Only part I leaned from was when he used the grinding disc as sand paper.

Проработав 10 лет сварщиком с уверенностью скажу вам, все эти виды манипуляций электродом хрень полная, каждый сварщик выбирает свой стиль сварки так как ему удобно там и работает электродом вовремя сварки. Попадаются иногда такие электроды что приходится постоянно бороться с затеканием шлака изменяя наклон электрода и вращать его в зависемости от горения дуги так как она может плясать изза обмазки.

I've always found putting the disk on a grinder works faster.

Найди российские ОЗС4, И провари в изобилии шлака. Тогда то и поймешь, какой ты сварщик) Видно ведь, что эти электроды сами варят, как бы не водил электродом, чешуя одинаковая, шов одинаковый. Но и то, для видео можно ровнее сделать, чтоб одинаковый шов был, а не ступеньками, наплывами

Most of those weaving techniques only makes sense with MIG

That was the weirdest knock-off of wd-40 I've ever seen and I've run across many. As for the welds, those are. Mostly for mig or tig. Sure you can use them with stick, but unless your skill is 8/10 or better it would not pass union standards.

These videos always cease to amaze me

I haven't welded for thirty years and little has changed being that the people that don't know how are still trying to teach it. Pulling the rod out of the puddle then back in is a heat adjustment not a procedure. Welders know what I'm trying to say. The only trick is getting us to click!

I've been grinding the wrong way all this time!

A couple of those looked too hot and widened out, and one was built too high. I suppose either could be useful depending on a particularly unusual situation… but I usually weld between two different patterns that are a happy medium between all of those - which are 1st a simple two steps forward, one step back basically in a line. Or 2nd pattern if the weld needs to fill in a little extra width or get a bit hotter for deeper penetration I use a circular weave while sorta keeping that similar overlap to the first pattern. I love arc welding because when you have the amps just right you can actually push the electrode down a bit while your welding and feel the molten metal penetrating into the base material, sorta like mixing it up as you go to get that perfect bond.

Укладывать металл ровной ванночкой, и нефиг дережировать электродом на нижнем положении шва, это не вертикал😉

23 года свариваю но чтобы шлак в цвет электрода был нонсенс😂😂

Boa irmão muito bom seu ensinamentos diferente do que já vi, grato quero ver mas, com todos os detalhes é mais tempo 🙌👏👏👏

Aprendi tanto y sin ninguna palabra... Excelente 💪🏼

Muito bom 👏👏👏

I think it's funny how so many people feel obligated to be opposite of troll. Would give a super nice and respectful comment even if the video is garbage.

muito bom!

Gracias, saludos desde Ramos arizpe Coahuila México

I'd love to see an x-ray of those welds.

Few people who make biscuits for a living know these secrets, for welders this is basic knowledge

용접 정말 잘합니다 👍👍👍👏👏👏😸😸😸

Thank you for showing this. I did this in JobCorp

Beautiful. Thank you!

Excelente 👍

แจ๋วๆๆๆๆๆ

EXELENTE COLEGA 👍

I really love your video’s I’m so excited to try it out

GREAT VIDEO , WOW SO MANY PATTERNS YOU USED, THEY ALL LOOK GREAT THANK YOU FOR SHARING ,

Welding really isn’t that complicated. But you can’t just pick a pattern to run and learn. Learn how to control the puddle first before you start slinging it around

Me gusto, muy claro👍, me gustaria otto video asi disiendo cada tipo de electrodo es mejor para usar en cada cordon👨‍🏭💪

No son secretos, es un proceso bien explicado donde prepara adecuadamente el metal base eliminando corrosión y contaminantes. Los movimientos del electrodo y su velocidad de avance logran un cordón de presentación parejo y uniforme. En este caso es en la posición 1G, en plano, como cordón de tapa en unión a tope. Muy buena explicación, muy instructivo. Quedó bastante bueno, evitando sobremonta y socavación. Muy buen video

Great thx for sharing, as a beginner I learned many types of welding.

Quedaron súper bien esas dolfaduras

I l'learn with you! 👍⭐⭐⭐⭐⭐

Те кто только ещё учиться варить, посмотрите в интернете виды швов и для чего они нужны, это лишь малая часть, и для каждой задачи существует свой шов)Насколько я помню, эти швы для хорошей проварки толстого металла и заполнения зазоров)

なるほど！こんなカラフルなフラックスがあるの知らんかったわ！！

Very Nice. Great video. Thank you! :)

👏👏👏👏 Sangat menginspirasi sekali sangat bermanfaat 🙏🙏🙏saya pemula selalu ingin belajar 🙏🙏

Excellent, practice makes better

I can't believe I actually clicked on this, thinking it might have a trick I didn't know. But it is always just kindergarten stuff that any first year welding student would know.

Honestly the only thing I've never seen before is the super cool colored Flux. After doing stringers I want Slag caps that look like a rainbow 🌈

جيد جدا

I'm just doing a straight line to make a result like this.. Btw, thanks!

Yeah, some of those patterns aren't meant for stick welding. I think it's intended for different processes like wire or used while welding a vertical or overhead. It seems to have worked for the most part, but I do believe they're intended for different uses other than stick on flat.

Во всех случаях просто согнал весь металл в кучу, технология шва не только в рисунке, но и в растоянии проходов между собой, а ещо добавлю что эти швы не всё под один электрод, а под разные размеры электродов. Дофига можно прочитать в интернете.

This makes me interested in finding out the qualities of that steel. #geology #metalurgy

amazing welding

I’ve never been creeped out by a welding vid b4

Водиш по разному шви почти одинакові😁😁😁👍👍👍

The weave pattern used is dependent on the configuration and position of the weld you are trying to make. Puddle control is always the primary consideration. Understanding this is what makes a welder competent. If you're getting undercut, or slag inclusions, you're doing it wrong. As an inspector, if I had my choice, if a welder who was trying to get his qual came to me with a test sample with any undercut, I'd fail him right then. He's already shown me he's either incompetent, or doesn't care about his work. But the code permits some. Nevertheless, he's already shown me what kind of welder he will be.

I’m a union iron worker and Weld all The time And not to sure what this is

Thank you

Nice video

Thank you.heart.heart.heart

How did you paint the wailing electrode ?

Que incrível sou marceneiro mais adoro está sua profissão já tive uma máquina de solda e não tive muito sucesso com ela, estou fazendo vídeo para o KZfaq quem sabe mais para frente compro outro máquina 😜 parabéns pelo trabalho que Deus te abençoe sempre

most of that would be flat drag welding with very little movement but it depends on angle like vertical or horizontal or doing ring welding that would take multiple complex angles movements when welding up hill but lot of it zig zag to circular motion and some 8 motion and changing to different movements when doing complex work.

No inicio das aulas na soldagem se aprende que a limpeza é o primeiro passo para se obter uma solda de qualidade

Mantapppp bos'ku salam sukses selalu buat bos ku

Now with welding , doing those different type patterns is that just one way to draw metal from one side and from the other side?

Nice tips and tricks!🔥🔥 thanks👍👍 keep it up!😎😎

For real?!?! Secrets of welding?!?! This is in any welding textbook!!! At least in Russian education. 🤔😊👍I would look at these welding methods, for example, at 50mm with a V-shaped 60° cutting.

beautiful beads

Great absolutely great tutorial I've always wanted to learn about stick welding and made that very easy!!! Thanks for sharing your knowledge and skills.

Basically do any pattern it will just look the same top tip cheers I am a pro now 😎 😉 🙂 👍

สวัสดีครับลวดเชื่อมมิกซ์เป็นสีหาซื้อที่ lazada มีไหมครับ

I like welding 👍

فديو رائع وحلو ... بس يا خيي الحديد الي عم تلحم عليه ١٠ مم ... انا اذا جربت لحم هيك ب لحامي اليومي كان بخشت الحديد من زمان .... هههههههه 😅 تحياتي لك 🥰❤

This is pretty much common sense and that’s basically the Basics you learn as a welder. Or at least this is what I first Lear’s wen I started welding.

بسم الله ما شاء الله عليك

Interesting

I like how you coloured the slag in with nail varnish

The objective is not to pile metal up on the gap but to fill it so it's solid metal all the way through

تحياتي الك من معلم لحام كهرباء من سوريا ياريت تحسن شكل اللحام بالمرات القادمة عشان نقدر نقتنع منك يجب مراعاة نظافة و جمالية اللحام

I’ve never seen colored slag before

احسنتم

And i never searched for this. How about you?

Kalo ini sih udah banyak yg tau. Cuma kalo soal gerakan belom tentu bisa semua di aplikasikan ke besi tipis 0,8mm atau 1mm, bisa bolong2 besinya.

مش فاهم حاجه بس عاش 😂😂❤️

ИДЕАЛЬНО!!! доходчиво и понятно. Интересно эти швы взаимозаменяемы?🤝🤝

I wonder what are the strenghts and weaknesses of each, it also seems like hand writing exercices for welders

So which is the best one?

ชอบๆ

ممتاز

Ferry good 👍🏿👍🏿

Different strokes but the same outcome(physical feature)

These techniques are for tig not for stick or flux welding, I’m just wondering why we don’t have them awesome colored fluxes in the USA

Я первый раз вижу такие разноцветные электроды. Ты сам их покрасил или они заводские?

لعيونك احلى لابك وشير دعما للقناة 😘❤

i get patterns are cool, but why not little circles going all the way through? it leaves a solid weld, requires minimal effort on your part in making a muscle pattern for each pattern and overall can get you through a plate test on 1-4G if you have the correct travel speed and amperage

Porque no dicen cual es la diferencia de un cordón continuo, y la utilidad que aporta cada uno....?

That moment when all the welds end up looking the same 😅 but that material prep we really helpful 😁👍

I feel bad laughing at someone making due with what they have available but damn that cut to using a grinding disk as a scraper was funny.

Look at the heat affected zone coupled with the deposition of each technique. Know them to use them in different situations

А секрет-то в чём???Нижний стыковой можно с лёгкостью заварить без всяких мудрёных пируэтов,просто воткнув электрод в стык.А красота шва не всегда является эталоном качества))).Ну и при такой толщине свариваемого металла,разделка кромок обязательна!Так что данный видеоурок не соответствует названию,да и простони о чём.Предмет надо знать!)))

for stick welding, if I'm working on real project, when do I use the different types of beads, is it about the welder`s preference or it's something I must use in arrange for the project?

Goods

You have a pdf of them designs?

Ferry Good

Is that the pattern of the hair on your wrist or the pattern of the weld