Fastest dovetails East of the Mississippi
Рет қаралды 38,870
9 ай бұрынI needed to dovetail some drawers. But I wanted to try something new. So instead of breaking out the handsaw, I broke out the bandsaw.
And thank you to Henry's House of Coffee and Tarpley Studios for their kindness and general awesomeness. You can support them at:
henryshouseofcoffee.com/
www.etsy.com/shop/TarpleyStud...
Thanks for watching! If you enjoyed this video please consider supporting my channel by subscribing and hitting that notification bell. It really helps small channels like mine.
---------------------------------------------------------------------------------------
Items I use in this video (some are affiliate links which help sponsor this content):
Sandpaper: amzn.to/44NCPx7
Spray Adhesive: amzn.to/3PviJTW
Double Stick Tape: amzn.to/3RjlY26
My favorite trim router: amzn.to/3LbCbTF
DeWalt Trim Router fence: amzn.to/43cYwr2
1/4" Spiral Upcut Bit: amzn.to/461b2KJ
----------------------------------------------------------
Items I keep on hand in the shop:
Glue:
Titebond I Wood Glue: amzn.to/3zRXHGv
Titebond III Wood Glue: amzn.to/3MVnG6j
Titebond Quick and Thick: amzn.to/42HGuMC
Liquid Hide Glue: amzn.to/3PhZEEW
Power Tools and Accessories:
Table Saw Blade - Woodworkers II: amzn.to/42bIOLa
My favorite trim router: amzn.to/3LbCbTF
DeWalt Trim Router fence: amzn.to/43cYwr2
My Festool Router Setup: amzn.to/3ZPIQal
Extra Fence: amzn.to/3KHi9jI
1/2" dia Router bit: amzn.to/3UkRFYI
A Better Alternative (Spiral Up Cut): amzn.to/3mcPsSp
Sharpening:
Ohishi Waterstones: amzn.to/3TkoZhP
1,000/8,000 Combo (great budget option): amzn.to/3Lqj7Sh
Angle Setting Jig Plans: www.lie-nielsen.com/pages/dow...
Inexpensive Honing Guide: amzn.to/3Jo2Uub
Lie-Nieslen Honing Guide: www.lie-nielsen.com/nodes/423... guide
Sandpaper for Flattening: amzn.to/3Jor73F
My Finish Mix:
Minwax Polyurethane: amzn.to/3kPgpuO
Liberon Finishing Oil: amzn.to/3kXkIEf
Danish Oil (alternative): amzn.to/3Njlabs
Liberon Beeswax: amzn.to/3Jm2yFN
Turpentine: amzn.to/3SWFznB
Mineral Spirits (alternative): amzn.to/3oKU83h
TotalBoat Epoxy:
For 5% off any TotalBoat product, visit www.totalboat.com/encurtis
You can stay up to date with my work here:
/ encurtis
/ encurtis
encurtis.com/
@tommoeller7149 9 ай бұрын
" Go make a thing and have some fun doing it." About the single best piece of advice I've heard in a year. Thanks!
@ENCurtis 9 ай бұрын
😎🤘
@foppkn4867 3 ай бұрын
I am a disabled and seriously depressed person who enjoys woodworking. I'm from Australia and I just want to drop my thoughts into your comments section, for all to see how you affect real people who watch your channel.....I itch for each new chapter you make. I don't mean to sound creepy but...... "YOU INSPIRE ME TO BECOME BETTER, you encourage me to "Make a thing" The way you present things in the no bullshit way makes it real. Thank you for being real, from the bottom of my heart FOPPKN. Enjoy your whiskey, I know I do. Cheers
@fallen2189 9 ай бұрын
Your skill and demeanor warrant way more subscribers than you currently have. I'm 72 years old and have been a professional woodworker for 52 years and I thoroughly enjoy your presentations!
@skippylippy547 9 ай бұрын
yes! 👍
@ENCurtis 9 ай бұрын
Thank you so much 🙂
@alanwilliamson2259 4 ай бұрын
I like the videos... you just show it the way it works for you... which makes it easier for us plodders. Thankyou.
@robohippy 9 ай бұрын
When chiseling out end grain, a trick I learned from some Japanese master video I watched, get the end grain wet, then pare it off. I use a pipe cleaner folded over 4 times. I was/am attempting to do this with some very dry American Chestnut, and was getting horrible tear out, well maybe chunk out. The water trick fixed that. No need to have 17 degree bevel chisels....
@michaelbauer7023 9 ай бұрын
Semi-old carpenter here... I can "construct" almost anything and always thought I could make furniture. However, I never had the proper tools to make it happen and therefore never attempted to do so. I then retired early and built a wood shop in my garage... all and all I am proud of what I have built so far, but I have not yet ventured into dovetails because it's intimidating and had/have so many other things to learn (i.e.: proper material prep, consistency, precise accuracy, etc). Going from a carpenter's pencil and circular saw to a marking knife and table saw was a step within itself. This method (power tools) makes the task of dovetails less intimidating. Because of this video, I will soon try dovetails with power tools to learn the functional basics without the intimidation of using all hand tools... and then one rainy day I will attempt "old school" and try 100% hand cut. Thanks for the instructional content. Please keep it up!
@ENCurtis 9 ай бұрын
Really glad to hear what you're taking away from this video. Thank you for sharing that. And good luck my dude!
@frankschoenle8566 6 ай бұрын
It’s just plain fun listening to you.
@danielmathews-kj6ov 2 ай бұрын
I have stopped watching NETFLIX… you are awesome! Instructive, authentic, entertaining as hell!!! Keep ‘em coming. Dan in Hawaii
@jameslockwood5113 9 ай бұрын
Educational, entertaining, cathartic, truth. Tks
@BillMSmith 9 ай бұрын
Totally legit. No one cares about the shape of the wood waste. (Except uncle Charlie, and you know how he is.) Good call on dovetailing Vs pins on the drawers. This is where you're doing a great job getting us all to think about how the details work together.
@ENCurtis 9 ай бұрын
Thank you 🙏
@elmaestro35 9 ай бұрын
I’m 💀with the title. Love it. And I enjoy watching your videos, so chill and awesome as well inspirational.
@tedwards7404 9 ай бұрын
I am a little old lady getting ready to retire and make a bunch of sawdust in my shop. I started woodworking with my dad as a small child but haven't really done any serious builds until recently. I love your channel!!! You have a kind way of presenting your expertise and it is always understandable. I truly appreciate you! I hope I can make some beautiful pieces to pass on to my grandchildren so they can remember how much i love them. You are helping me to make that happen!! Keep up the good work young man!!
@ENCurtis 9 ай бұрын
Thank you so much! I love to hear that. I’m sure you’ll make some lovely objects if you keep after it 🙂
@philaandrew100 9 ай бұрын
The good ole Bandosaurus technique. It's a crowd pleaser for sure.
@ENCurtis 9 ай бұрын
😂😂
@briancollins2230 9 ай бұрын
Always entertaining, always educational. Always a great way to get my dovetail out the chair and in to my shop. Thank you.
@ENCurtis 9 ай бұрын
Thanks!
@davidmeyer9204 9 ай бұрын
Thank You Eric! I like the router and bandsaw idea for hogging out material, thanks for that.
@ENCurtis 9 ай бұрын
Thanks David 👊
@214rwoz 9 ай бұрын
1 in 7 is my go to, the book in the back ground has been in my shop for many many years, I think it needs another look, thank you for all your time and effort.
@NPOAfterMidnight-ft9zj 9 ай бұрын
I learn something new every single time u put up a video. Thanks!
@ENCurtis 9 ай бұрын
I’m really glad to hear that!
@chipsterb4946 9 ай бұрын
Your approach to jigs is so refreshing! I recently spent hours making a crosscut sled after watching who knows how many videos on how to make “the ultimate crosscut sled.” Then I saw a Norm Abram jig to do the same job. 🤪 It was a runner, a base, and a “fence” aka a strip of wood. And it worked. P.S. I did learn from a plethora of mistakes on my sled so it wasn’t time wasted.
@jorgfellinger8004 9 ай бұрын
Pure amusement for wooddies!
@torque8899 9 ай бұрын
Literally cut my dovetail tails yesterday an wanting to cut the mortis of the half blind ends Monday and was thinking ‘shame he’s not got a video on this as I’ll bet he has an easy solution’ an boom the universe heard me 😂 thank you man! Really useful
@ENCurtis 9 ай бұрын
Haha glad the timing was just right for you!
@simonhayter5984 9 ай бұрын
Interesting, yes. Entertaining, yes. You're the best Curtis 👍.
@ENCurtis 9 ай бұрын
Thank you!
@darodes 9 ай бұрын
Always hyped for a new video!!
@ENCurtis 9 ай бұрын
Thank you!
@paulruud5804 9 ай бұрын
I am sure Michael Fortune is applauding somewhere. Or he would be if he saw this video. I'm applauding.
@kennethholmes9315 9 ай бұрын
I do a lot of inlay bow ties on the bandsaw and then hog out the piece with the same router in a plunge base. I have to admit there nice. Have a good one.
@robynbazlen-weglarz7836 9 ай бұрын
You are always educational and fun. Thanks!
@ENCurtis 9 ай бұрын
Thank you!
@thomasweller1321 9 ай бұрын
I think it's your passion for making things as well as your original feelings towards your work as well which draws we "watchers" in. Thanks again. And, as I've said before, keep on making it for the enjoyment of making things. As a former teacher, I can relate.
@ENCurtis 9 ай бұрын
Thank you so much, Thomas. I really appreciate that.
@AusWorkshop 9 ай бұрын
I agree, it drawers me in too 😊
@user-bf9nv7ld7q 9 ай бұрын
The explanation of the angles you use was really enlightening. I have never seen anyone explain how and why they cut their dovetails a certain way.
@johnritchie3889 9 ай бұрын
If all my jigs were fancy, I wouldn’t have room in my shop for tools. Make a quick jig from scrap and burn it when you’re finished with it.
@johnjoyce5441 9 ай бұрын
Great work. Hand tools or power tools is always a question. My old high school wood shop teach would never let us use a power tool until we showed that we could do the work with hand tools. That’s how I am teaching my son.
@KOutOfMyYard 9 ай бұрын
Sunday morning. Coffee in hand. Great way to start the day seeing you do your thing. And I will tell you that it is consistent, considerate and educational all while being just plan great to watch. I hope that you enjoy doing what you are doing bc it sure does show through that you do. Keep it up
@ENCurtis 9 ай бұрын
Thank you so much 🙂
@ronlonsbury8893 9 ай бұрын
love your videos. You have an excellent teaching style.
@ENCurtis 9 ай бұрын
Thank you very much!
@Cstandri33 8 ай бұрын
Just wanted to say I’m a huge fan and just starting my business I appreciate you very much
@davidcchambers 9 ай бұрын
Takeaways in no particular order... Expanding skills cutting dovetails on the bandsaw; Down and dirty jigs to get the job done (not a takeaway, but I appreciate reinforcement, I don't enjoy jigging either); Good coffee in a hand-made mug, gifted from the heart; Waxing the base of jigs for a smooooth ride; Pay attention to intention, deciding to change the plan because the plan didn't feel right; Now its time to go make something. Thanks, Erik.
@ENCurtis 9 ай бұрын
Go make a thing my friend. And have some fun doing it. 👊
@SeattlePaulie 9 ай бұрын
Thanks man! I feel pretty awesome, now that you mention it. 😂😂😂
@SeattlePaulie 9 ай бұрын
You're awesome too. ☕
@ENCurtis 9 ай бұрын
😂🙏
@dbackhusker 2 ай бұрын
“…make the object rather than the tool.” I know many woodworkers who get mired down in building their shops, so much so that they spend all their time building shop jigs. I too prefer to spend my time making my actual projects, furniture, boxes, etc.
@mammothscott1455 7 ай бұрын
I use the “bandsaw” method on all my drawers. Easy to batch out a lot of drawers. Cheers
@CarlYota 9 ай бұрын
Man this video was helpful, interesting, educational, and entertaining… to some degree.
@ENCurtis 9 ай бұрын
Glad it was helpful!
@theofarmmanager267 9 ай бұрын
The guy at 72 and with over 50 years of woodworking beats me by 2 years - but I would guess our experiences and views don’t diverge too much. There are several extremely acceptable ways of cutting dovetails (as with just about everything) plus a load of bad ways. Sometimes, it’s down to what tools you have available and sometimes, it depends on how I (my body) feels. I do use the bandsaw plus router plane plus router - if you have them and can use them (two different things), then why not? If you enjoy doing everything by hand, that’s great. Personally, I like to use power tools for the heavy work and then hand tools for finishing. Sharpening? You’re absolutely right in what you say. My usual answer is “more than you are currently doing”. In cutting those dovetails, I might sharpen and hone the secondary bevel more than your 3 times but that’s just me. Your way of fixing the drawer bottoms is fine but it seems to be a particularly American method. I was taught in the UK, and every high quality UK antique that I’ve studied seems to be the same, to do it differently. Before better glues came around, it was usual to dovetail front and back. After better glues, it was more usual to dovetail the front and rebate (not a dado) the back. More and more cutting edge pieces forego dovetails altogether particularly if they have false overlay fronts. Truthfully, who cares so long as you don’t think that it has to be one way or another.
@ENCurtis 9 ай бұрын
Interesting information regarding the evolution of drawer box constriction alongside the development of modern adhesives. Haven’t considered that but it makes perfect sense!
@theofarmmanager267 9 ай бұрын
@@ENCurtis I have heard the view that hide glue is a very good adhesive witnessed by the longevity of the pieces constructed with it. I would only partially agree. Firstly, the animal bone and hide glues made 2, 3 or 4 centuries ago was of very variable quality; secondly I have enough antique pieces of furniture to know that hide glue fails when it is not mechanically assisted. Today, it seems to me that the only unique point about today’s hide glue is that they are using by products which otherwise might be wasted. However, I don’t think there is any adhesive quality of hide glue that cannot be replicated better by a chemical glue. Unfortunately, I’m old enough to remember the choice of glues available to a small shop nearly 50 years ago. Now, I would suggest we have gone the other way in having so many choices that, frankly, are there to sell glues and not solutions.
@paulmaryon9088 9 ай бұрын
Excellent video, thank you,
@ENCurtis 9 ай бұрын
Glad you liked it!
@gavinmcmillan6222 5 ай бұрын
Love your take on simple jigs and spend time making the piece. I too bash out the simplest jigs to get the job done. Tapering jigs on other you tube channels!! I can pin nail two boards to a piece of ply in about 5 mins.
@emptyheads7989 9 ай бұрын
dovetailtastic mugastic goodness.
@ENCurtis 9 ай бұрын
aaahhhhhhh yeah
@MWeeks9 9 ай бұрын
Man, every time I watch an episode, I am ready to go out and make a thing. I just love all the tips and techniques you give and not in a "HERES 5 THINGS YOU NEED TO BE DOING RIGHT NOW OR EVERYTHING YOU DO SUCKS!!1!" kind of way. Just a dude making stuff and teaching others along the way. Love the mugs, too. I am watching his shop waiting on the right one to drop. Keep on doing the thing dude. You're killing it.
@ENCurtis 9 ай бұрын
Thank you so much!
@devinteske 9 ай бұрын
Thirst trap at 12m15s. That hair tussle and stare. I say good day!
@ENCurtis 9 ай бұрын
😂😂
@TCGE08 9 ай бұрын
I see those earbuds…what’s on your playlist? Nice work and keep the positivity flowing!
@brianhmonks 9 ай бұрын
Very nice video, Eric. I have tried the bandsaw method and it works great but I had to recently dovetail twelve drawers for a Highboy I am building and I used the table saw method to cut the dovetails. It was quick and very accurate. I had to do minimal chisel work after. In my case, I had a table saw blade ground to a 10 degree angle. You then set the blade to 10 degrees on your table saw and with a simple sled you can cut very accurate, adjustable and repeatable dovetails. Just a thought. Of course there are a myriad of ways to cut a dovetail! Cheers, Brian
@ENCurtis 9 ай бұрын
I've considered DTs on the table saw for a long time but haven't gotten around to it just yet. Perhaps at some point down the road...
@terrytopliss9506 9 ай бұрын
Thanks for the video Eric, always interesting and informative.👍👍
@ENCurtis 9 ай бұрын
Thanks for watching!
@RobertCade-zm3cy 9 ай бұрын
Another awesome video! Well done! In addition to understand the technique, you implement it with superb skill. But, the thing you do best, in my old and humble opinion, is communicate. You explain what you’re doing clearly and without sounding like it’s your way or the highway. You instruct, but make it feel like a casual conversation between friends. That makes your videos special. Thanks for the time and effort you put into your work. It’s a benefit to everyone that sees your videos.
@ENCurtis 9 ай бұрын
Thank you so much. I really appreciate the kind words 🙂
@AusWorkshop 9 ай бұрын
Nice! You won't get much expansion and contraction on plywood that size anyway but it’s good to see I'm not the only one gluing the front and skipping the nails on the back. It’s just not necessary with modern pva and a tight fit ar the front.
@mattrinne 9 ай бұрын
This reminds me I need to look up Matt Cremona's band saw dovetail method. Worth a watch. Or rewatch.
@captainwoodworking1273 9 ай бұрын
I love your videos and your honesty keep up the good work.
@ENCurtis 9 ай бұрын
Thank you! Will do!
@Copeaux-and-Co 9 ай бұрын
Look, the way you work, thé way you talk, thé way you are... I love watching your vids. You give a lot. So you deserve it.
@ENCurtis 9 ай бұрын
Thank you so much 😀
@mikedurkee7296 9 ай бұрын
I make unique one off cribbage boards so will I ever do a dovetail? most likely not but absolutely love watching... great style, editing, humor, and mad skills. Thank you for the time you take to do this KZfaq thing.
@ENCurtis 9 ай бұрын
Thank you so much 🙂
@andygorski6318 9 ай бұрын
KZfaqrs love for the trim router.
@beardy-bandit 9 ай бұрын
Encurtis podcast when? 😂 Great video
@roofermarc1 6 ай бұрын
Dude those are nice hand cut dt's all the way. Good design
@spinkey4842 9 ай бұрын
i'd like to see one of them fancy coffee mugs carved outa wood.
@ENCurtis 9 ай бұрын
That would be DOPE. Perhaps one day.
@robertjones8021 9 ай бұрын
I love this channel!!!
@hanspeter9630 9 ай бұрын
Frank Klausz actually uses a router to remove the waste of half blind dovetails as well
@TomTom31ify 9 ай бұрын
If Frank does it, then you can't argue!
@ENCurtis 9 ай бұрын
Well I'll be damned. Like Tom said, if it's good enough for frank, it's good enough for me!
@kevinorr6880 9 ай бұрын
Very cool mug.
@markprochaska6756 9 ай бұрын
Very entertaining and educational.Keep it up!
@jimrosson6702 9 ай бұрын
Great video as always cool to see a different way to make dove tails. Thanks for sharing
@edwardnorek8506 9 ай бұрын
Efficiency is an often overlooked tool in the shop. Hand tool work is cathartic and a wonderful meditative process (Most of the time lol) but if there are faster more efficient ways to get the same results, then why not employ them if you have the tools available? It is almost physically painful to watch some videos that are on youtube just because of the methods and tools the maker is using are so woefully inefficient for the job they are doing. I try to remind myself that not everyone has all the same tools I have access to though so I usually just skip through the process and get to the end product and figure out my own process to reach the final result. Good video and I didn't know the different ratio for hardwood and softwood for dovetails always just thought that was a design element of the makers choice. It's a good day when I learn new things. 👍
@Art-is-craft 9 ай бұрын
A standard hand cut dovetail is easy, quick to cut and perfect for craft work. Now if a shop is running hundreds of repeat joints then machines are a good choice.
@ENCurtis 9 ай бұрын
100%. For many who do this as a hobby, the process is the enjoyment. For others, it's the object itself. Efficiency helps us get to the end a bit faster so we can reflect and start again.
@scottcallan3897 9 ай бұрын
Once again, great work. outstanding video
@ENCurtis 9 ай бұрын
Thank you! Cheers!
@allisonwoods6161 9 ай бұрын
Cool gigs
@donesry2902 9 ай бұрын
Thanks for another inspiring video. I like your philosophy on jigs and I write all over mine in pencil too. I think jigs are for either saving time or making repeatable cuts. Also mine don’t last forever because I not great with storing them…
@ENCurtis 9 ай бұрын
Thanks, Don!
@jameslord7082 2 ай бұрын
❤ solid!
@csehszlovakze 9 ай бұрын
JSK-koubou makes excellent jigs BTW, in case someone wants a suggestion.
@timcurtin36 9 ай бұрын
I will have to give this a try. Thanks for the great content.
@ENCurtis 9 ай бұрын
Thank you!
@walterrider9600 9 ай бұрын
thank you .
@ENCurtis 9 ай бұрын
No thank you!
@genghisbunny 9 ай бұрын
Very nice, i might actually be tempted to dovetail with this technique!
@ENCurtis 9 ай бұрын
Go for it! It was a breeze.
@rolandgdean 9 ай бұрын
Thanks for showing us your drawers.
@ENCurtis 9 ай бұрын
Haha you're welcome!
@pauldinella1936 7 ай бұрын
Hey just started watching your videos. Keep it up they are very enjoyable. Noticed the book in the background. Have you been to the Mercer museum in Doylestown? Huge tool museum.
@Realism91 9 ай бұрын
I used a thin kerf circular saw blade and ground every second tooth off with my CBN wheel use a blade stiffener set and boom clean cuts 11° (the teeth were that angle) without getting a $200 dovetail grind blade, mines thinner too thin enough to trick people into thinking it couldn't be done with a table saw.
@steve6271 9 ай бұрын
Nice to see other new and interesting ways to get the same thing done. What bit did you use in the router. I happen to have the same router Thanks for showing new and inovative ways to get things done Cheers
@donesry2902 9 ай бұрын
I too use that hand router technique. My favorite bits are from Whiteside made in North Carolina. I find they leave the least amount of burn marks. But I chop out most of the waste first and then use the router to get the bottom perfectly flat but I don’t go right to the edge because it can go wrong quickly
@ENCurtis 9 ай бұрын
Thank you. That was a spiral upcut bit, 1/4". I believe it was from Whiteside if I recall correctly.
@steve6271 9 ай бұрын
thanks @@ENCurtis
@krawec1958 Ай бұрын
Who is the artist for your theme music I love to here more of there music. I really enjoy your videos and your way of teaching woodworking.
@MrFingeroo 9 ай бұрын
obviously enjoyed everything, as always, but very much enjoyed how you didn't try to find the right corner of the screen for the related video link this time x
@ENCurtis 9 ай бұрын
hahaha thanks
@jessevardaman6208 9 ай бұрын
Another great teaching moment. Do you cut through the jig when you are cutting the tails on the band saw?
@ENCurtis 9 ай бұрын
You certainly can. Or you can cut the top of the sled to the same angle (~10 deg) so that the shoulder of the dovetail is always square to the jig. That way you avoid damaging the sled.
@christopherpawelko4446 9 ай бұрын
Great video. Nice to see other techniques to cut dovetails. Where do you purchase Liberon finishing oil from?
@ENCurtis 9 ай бұрын
Thank you! I usually purchase on Amazon since they don’t have a proper American distributor.
@dandanklerdandankler2244 9 ай бұрын
Love your content, I’m glad I stumbled across it about a month ago. Was wondering where you acquired your fence for your table saw?
@FearsomeWarrior 9 ай бұрын
Looks like a Rockler sled if you’re taking about the light white with blue stops. If you mean the aluminum extrusion that can be turned, that is a Harvey that comes with the Harvey table saw.
@ENCurtis 9 ай бұрын
Thank you! And yes, @fearsomewarrior has it right. The fence is from Harvey. The crosscut sled is from Rockler.
@jamesvaughn4894 9 ай бұрын
Could there be a video of a display case to show the coffee mugs coming up in the future?
@ENCurtis 9 ай бұрын
Oh you read my mind...
@kudnabeefhooked5285 8 ай бұрын
Which marking gauge do you use? Love your stuff keep up the good work.
@xZombieKthulux 9 ай бұрын
Just had my trim router jump off my workpiece and hit my knuckle on my trigger finger. Been out of work for a couple weeks now. Be careful with that thing, make sure you're not making climb cuts and are using the appropriate bits! Beautiful dovetails btw
@ENCurtis 9 ай бұрын
Sorry to hear that. Yes you gotta be careful when freehand routing
@mypony891 5 ай бұрын
Almost always love your videos! Great content! .... .. Sorry though, i can't stand the coffee mugs lol.
@jshanab42 9 ай бұрын
You got the bandsaw, you got the thick cherry, Would it be Sacrilege or an Idea to make a 1/8 thick flitch of veneers, make all the dovetails thru, then glue on the veneer converting to blind dovetails, hiding the groove, and get some grain matching..
@skippylippy547 9 ай бұрын
Frankly speaking, I don't know enough to disagree with you on ANYTHING! 🤣😂 So I'll just watch and enjoy your magic! Meanwhile I will enjoy time in the shop making sawdust. 🤪 It's comforting, ya know?
@ENCurtis 9 ай бұрын
Haha it's all about that enjoyment!
@richardweiler1552 9 ай бұрын
How did you allow for wood movement in the bottom in the long drawer? Looks like the grain runs parallel to the grain in the sides. Good video.
@robohippy 9 ай бұрын
I had to come back and look at that dove tail lay out jig thing you have. Since I do my layout with a knife, I would need a metal one. Do you have a source for that jig?
@ENCurtis 9 ай бұрын
It was made by a friend of mine. I asked if he sells them to the public and unfortunately he doesn't. Sorry!
@electronsmove 5 ай бұрын
All drawers matter.
@geico1975 9 ай бұрын
Very nice, which Dovetail "hand" saw were you using?
@ENCurtis 9 ай бұрын
It's an old $20 Crown gents saw. Still my favorite.
@caspianderrick2943 9 ай бұрын
I confess to being a tad disappointed you missed the opportunity to use the phrase 'get jiggy with it' but hey, there's always tomorrow..
@ismaelgurrola8025 4 ай бұрын
Love the remarks on jigs. I'm the same way. I wanna get to my project not spend extra time on jigs
@distortedodin 9 ай бұрын
Would you mind telling me what type of router bits you used? I'm very new to using a router and didn't recognize the type you were using. Not the brand necessarily, the cutter type. Btw the "special effects" in the video were nice...very smooth!
@ENCurtis 9 ай бұрын
Thank you! That was a 1/4" spiral upcut. From Whiteside I believe.
@ndamico1 9 ай бұрын
You should totally make a pencil sharpening jig. That would be the s*!t
@ENCurtis 9 ай бұрын
I'll do a 13 minute video on making an epic pencil sharpening jig just to upset the internet 😂
@woodnotestudio 9 ай бұрын
I really liked the bandsaw method. Never thought of that. I’m going to try it. Also, not sure if you’re a fellow Phillies fan since you are there, Harper shaved the beard, are you following and doing the same? Hahahahaha
@ENCurtis 9 ай бұрын
Hahaha I'll tell you what, if I hit 100k by the end of the year, I will shave the beard for charity. Spread the word.
@woodnotestudio 9 ай бұрын
@@ENCurtis oh wow that is quite a statement. Hahahaha. I don’t have a preference but if it helps you get to 100k than I’m happy to help.
@contestwill1556 9 ай бұрын
meanwhile im over here with the fastest dovetails east of my western neighbor and west of my eastern neighbor
@ENCurtis 9 ай бұрын
hey fast is fast 😂
@tonysutton6559 9 ай бұрын
Do you like the cold coffee that you drink at the end of your videos? 😃
@ENCurtis 9 ай бұрын
Always! 😂
@renatalima1520 9 ай бұрын
I loved your mug, I want one how do I buy? I'm from Brazil
@ENCurtis 9 ай бұрын
Thank you! It's from my buddy DBowenSculptures on IG. He's great.
@acijami 9 ай бұрын
I MUST KNOW... does your cyclops have his own toofbrush?!
@ENCurtis 9 ай бұрын
He really should before tooth decay sets in 😂
@ronaldpflieger8098 9 ай бұрын
What's the song that starts playing while he's jogging out the blind pins?
@ENCurtis 9 ай бұрын
It's called Baptized and Burried by Will Harrison
@ronaldpflieger8098 9 ай бұрын
@@ENCurtis awesome thanks, new song to listen to in the woodshop.
@jasondale503 5 ай бұрын
Could you put a fake dovetail in the left side of the box where the draw is?? Just asking to make it a drama 😂
@AmericansWillRise 9 ай бұрын
Well...... do you like snakes?? Ball Pythons, to be more specific?? Then, I could get in on the giving, too. 🤷♂️😂
@ENCurtis 9 ай бұрын
😂 Cant say I've ever considered it before
@AmericansWillRise 9 ай бұрын
@@ENCurtis Well...... $#!T. 😂🤣
Bon Bon Media
Рет қаралды 6 МЛН
ENCurtis
Рет қаралды 33 М.
Мастерская Настроения
Рет қаралды 526 М.
Sierra & Rhia FAM
Рет қаралды 3,6 МЛН