Nice I will watch this later on tonight, I get my parts tomorrow I copied you , so far I did the motor with the pinion gear 11 tooth, I'm waiting for the overdrive gear set and rear stock gear set just harden steel as well as the front brass portal and knuckles, SSD wheels with proline trepadors.

Food for thought. I don't post a lot of videos but what I did, was make a GoPro Mount and a phone attachment on to my radios. So I just point my radio at the rig that way I can easily rear steer and video. Love your videos! Cheers from Duchesne, Utah

Those wheels and tires were meant for this rig, just eye candy! And it's pretty good crawler too!!

She turned out beautiful,, very nice Capra now, i watched the build and now first run, great infomation ,editing, filming, to hats off to you Logan!!! you pull some fine lines,, smash that like people!!!!

I got an old AX10 3 gear in a WDW 3 link Capra and a Vanquish 3 gear in a WDW 4ws winch/suck down Capra. Both on a Vader skid plate. Love them

you can underdrive the rear ring and pinion.

Thought you were jambed up, ~21:43. Nope. Nice driving, especially while manually aiming a phone. Love my Capra 4WS. :)

Thanks for the videos! Will be down that way end of March to do some crawling

Looks sweet, works well, and can't wait to see the next version. I have a Capra with your 3 link kit and AR45 portals from a 10.3. With 90mm shocks it looks great and seems to work well so far.

I did an axe 1400 kv and pinioned up. the axe 2100 with 11 tooth 32 pitch was great but the low speed of a 1400 kv axe with 14 to 17 and 12.5 or 46 percent overdrive right now. might add 12.5 to the rear and the 46 to the front for 33.5 front overdrive. desert lizard droop shocks , reefs 777 front 444 rear, SSD kuckles with amazon heavy brass filed down to fit together for a few extra grams. Last thing is I have kept the dig with an 8.4 volt micro servo from homes hobby with the servo saver. Top rig tied with my VRD carbon. they both clear a few lines the other truck can't touch so still trying to declair and overall winner.

Man the rig is looking & performing nice 👌

To make life a bit easier, I think Sidney could hold the cell phone for you 😁

Omg dude rear steer and holding phone. I’m no WDW but I am so used to the one hand thing it is second nature at this point. Man what a beautiful build dude so sharp with those tires….looks perfect half dirty. You are the master at describing what you want the car to do.

I have my rear steer on a three position switch. Left/right and straight. Just allows me to use it easily with the thumb rather than a dial.

Shocks had not struggling the whole time

Even pinioned down with Fusion SE, my Capra 4WS is faster than I want it to be. I currently have 37% OD installed and thinking of underdriving f and r ring and pinion if I can find some that will work

What is your opinion on a rear link riser? I noticed you didn't run one on this build.

What would be a good platform to build of

So what else would you do differently to make it purferm like your other ones

With the iphone, the videos seem very over-exposed, washed out. Maybe need a filter or polarizer? Dunno, I'm far from a video expert.

What spectrum battery will fit in the 1.9 Capra

Hey Logan. If I ended up getting desert lizard shocks would I recommend 90mm or 100mm. Let me know your thoughts thanks.

For increasing the wheelbase do you add the 5525 just to the axle end of the links?

Hey Logan, nice Capra have a Question about f9 axles gears should I go with underdrive gears in the rear or stick with stock gears. Doing overdrive portal gears in the front it is for an rock pirates build. Mike and going with a 3 gear trans

so when you cut and shut the tires is it for width of the tire ? and are you making the tire bigger or smaller ?

I just finished a Capra build where I used Rock Pirates Interceptor skid plate to mount a 3 gear Amazon transmission with dig, swapped trx4 axles with a servo on axle mount, over drive front, underdrive rear, stretched wheel base, 1.9 trepadors on Amazon deep dish wheels, 90mm shocks, & a fusion se 💯👌🏼

What did u do swap panels too? I don’t think u can get a black cage with those panels?

do you know if your 3 link kit will work with the new SCX10 Pro portal kit?

Do you have a video of your fusion pro settings on this rig?

Any concerns on over stressing/burning up the BEC in the Fusion with two steering servos? Want to go this route but don’t want to cook the BEC.

Wheel and tire are om point.

Let’s gooooo

Why did you take the treps off do these tires work better

I have a question. Does the Hobbywing Fusion Pro fit directly into the VDR Stance RTR?

21:50ish - how🤷🏻‍♂

I use stealth x and skid in my capras. 100% better

love the content but please get back to the gopro!

What servo horn is that?

Really like your videos and the quality videos you put out but these overexposed videos are hard to watch lol. Couldn’t even get past 10 minutes on this one.

maybe lower the rig to lower the CG

Those vision wheels are tits!

This isn't a shot by any means but I'd rather wait for a video than have you film on the iPhone again, it washes out so bad that I can barely see the terrain

Looks sweet, works well, and can't wait to see the next version. I have a Capra with your 3 link kit and AR45 portals from a 10.3. With 90mm shocks it looks great and seems to work well so far.