See the Full Restoration Here! There are full write-ups, pictures, and embedded videos in order. DONT MISS IT! friscoboater1995searay.blogspot.com/2012/01/rebuild-begins.html Follow me on Facebook- facebook.com/friscoboater
@mrdiazjr276 жыл бұрын
Great job man.. I went through the same on my 23ft bayliner..had to replace the fuel tank.. but at end of day knowing the work and pride you put into it is priceless..
@miamitreasurehunter12 жыл бұрын
I can't thank you enough for documenting this. Thank YOU!!! You are for sure an expert now at Restoration. I will be watching all your videos!
@randylanhart17965 жыл бұрын
You do fantastic work. You also seem to take it all in stride , which is good after you buy a boat that leaves you in a position that you found yourself in. My hats off too you ! I have learned so much from you about boats that I did not even think about before. Good luck too your family on your mom's illness. I have a good idea on what she and y'all are going through! I am a multiple myeloma ( bone cancer ) survivor... SO FAR!!! LOL . And yes i can laugh about it!! Too mom ... BE STRONG YOUNG LADY!! AND NEVER GIVE UP!!! I was diagnosed in 2015, it broke my back. A malignant tumor was crushing my spinal cord. Almost paralyzed me from mid chest down.major surgery,radiation, chemo,stem cell transplant the whole shebang. I went back too work 361 days later.
@nothinglessthanzero12 жыл бұрын
Awesome video man! Just purchased a 20' fiberglass boat and this video has given me confidence to tackle replacing the deck :) Thanks!
@KWGamers6 жыл бұрын
Holy crap! That is a daunting project. Bravo!
@Thegaragefiles13 жыл бұрын
exciting times, progress is finally progressing, got to love it, great job. I would be done with fiberglassing for awhile when this project finishes.
@carlosmurphy4u16 жыл бұрын
Too bad things didn't work out (lake ready boat) but know with all the nice work you've done now you know what ya got. Nice job.
@luispagan13 жыл бұрын
Good to see you're almost done!!! COngrats!
@25shelby112 жыл бұрын
Man Card right there!! kneeling right on the chop strand mat in shorts!!! Jay been watching you vid here for a bit now, keep up the killer DIY vids!!
@davelocock6 жыл бұрын
Wow, nice job man , you'll have a boat for life now.
@unipalooza.7 жыл бұрын
You are truthfully wanna of the most respectable men I have seen.
@FriscoBoatersGarage7 жыл бұрын
Thank you!
@Ricksos19 жыл бұрын
You always do a first class job on the boat! Very good. I used CPES (Clear Penetrating Epoxy Sealer) on the marine plywood, I should have used the fiber cloth as you did.
@FriscoBoatersGarage9 жыл бұрын
Ricksos1 It depends on what you are doing. The Glass is a must in my boat for strength.
@jackpinnell32048 жыл бұрын
looks awesome!!!! I know you are pleased with your progress and you take pride in your work!
@FriscoBoatersGarage11 жыл бұрын
I used 80 grit. It allows some tooth for the gel to hold onto. I made mine pretty smooth as I wanted it to look really nice. It depends on how warm it is. Most of the time I let it cure just to where it is tacky and then put the second coat down.
@ismaelrodriguez28597 жыл бұрын
did you find the fiberglass local or did you have to order it? I'm in Dallas trying to get some to redo my deck
@randyboyer23064 жыл бұрын
I wish I could find an older bay boat and fix it like your doing. It’s looking good
@aronbechiom5653 жыл бұрын
I see that it has been quite a few years since this video. Just aquired an '88 Seville... going to be doing the stringers and deck. Just curious...what did this part cost... to do stringers, deck, glass and gelcoat. Thanks... awesome work.
@jimg28852 жыл бұрын
Great video. Just wanted to know as I don't think I heard you say what type of resin? Polyester or epoxy. I am wanting to do a boat floor sanding down to get all the rubber carpet backing off so want to put a thin chop strand and resin over the entire floor. Never done this so not sure what resin to use. Any advise would be appreciated..
@rwm10007 жыл бұрын
You did a bang up job!👍
@philbarrows42410 жыл бұрын
Dude, you are an animal!!! NICE WORK!!!!
@crashlife4875 жыл бұрын
When you move on to the next sheet, do you overlap it to the previous or do you put it edge to edge?
@shinyprimer34595 жыл бұрын
Do you have to chop strand the deck if you use marine plywood? Or will 2 coats of resin be enough?Same with stringers. Is peanut butter and tabbing them in enough? Or do you need to use cloth?
@galesams42059 жыл бұрын
Would you be using the West Marine fiberglass system 501-502 ?
@peteshelby214 жыл бұрын
Good video. Was wondering where your get your fiberglass sheets. Thanks
@dongiovani912210 жыл бұрын
Nice I like using the red MEK rather that the clear to me I see the air better and rolll em out I just pulled a mold of a 10ft plug deck and hull gonna make about 5 parts out of those molds
@harryesteves3873 жыл бұрын
I have a 15ft boat with plywood deck. Im gonna glass the deck and get it all sealed. Can i lay the glass matt (chopstrand? As you call it) up the sides a bit up against the gel coat? What i mean is will this seal perfectly up against the gel coat or do i have to grind the gelcoat back until glass is showing..
@sala69612 жыл бұрын
did you also glass over the fuel tank joints? how would you access fuel tank in future? will you need to cut through the glass?
@paulwood23295 жыл бұрын
Nice job bud. Well done.
@johnnycuebas84392 жыл бұрын
Awesome job...thanks for sharing....I will follow your instructions 😀 👍
@H2oToGoWH9 жыл бұрын
In instead of chopped strand can I use fiberglass cloth for the ground?
@raulisoto37347 жыл бұрын
hi how doin hey one question where can i get the fiberglass that you used in this boat...
@proverbs35610005 жыл бұрын
I picked up a small boat i had to take up the floor what type of resin would i'll be using ?
@3dvorator6 жыл бұрын
awesome job, but you may have thought about mahogany plywood for the deck wood job,all in all a very good job
@hihoney11229 жыл бұрын
Hi, I was wondering where you bought the chopped strand,? and if you could list what is needed resin and Gel coat? I have a different project I want to seal with fiberglass. I do like how your showing some of your technique this will help me in my own design, thanks
@dn52n565 жыл бұрын
would be great to see a larger sea ray getting it done. I have a DA 300 and they put the carpet from wall to wall then installed every thing on top of it. had to just cut it off at the edge of my doors and cabinets. Also i need to get too my water tank with out destroying most of the steps . does any one have vids on these job's?
@dirkdiggler12426 жыл бұрын
Homeowners association? ¿ nice job....the grandkids will get to use it!
@simondelaney29584 жыл бұрын
So 4 layers of glass on the stringers and 2 on the deck, how long were the screws you used and what was the spacing and you glued the deck down I believe?!?!, what glue did you use?
@derrickmurphy99886 жыл бұрын
Good work man well done.
@DarkcloudGamer-hu4gv9 жыл бұрын
What resin did you use and what kind or weight of chop strand did you use?
@w3stcoastcr3w12 жыл бұрын
I'm a fibreglass noob, found this really useful, thx for uploading ;)
@markjennings23155 жыл бұрын
Wow, have you made this super strong or is this how all boats are made? Super rigid structure. You should name the boat USS GRP.
@michaelpeck55474 жыл бұрын
If a board is already epoxied and dried, is it too late to glass over or can I wet it with the epoxy resin, put on the chopped strand and then wet it down like you did?
@WBeavers111 жыл бұрын
Hey Jay, what did you use to sand/ grind before applying gel coat. I am to that point now. How smooth does it need to be? How much time between coats do you have to wait. I got gel coat from US Composites like you told me. Thanks Bill
@TreLEEloko7 жыл бұрын
QUESTION.....DO YOU RESIN BOTH SIDES OF THE WOOD?
@droski3311 жыл бұрын
How did you glass the bottom as well? Prior to installing deck and foaming?
@peteshelby214 жыл бұрын
How much alltogether resin dod you use? After all said and done.
@deewatts313911 жыл бұрын
hey man you can save alot of resin if ya use a metal notch roller!!
@FriscoBoatersGarage11 жыл бұрын
I used one fore while and just did not like the results as much. You are right though.
@evanfrazier791610 жыл бұрын
Bravo Sir!......Bravo....I didn't hear your wifes voice in the background once. To you sir I say Bravo!
@fredfrenchy Жыл бұрын
What Type Of roller are you using? Sponge rollers break up. Thanks
@jbryan211 жыл бұрын
Did you do the bottom of the wood?
@jamesgould208411 жыл бұрын
you do good work sir...unrelated to the deck but to you know a good site to get parts for pre alpha merc?
@WBeavers112 жыл бұрын
Jay, what weight chop strand did you use for deck?
@00f150lawest12 жыл бұрын
I watched your video and I am redoing the floor in my center console. I did my first layer of fiberglass today and it turned out like crap! I'm guessing that doing it in the sun, using a brush, and having a metal roller wasn't a good idea.
@tasmania10512 жыл бұрын
Where did you get the fiberglass mat?
@kensheely791510 жыл бұрын
Do you take questions via email? You've inspired me to try and fix this repair myself.
@zeppelin6763712 жыл бұрын
Is this how the boat was originally put together? I ask because that seems like alot of weight being added?
@mikeg08026 жыл бұрын
This guy is my hero
@KnolramX12 жыл бұрын
extremely helpful vid. good job
@WBeavers111 жыл бұрын
What do you use to sand with?
@andymusgrave112 жыл бұрын
hi mate, the resin you use is much runnier than Im used to. is it a special kind of resin? whenever ive used resin it has not been pourable like yours, it has had the consistancy of warm treacle? just wondering what kind it is? cheers
@tjs_welding_and_fabrication12 жыл бұрын
I thought you put 2 layers of CSM on the deck. So did you put a total of 3 ?
@christianwoodman194 жыл бұрын
Were can I order this big pieces like this?
@jameswardtv4272 жыл бұрын
What is the little black round thing with wire at 11:04?
@pmaertens6 жыл бұрын
well you are good man, hard worker
@bullhippo90235 жыл бұрын
A lot of work and slot of materials , people that don't do that type of work have no idea what is envolved. I am doing some major repairs on our sailboat, I have used 9 gallons of epoxy already. My coworkers just don't understand. Keep up the good work. I am considering using polyester in some areas to lower the cost. I see you use it a lot. Have you had any bonding issues ?
@FriscoBoatersGarage11 жыл бұрын
It is a mixture of resin and filler to make it thick. I have a video of it here on my channel
@pontiaco9 жыл бұрын
what is the mixing ratio you use to mix resin with hardener I mean like , do you go by the 10 drops to oz like it says in the can, cause it dries too fast when wixing 8 oz or more..
@FriscoBoatersGarage9 жыл бұрын
raul resto It depends on the brand. The junk from Home depot (elmers or bond) goes off quick no matter what you do. Each manufacturer will let you know what their optimal blend is.
@pontiaco9 жыл бұрын
what is the mixing ratio you use to mix resin
@marcosmorales17734 жыл бұрын
How many gallons of resin did u use?
@bsfishing7073 Жыл бұрын
I’m wondering how it’s holding up after ten years after you finish the project please let me know what mess you are using and if it works for you still
@prettyboyexclusive66143 жыл бұрын
What all you buy to seal it by name
@bradleywilke62702 жыл бұрын
Where do you buy this stuff?
@jstorres4865 ай бұрын
What resin did u use?
@virgina198612 жыл бұрын
what is that roller you are using.
@semban8 жыл бұрын
also you should use a steel roller to get all the air out
@FriscoBoatersGarage12 жыл бұрын
No just two. Is there a film screw up?
@916deez12 жыл бұрын
wow great video thanks for posting
@live454512 жыл бұрын
Hey jay ! Question ? How many gallons of poly did u use for the deck ? I just finished my stringers and about to start cutting my deck out next weekend .. I have 7 gallons left and I have to glass my ribs I'n still .. I'm the guy that has the 86 supra sunsport .. Thanks for all the videos brother .. It helps guys like me make since of all this ..
@FriscoBoatersGarage11 жыл бұрын
Yes
@FriscoBoatersGarage12 жыл бұрын
Make sure you go over to my website friscoboater . com and look at the complete blog. It has lots of pictures too, and will fill in some holes.
@lucksranout3 жыл бұрын
Wait, you didn't finish your boating project?
@FriscoBoatersGarage12 жыл бұрын
LMAO... Man Card. Love it!
@pher356 жыл бұрын
Nice job! I'm curious, why does a boat that's a 95 have a wood floor to begin with? I have a 95 Four Winns that is completely fiberglass. No wood at all. Seems strange that a big company like Sea Ray hadn't modernized their by designs by the 90's.
@FriscoBoatersGarage6 жыл бұрын
I think there is still wood under it, that is what I have seen before. The deck is just a liner backed by a wood deck and stringers. I might be wrong.
@ericdavis38904 жыл бұрын
Not near the price you paid but because of covid our vacation plans got ruined. I used our cation money on a 40 yr old boat. Ready to go they said. Had it out once. Found the 305 motor sinking through the rear mounts due to rot
@BennyFadez6 жыл бұрын
What resin did u use? Im not sure if i should use epoxy or poly and how much i should buy. Slow or fast set? Thank you
@FriscoBoatersGarage6 жыл бұрын
Please watch this entire video. It will explain it all. There is an index on the video that will take you right to the discussion about resin. Please also watch the series from the beginning and I Go into great detail about mixing ratios. kzfaq.info/get/bejne/epiCntmI0LKqe3k.html
@samuelragsdale53258 жыл бұрын
Neat! What did you do about the underside of the deck? did you glass that before you put it in?
@FriscoBoatersGarage8 жыл бұрын
I sure did
@anthonymartinez473511 жыл бұрын
if its cold where u are at boil water n put the rezin in a glass in the boiling water to heat the rezin
@FriscoBoatersGarage13 жыл бұрын
@deepfriedmeatpie Epoxy is over kill. These boats are made from Poly and it is fine for this application.
@jerrylittle89226 жыл бұрын
Where did you order the chop strand and the Resin mix?
@FriscoBoatersGarage6 жыл бұрын
You cant. You have to make it. Here is my video on how to make it kzfaq.info/get/bejne/hJmboNVqv8nYhaM.html
@kevinwick82496 жыл бұрын
Did you use marine ply or outdoor sheathing ?
@FriscoBoatersGarage6 жыл бұрын
A/B ply.
@SgtRollo6113 жыл бұрын
This boat is gona be a TANK!! :-)
@Rampage007694 жыл бұрын
How do you ever get that much resin down without it hardening before you get it down? You must have been moving LOL
@vppnbrent6 жыл бұрын
You do very nice work. Congrats.
@cowlumbus10 жыл бұрын
What is on the back side of the marine wood you used? Is it sealed/painted in some way?
@FriscoBoatersGarage10 жыл бұрын
Resin
@cowlumbus10 жыл бұрын
FriscoJarretts Thanks again. I'm curious as I see many different solutions out there...Resin seems to make sense.
@andrewjackson1108 жыл бұрын
You are awesome man
@FriscoBoatersGarage8 жыл бұрын
+Andrew Jackson Thank you
@mrdiazjr276 жыл бұрын
Andrew Jack
@paulstillar476 жыл бұрын
Looks gourjus, awsome
@beaupfeifferrecordings7 жыл бұрын
Nice Job
@anthonycrostreet9605 жыл бұрын
Bare knees on chopped strand! That`s pretty hardcore