Yes vacuumcleaner connected to the dipstick hole helps.
@AndyFromm9 ай бұрын
I did that on the next filter change 👍
@ihus9950 Жыл бұрын
Looks to me Andy you take great care in your equipment, keep up the great work Bud👍🏻
@AndyFromm Жыл бұрын
I try, thanks 👍
@claesmansson90704 жыл бұрын
I usually have some gasket sheet material,so can make own g.Working on 826,did mcv g.s and cover under there when cleaned up inside where trans.break goes inside.Found 2 nuts with broken parts of bolts,so have to find from where before start second time in 35 years.1.time started right away (30 seconds,a week ago).G.b.
@dansherrell68032 жыл бұрын
Why didn’t my 756 do that when I took the filter cover off? Only lost about a gallon.
@AndyFromm2 жыл бұрын
Maybe your dipstick seals up tight? I know I could hear mine pulling air in. It probably should vent some for when it warms and cools so it doesn't build excess pressure & blow a seal. I can't really say for sure.
@dansherrell68032 жыл бұрын
Gotcha. Idk what’s up with the tractor now but the reason I had that cover off was to fix the gasket because it was pissing hytran on the ground and ever since that it won’t stay primed, oil light is on and have no steering until I drove it a bit and work the steering wheel a while. I took the plug out of the MCV to bleed it and that works immediately but after it sits again for a while I have the same issue. I don’t think it’s a pump issue, I think it’s air but I don’t know how it’s getting in.
@AndyFromm2 жыл бұрын
@@dansherrell6803 so I changed my mcv pump out but that only fixed it so it self primes and doesn't loose prime while using it(hills). I still loose prime when it sits. I think is what is causing it, my brake valve weeps. That probably allows some air to get into the mcv system. Basically the way I understand it, any weep point can also let air back in. I have been to busy to look into it more and it "works" now.
@dansherrell68032 жыл бұрын
@@AndyFromm aha!!! I have a weep at the brake line where it supplies fluid to the brakes and it’s leaking a little from where the left side 3pt arm mounts to the frame behind the axle housing. Thank you!
@AndyFromm2 жыл бұрын
@@dansherrell6803 the leak near the 3pt probably isn't the issue if its where I'm thinking. Basically anything leaking/weeping on the brake, steering, ta, and/or mcv could allow the mcv to bleed off. Some guys hook a line from the hydraulic coupler to the bleed port on the mcv and just charge it each start up. Good luck 👍
@robertkeller69852 жыл бұрын
Did you drain all the oil out or did you just send it
@AndyFromm2 жыл бұрын
Full sent it, next time I'd like to put a vaccum on the fill hole or atleast a boat plug. I'm guessing if I didn't have the dipstick in at all this would have been bad.
@r.hazelwood48854 жыл бұрын
We had a 7000 and 7080.. the 7000 was a great tractor (haying and plowing).. but the 7080 was a dog... Fuel hog.. overall the engine once or maybe twice.. I would have another ac 7000 again.
@kenthawkins24184 жыл бұрын
👍IH!!!!
@AndyFromm4 жыл бұрын
hello kent
@r.hazelwood48854 жыл бұрын
Now... Now if you want to get rid of your 806... Lot me know!!
@AndyFromm4 жыл бұрын
Will do but so you know, i don't get rid of anything 😁