I picked up a Filabot pelletizer to try and fill the gap between mulch and finished filament, and it isn't going well. I've made about 100Kg of virgin filament with this lane, but recycled prints and support is quickly becoming my unicorn. Subscribe and hit the bell to see new videos: tinyurl.com/y42f4ydp If you'd like to see a specific area of interest covered, please leave a comment in the section below! Timecodes: 0:00 Intro 00:24 3D Print Recycling 00:58 Filabot Pelletizer 01:48 The Good 02:52 The Bad 04:14 The Repair 05:58 The Verdict #3DPD #3DPrintedDebris #3DPrinterFarmReviews
@albinoviper28762 жыл бұрын
Hey just clean the screw with a wire brush on a electric drill and use some metal pot and pan scrub brush on it then take some more metal pot and pan scrub brush attach it to a pole connect it to your electric drill and scrub the barrel out as well and everything should be good and if not they will sell you some parts!
@albinoviper28762 жыл бұрын
If high school looking kids wasnt enough for you not to buy that it should of been the price! next time you just want to throw money away, just throw it my way and i sell you straight up garbage so you wont have to figure out later you bought garbage.
@masukomi6 ай бұрын
Because i didn't see anyone else mention it. You might want to consider putting a thermostat switch on the housing, and have that shut down the line if it flips. Short version for those who don't know they're simple & cheap electrical switches that flip ether on or off when a pre-defined temperature threshold is crossed.
@craigstay23952 жыл бұрын
Yes please do a review on making filament from standard pellets! Keep up the great work!
@3DPrintedDebris2 жыл бұрын
Will do! I'm almost done with my Smart Hopper design, and I need to run out some black. I'll try and remember to film it!
@Skidly_Finley5879 Жыл бұрын
Thanks for the video. I was so close to wasting my money and time on that setup. sorry you had to blow that much cash to think green but thank you for saving a bunch of people the time and money.
@3DPrintedDebris Жыл бұрын
Yeah..... Filabot's products are a lot like Anna Kornikova.... Looks great, but seldom wins.
@cyrix_dx2 жыл бұрын
please do the entire line and go through the whole process. Love to know more.
@3DPrintedDebris2 жыл бұрын
Will do!
@PatBrady2052 жыл бұрын
I run my Filabot line most days of the week for 8-10 hours, 15-20kg of material. Definitely a learning curve, but haven’t had issues like this. I’d like to see more of your line in action. Might be a few small things that could be tweaked to get it running smooth.
@3DPrintedDebris2 жыл бұрын
Context is everything. EX2, or EX6? Virgin or Mulch? What material? Already I think it is an EX6, as 20Kg is not possible even with 4043D on the EX2. Most I can get is 8Kg (it slows as heat creeps back to the feed) in a 10 hour run of virgin Ingeo 4043D, which is probably the easiest material on the planet to extrude.
@PatBrady2052 жыл бұрын
@@3DPrintedDebris yeah all of the above at some point in the last year. Pretty sure the size of the pellets your making is the biggest factor, second would be different brands/polymers in the same batch. Colorant letdown and barrel temperature are the factors contributing to loss of pressure in the barrel. It’s possible to get that line running smooth to squeak out the extra profit from your op. Just takes some time, and probably an EX6 plus a water bath. Control is everything. I’ve found far greater job success using material that I make myself. Tighter tolerances and better polymers. Plus the supply chain control is just a dream compared to sourcing from different vendors. Shoot me a message if you want to talk more
@3DPrintedDebris2 жыл бұрын
@@PatBrady205 Its all the same polymer in my case, 3D850.
@sanaaw43772 жыл бұрын
This is very useful video. thanks for the tips. it looks like it must not be left unsupervised during operating.
@3DPrintedDebris2 жыл бұрын
Definitely not. I stopped short of creating an automated compressed air purge, then lost interest with the project. I'll return to it someday.
@2xeverything Жыл бұрын
my EX2 did that for about a year and then the motor stopped extruding all together. Turns out, the motors have carbon brushes that need to be replaced periodically.. you may want to check those.
@3DPrintedDebris Жыл бұрын
The windings basically burned off all of their insulative coatings. The motor was a total loss. It was stalled for over an hour, and the shop was filled with smoke. I'm lucky it didn't ignite!
@henricoderre2 жыл бұрын
I have been looking for a way to shred my failed prints. I hate wasting, but I have a rather large box filled with failed prints waiting for me to find a recycling solution. The box has begun to overflow, and my failed prints are now over spilling onto the floor. I guess it's time to start filling another box. I haven't found a solution I can afford. I'm driven by the fact that it would make economical sense for me to do so. To do this, I'm hoping to invest less than it cost for a low-end printer. Most anything I've found on the net seems especially geared towards industrial users, or people with a machine shop in the garage. I don't have this luxury, nor do I have the resources to make my own shredder and blades. This is especially true if I later want to build an extruder once I find that solution. I now know that you use on average 100kg/month in filament. It struck me that you've run into this problem well before I did. How are you recycling your failed prints?
@3DPrintedDebris2 жыл бұрын
Right now I use mulch as filler on products that need weight. I've been experimenting with recycling for some time but only recently could I really dive into it. Once the holiday rush is done with I'll return to it. I think I'm close, but it did run $20K to get to this point. Industrial lines run upwards of $100K, so I may be unrealistic in expecting 3D Printable filament (to standards) out of this setup. Time will tell.
@Mister_Stork2 жыл бұрын
Great honest review!
@3DPrintedDebris2 жыл бұрын
It is my promise to my followers, nothing but the whole truth.
@Titan3DAZ2 жыл бұрын
Might consider the 3devo system in the future.
@3DPrintedDebris2 жыл бұрын
CNC Kitchen ran a couple of episodes with the 3devo system, and it has the same issue with shards as all of the rest. Inconsistent extrusion, and won't hold tolerances necessary for production printing with recycled material.
@trends-friend2 жыл бұрын
how are you monitoring the pressure? I've had the same issue with material leaking out of the feeder. I believe they've updated the screw/barrel design so that doesn't happen. What year is your EX2?
@3DPrintedDebris2 жыл бұрын
I think 2018. I sent it back once for the heat creep fan fix.
@HotCarTrack2 жыл бұрын
Interesting vid
@3DPrintedDebris2 жыл бұрын
I try!
@73notch2 жыл бұрын
What filament brand do you like best?
@3DPrintedDebris2 жыл бұрын
Protopasta HTPLA for sure!
@srikrishnasaichitakana773 Жыл бұрын
Do have whole recycling setup? I have something to discuss in personal. Are you interested?
@3DPrintedDebris Жыл бұрын
Yes I do. No I won't
@Shredxcam222 жыл бұрын
Sounds like the overloads were not set on the motor or it didnt have any. Bad engineering it sounds Those case fans dont cool those motors barely even at at full speed Just add a proper motor starting circuit with overloads.
@3DPrintedDebris2 жыл бұрын
You're 100% correct. It's on my "to do" list.
@Shredxcam222 жыл бұрын
@@3DPrintedDebris surprised they would sell something without proper protection. Is it from china?
@3DPrintedDebris2 жыл бұрын
@@Shredxcam22 No, Filabot is an American company. I think they use an American 3rd party to do the assembly, and what's why everything is priced so high.