output.
@gregjones36609 ай бұрын
You could just solder that wire from the + of the input to the + of the output. no need for the transistor and additional circuitry. The mod will also be 5.15V where the current is limited by the power supply you chose.
@riepriatna80411 күн бұрын
wrong resistor, it should be 1 ohm not 1 k, and this method is a current (A) boost, not a voltage (V) boost
@WalllOfNothing Жыл бұрын
Why is the red probe(Positive probe) is connect to negative output?You put the red probe in the negative in your multimeter or what?
@leopoldofernandezjr.508 Жыл бұрын
I watched this on another KZfaq channel. Now i know it's Fake. But you must try first to remove our doubts regarding the project.
@Sams-Fy9 ай бұрын
It's the current (Amps) that increases, not the Voltage....
@fu1r4 Жыл бұрын
It is the current that will get higher and not the voltage ... Connect a cell and use a clamp ammeter to measure amp
@Imbaloogs6 ай бұрын
Wrong way of testing... you are checking the voltage and not the current.
@albarbro6 ай бұрын
i just replace the resistor using Zener Diode with 2pcs IRF9540 + 1pcs TP4056 + 5V 40A power supply to charging 4pcs 18650 = 7A MAX
@MiuiThemeIzanАй бұрын
Forma incorrecta de realizar la prueba... estás comprobando el voltaje y no la corriente.
@qanikadriu72329 ай бұрын
Mos besoni këto gënjeshtra të mëdha,mos humbni kohën kot me këto gjëra.
@mr.rishideshmukh20612 жыл бұрын
NYC
@user-tz3qv9kz6r9 ай бұрын
Does the charger not get hotter ?
@QuantumTechpakistan9 ай бұрын
No, using 5v 20a supply
@fu1r4 Жыл бұрын
👎 because you still have the protection film on your multi meter ...
@wahid6497 Жыл бұрын
just connect a battery or load then you will see the voltage will no go over 4.2 volts multimeter/voltmeter is not load
@wahid6497 Жыл бұрын
and if you are curius just put diode in series
@QuantumTechpakistan Жыл бұрын
brother you have to understand that lithuim ion cell needs constant voltage if we charge those lithuim ion cell with non constant voltage cells life decreases accordingly
@QuantumTechpakistan Жыл бұрын
encrypted-tbn0.gstatic.com/images?q=tbn:ANd9GcRbHK6OGTHo9I2wJOZCshE996-cQcgxwtpvjg&usqp=CAU Please understand this chart Link above
@wahid6497 Жыл бұрын
@@QuantumTechpakistan thank for the information but maybe see the voltage measurement while charging a battery cause you did just without connecting any battery i don't have the MOSFET on hand
@wahid6497 Жыл бұрын
If there is constant voltage
@ahsanhabibnafi23882 жыл бұрын
Whats that rasistor?
@QuantumTechpakistan2 жыл бұрын
1k
@ahsanhabibnafi23882 жыл бұрын
@@QuantumTechpakistan is that 1k or 1k ohm
@QuantumTechpakistan2 жыл бұрын
@@ahsanhabibnafi2388 1k ohms
@sujangiri350 Жыл бұрын
@@ahsanhabibnafi2388 both are same bro 1k is the value and ohms is the unit