Patience: The most valuable, yet most misplaced tool anyone can own! This was great Felix, thank you for filling in the blanks for us.

Files - check, Sandpaper - check, Leather strop - check, Patience - I'll just go buy one.

Das magische Wort, Geduld :D

Fantastic video,, I'm straight away, going to my shed, to find an old ring spanner, ha ha.. Thank you so much..

Like a lot of these videos I’m a bit late, but I rewatched this video this evening, and realised I had a couple of cheap spanners in the garage after all, so I went in there (my hideaway!) and modified the 13mm ring. Not entirely successful, but I usually have to ‘have a go’ once so that I can more fully understand the instructions! It’s working, it needs fine tuning but it’s working. If it goes well I might manage with the 13mm, but I have a 14mm in case I need to reset the project. Thanks Felix, you’re a gem! Les in UK 🇬🇧

Thanks again for one more inspiring idea on video. Being a steel guy, I like to suggest some ideas to improve the tool. You could also start with a straight double ring wrench acc. to DIN 837 B / ISO 3318. Then one wrench might be good for two carving tools of different size. Also, you can bend the ring to the desired angel after heating the bending spot until it's glowing bright red. Heating the ring to the same glowing color for 10 minutes in charcoal fire in your grille and letting it cool down slowly will soften the steel and make the file work easier. When your done with coarse sharpening, just heat it up again to red glow and quench it in cold water to harden the steel. With some luck you reach 55 HRC with allows higher sharpness and better edge retention. Don't do the heat treatment with a soldering torch or other blue flame to avoid decarbonization of the outer steel layers.

I LOVE that you have demonstrated how to make this with the most basic of tools! Anyone can do this with power tools but when tools are limited, it's a new challenge! So happy that I stumbled across your video, thank you from the USA!

Again, you found me how to spend a zen saturday morning

Finally a use for cheap Chinese wrenchs

Next week: How to remake a wrench from a carving knife if needed. :D

The drawings help to explain. Definitly better than people just talking and throwing words around!

Praise the Lord Felix! I saw a _really excellent_ video on how to do _just this_ but it relied largely on power tools. Read _entirely_ on power tools.

Dremmel has a flexable drive my dad was a Harvard dentist he had air drill that was great too . can not wait untill Friday for another video !!!

You make the most amazing tools out of virtually nothing! I made a comment about what one item I would bring with me if I was ever on one of those silly "reality" shows like "Naked and Afraid." I said I would bring my SAK… well, I have changed my mind…. I would bring YOU!! 🤣🤣🤣🤣🤣🤣

Thank you! Was actually looking at purchasing a spoon knife, but now I'm heading to my crate of old tools.

Du bist ein Meister mit jedem Werkzeug lieber Felix! Tolle Idee, seid Du angefangen hast den Schraubendreher zu schleifen ;) LG Sepp

Hello from Detroit Michigan USA brother great video

Dear Brother Felix, I used to collect antique rifles. I have made gun parts from hard steel. By hand. Diamond files were a godsend! Patience. Slow but sure patience. I can see myself in making this tool. I have made many a spoon from wood, starting at age 12. I am now 68. Another genius course. I need to start buying your books! Only the best from the best, Mr. Felix Immler, the Swiss Genius!

Servus Felix, vielen Dank fürs zeigen. Morgen gehe ich mit den Kindern zu unserer Waldhütte. Da werden wir uns mal versuchen ob wir das auch so gut wie Du hin bekommen. Gruß Sven

Wonderful project people like you keep dummies like me wood working agin thank you for your time and help

Wow!! I really love this project my friend! Perfect! Congrats and thanks for sharing!

I bet you can make an excellent spoon carving tool by sharpening the cuticle pusher on the Victorinox MiniChamp.

This is great info for a retired mechanic with several worn out wrenches and lots of time on his hands. I seem to spend most of my free time making wood working tools so maybe I was a better former mechanic a

Nice idea!

Nice work Felix!!!!

Thank for this tips and tricks. I liike your approach and that you make so simple and inexensive crafts. 👏💯

Felix, it is pronounced 12 hundred (1200). Love your videos. I have a few extra wrenches, I’m going to give this a try. Best Regards.

Fantastic Felix, fantastic! Good life!

Felix would be the best neighbor anyone could have.

Very cool and informative..Thanks for a well done video. Going to make a couple. Greetings from minnesota USA.

GUTEN MORGEN HERR IMMLER!!!!

Thanks, Mr. Felix!

You have inspired me sir. Just bought a wrench and rat tail file…

Thank you,Felix.👊🏼

Fantastic. I'm going to have a go... Just got to go raid my dad's toolbox now 🤣

Thank you,Felix!

This is a great idea. It makes being able to fit the size of carving tool to the size you need. A small one would make small projects easier to do and larger ones would work for large projects.👏👍🧐

I have 3 old wrenches I'll be transforming into these spoon and bowl carving tools...3/4-12mm-22mm should give a good start on learning how to make one! Thanks so much for sharing this knowledge with us! Cheers, Jerbs 👍🏼🔥🔪🇨🇦

I'm going to try to make one!😀 time and patience.

Wow, that _screeching_ !

Excellent work Felix.

My next project. Thanks!

Great tutorial 👍 I guess if you wanted you could make different size ones from larger or smaller wrenches 😉

Thanks for the tips I will be making some of those for sure 👍👍🌟🌟🌟🌟👍👍

Your energy is wonderful!! Thanks for the great video, I look forward to watching more 😁

What a cool idea!

Good for cutting holes in thin leather, canvas etc. Can just turn it in or give it a light tap, with an end block of wood for backing.

Congratulations !!!!!!! Thanks.

I love your mind oh mygoodness brilliant such detail

Awesome Felix! Thank you!

Damn! Where is my 17mm wrench? Oh, I used it to make a carving knife! Great video, Felix!

it will cut fine with both sides sharpened but positive side doesn't get used much. it does come in handy occasionally.

Gud'n Felix! Wenn ich sooo schnell feilen und schleifen könnte, ich würde die Dinger in Serie produzieren! Schöne Anleitung, vielen Dank dafür. Notiz an mich, Kauf endlich neue Feilen!

I’ll be looking at making one of these thank you

Felix, great video, now I don't have to buy one!!! Thank you...

It is funny that I came across this video as I was scrolling through your channel as I had this same idea about two years ago and did this to three different sizes of wrenches that I picked up at a flea market for a little bit of nothing. I used a die grinder and rotary files to do the bulk of the mterial removal, then hand files, wet/dry sandpaper and round honing stones. I put an adge on both sides of mine to make them more versatile

I have seen these plenty of times before on channels that just show the tool being made. BUT what I really liked was that you explained the things to pay attention to and Best practices to get the best results. Great job as usual. And if you are doing things with hand tools, you better have lots of patience, things dont happen fast with hand tools, but you get to learn the process much more in detail.

I’m impressed as hell dude!

This is such a cool idea 💡 and like the project I have a lot of old wrenches 🔧 and many duplicates 😊and Sunday is my bushcraft day too make cool things so it’s now on my bucket list of projects to do thanks to you and your amazing ideas 👍keep rocking the videos 👊

so much work for this little toll you don't really need for a survival bag (to heavy). but you are great ! BR

I may very well make this. Thanks!

Genau so ist es! Danke lieber Felix . Das Video zeigt mehr, als die Herstellung eines Schnitz Werkzeugs. We are abel!

Brilliant as always, Thanks Felix!

Thank you Felix, very good video

Thanks Felix

Lieber Felix,vielen vielen Dank für´s zeigen. Hab deine Idee gleich mal in die Tat umgesetzt und nachgebaut. Dank Deiner Anleitung kein Problem. Ich hätte nie geglaubt das ein selbst gemachtes Schnitzmesser sich so ins Holz beisst. ( hab mal an knochentrockener Buche getestet ). Für meine nächsten Schnitzprojekte werde ich frische Birke verwenden - und da sollte das Schnitzmesser so richtig räumen ( vor allem ist die Verletzungsgefahr meiner Meinung nach wesentlich geringer als mit einem normalen Löffelschnitzmesser. Hab mir damit schon mal bös´in die Hand geschnitten ). Liebe Grüße vom Niederrhein und bleib gesund Peter

Awesome work. A old trick I learned from my grandfather, when filing metal, use some chaulk, the kind you use on a chalkboard. Not a lot, just enough to stop the squealing when filing.

👏👏👏👏🔝Fantastico,è un piacere vederti all'opera 😉

Great video, thank you for my next project felix

Hallo Felix, danke für diese tolle Anleitung. Ist ein super Werkzeug und es aus einem Schraubenschlüssel zu machen, ist genial! Die besten Grüße ... Oliver

Well done.

Another video where all I can do is step back and say WOW! Thanks again for sharing your skills and knowledge.

Klasse Idee! Gefällt mir gut!

Danke. I appreciate it man.

Your tutorials are wonderful

Thanks felix Great video

Schönes Video, Felix. Klasse Idee mit den Ringschlüssel. So ähnlich sehen auch Ringeisen zum Drechseln aus, vielleicht baue ich mir das mal nach? 🤔😝

Like 953 direto do Brasil!! Show! Excelente ideia. Irei reproduzir. Parabéns!!!

When you see a new video from Felix... you CLICK IT! 😎

Definitely going to make a couple of these.

Another excellent video Felix! I love your videos using just hand tools because I don't have a lot of big bench power tools.

Moin! Schönes Teil - werde ich nachbauen! Gruß Sven

What s great project!

Well done Felix! Thank you!!

You're a genius!

Outstanding 👍

THIS IS A TOTALLY AWESOME IDEA!! THANK YOU!! :)

I've been looking for a big spoon knife and forgot about this brilliant idea! Im going to make one 👍

I really want a hook knife or scorp for carving. I definitely have everything to make one. Cheers Felix

Great job!!

Excellent!

That's awesome Felix! Again you outdone yourself. Thanks for sharing.

Good idea

Innovation at its best ! Thanks Felix !

This is awesome, I am putting this project on my to-do-list!

Brilliantly useful as always 👍

Very clever! Thanks for this one, Felix!

Outstanding video! I can't wait to try this!

Thank you Felix Another cool project for my weekend man cave. Cheers

Great video Felix . Thank you for sharing with us all Top man👍👍