Find True TDC With A Dial Indicator & Degree Wheel : Plus TDC vs True TDC Demonstration

Рет қаралды 29,544

4 жыл бұрын

How to find true TDC (top dead center) with a dial indicator and degree wheel, and I'll show you the difference between just zeroing an indicator at TDC and locating true TDC.
✅Tip Jar (Did this video help or entertain you?)✅
paypal.me/49ccscoot
Degree wheel setup and piston stop method :
• Setting Up A Degree Wh...
Thank you for watching! Please Like and Subscribe if you enjoy the content! Click the bell when you subscribe to make sure you get updates.
Check out the merch : teespring.com/stores/49ccscoot
Patreon : / 49cc

Пікірлер: 32

@JiroProject 2 жыл бұрын

Hands down best explained video I've seen so far. Thanks

@babydyke416 4 жыл бұрын

Best description I've found... I actually kinda understand it now! Thanks!!!

@stevehammel2939 Жыл бұрын

Thank you for making it clear what to do.

@nightriderrv1139 4 жыл бұрын

Very well done and said thank you

@WhataLoadofBull 4 жыл бұрын

Great Video, thank you!

@jayi836 4 жыл бұрын

Very informative thank you

@lilman1796 3 жыл бұрын

Thanks for the video everone, Awesome information!!!! ,keep up the great work everyone, ☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆

@Kevin-cy9cv Жыл бұрын

Thanks, good explanation

@4g63tbig16g Жыл бұрын

Nice content very helpful sir

@Dereyter Жыл бұрын

Excellent!

@rod4530 2 жыл бұрын

Top class.

@ravis9544 3 жыл бұрын

Very nice

@somalia5019 Жыл бұрын

New subscribed from Somalia

@j.patino8148 4 жыл бұрын

friend . I personally love your videos. because you are very good with the short and long hirizontal minarelli engines and with the mentioned clones ... I ask you please to activate the app to subtitles in Spanish of Spain. thank you very much. ....

@49ccscoot 4 жыл бұрын

I turned it on to add Spanish subtitles, but it says I have to upload them. I only speak English. I turned on community contributions though, so if anyone speaks another language I think they can help.

@jyg345 4 жыл бұрын

Me podrás ayudar no se poner en tiempo mi scooter es una Derbi gp1 y puse un mvt DD09

@Greybuiltracing 8 ай бұрын

How can I use a dial indicator with a Honda gx200? With head on .

@MrSandRune 4 жыл бұрын

Just for fun.Following up my blinker problem,after changing parts worth tha new v-clic.I got a used speedometer from ebay uk,and the fuel meter has changed behaviour,and use 1 second,compare to 5sec.I suspect the tank fuel measure,because its on the ground wiring.Its not changed.I also used a diode-front light,wich had serious ripples,blinking 10 times pr second.So 1 component,or several,has changed behaviour in the ground circuit.A 0.2mm copper wire.An industrial el-circuit would had to be removed and replaced for any amount of money,impossible to repair.

@user-np3dn4pd4h 2 жыл бұрын

Hi,excellent video and very good description,i would like to ask you a question,when you find that there is 3 degrees gap in the begining why you don't devide the 3 degrees and just split before and after the 0 as it happens eventually at the end?For example my piston stops moving at -1 btdc and starts again at 2,5 atdc if i set the needle at 0,75 degrees it will be the true tdc?Thanks a lot and greetings from Greece!

@49ccscoot 2 жыл бұрын

It would likely be close or close enough, and you can still go back and forth with the degree wheel and keep trying to make sure it's centered... but a piston stop is a sure way to dial it in and it's very easy when you're used to it.

@user-np3dn4pd4h 2 жыл бұрын

@@49ccscoot thanks a lot for your advise probably i will go for a piston stop tool

@vim_usr2753 5 ай бұрын

At what point does being off damage the engine? In other words, if you were replacing timing chain on a V6 and were off by say 1 degree, would that be catastrophic? What if you were off by 3 degrees? Just curious, thanks for the great video.

@49ccscoot 5 ай бұрын

That would depend on the application. In some racing applications where everything counts, a degree may be a real problem. If you're just aligning a couple of timing marks, a few degrees may not be a big deal. That said, I would always aim for accuracy. There will pretty much always be some error, but it's not tough to get within a degree or less and that's fine in most cases.