In this video, we continue work on the 1990 Cobalt 202! From running on a hose, to discovering new things about this boat, detail work and more; there's lots of progress before the lake test! Stay tuned for more!
Пікірлер: 30
@nasanctionАй бұрын
In the first video, you showed of the trim in operation, It looked like they were operating against each other. I suspect one side of the hydrolic lines are put on backwards.
@scottmassey43302 ай бұрын
Can’t wait for more. Bought the same boat (in red), in 1988.
@bensboats2 ай бұрын
More on the way!
@bennyverhelle2 ай бұрын
Hi Ben ,more Cobalt videos please ...I bought the same (Condurre 203 1988) as a restoration project. Hope to see your progress soon. Love from Belgium
@bensboats2 ай бұрын
That's awesome! Hope your project went well. Part three is in the works!
@gtadriftz313 ай бұрын
love the videos man🔥
@melvinrawlings14573 ай бұрын
Hell yea I love your channel and content brother. Much love to ya from Maryland❤❤❤
@bensboats3 ай бұрын
Thanks for stopping by!
@HarleydogcrownlineАй бұрын
Pull the pump out of the hold and dump out all of the old fluid. When it sits the fluid can turn to thick snot like clumps and the pump can't move thru the system. Hopefully it didn't get in the rams or you have to pull them apart.
@bensboatsАй бұрын
That's a good tip. I'll try this out, thanks!
@christianwalker73133 ай бұрын
Love the video ! Love all your content !
@bensboats3 ай бұрын
Glad you enjoyed!
@Captain12Davey3 ай бұрын
Hey bud, enjoyed your video. Just want to give you a little help . You need to get a 5 gallon jug of clean gasoline next time and run the engine on the clean gasoline. Most likely have plug all the carb jets with the dirty gas . If you take better protocol at these projects, you’ll save a lot more money.
@bensboats3 ай бұрын
That's helpful!
@Captain12Davey3 ай бұрын
@@bensboats I just get a spare fuel line and just plumb it right in with the 5 gallon tank the fuel pump will draw right from the 5 gallon tank
@brianmooney70093 ай бұрын
So glad i found you channel Ben. Great content and your just a genuine nice person. Also very knowledgeable 😊Brian Seaford long island (Also a boat person)
@bensboats3 ай бұрын
Thanks for stopping by! Boating near long island must be wild compared to my freshwater lake adventures lol
@jeffwalker76403 ай бұрын
Good video! Hopefully lake test goes good.
@bensboats3 ай бұрын
Stay tuned!
@bradwren99243 ай бұрын
Yeah, it’s not the carburetor you got blow by like that just pull the engine rebuild at the rings or toast…👍👍👍
@andreireal9158Ай бұрын
A question not related to this project - why use petrol karcher? In a mobile cleaning that makes sense, but since you are washing in your driveway and using the hose from the water supply, why not to use electric one? Maybe the video didn't catch it right but the spray seems weaker than from an electric k5-k7 models.
@bensboatsАй бұрын
Yeahhhhh its not a great pressure washer, but it gets the job done!
@noobish703 ай бұрын
The hydrolic ram looks like one going out and the other going in probably one is plugged backwards
@Scottinqc3 ай бұрын
that looks like what I was seeing as well...... could also be a check valve at the pump assembled wrong..... had that on one of my boats.... trim pump did diddly squat, until I pulled it apart and reassembled it correctly
@bensboats3 ай бұрын
Yeah I saw that when replaying the footage..... I think there's a chance one ram was replaced before I got the boat. The starboard ram is slightly different than the portside. I'm wondering if someone swapped the lines at the distribution block on the bottom of the transom assembly
@Scottinqc3 ай бұрын
@@bensboatsthat’s about the only place to swap them…… and wouldn’t be the first time someone screwed it up, and just left it for someone else to discover years later…….
@noobish703 ай бұрын
@@bensboats 👍 Cant wait to see it on the water
@Roper-wn1xu3 ай бұрын
FIRST
@bradwren99243 ай бұрын
Hate to say it son but when you have blow by like that, your rings are done, so pull the engine out and rebuild it. That’s your best bet. Other than that you’re wasting your time. Good luck.
@bensboats3 ай бұрын
You'd be surprised....Stay tuned for part three coming soon!