Just about finished. This thing takes while to assemble. Took me nearly an hour to un-box the damn thing. That said the instructions are excellent. All screws are separated and packaged by each step which was great. You can do it by yourself but it really is a 2 person job. I kept calling my wife in to help. Be careful on ceiling height. Although the unit fits under a fairly low ceiling, you need to keep sliding 3-4 inch pieces pieces down the rods which are already pretty high. i had to keep pushing the entire unit horizontal so my wife could slide parts down the poles as our ceilings werent tall enough to assemble while the unit was completely vertical. The guy in the vid did a heck of a job on his own
@franfurtboy2114 жыл бұрын
how tall are your ceiling_?
@smileplease4447 жыл бұрын
thank u man. i really appreciate u for the great video.. great man
@AndreKhan7165 жыл бұрын
Thank you, great video!
@tinap.16587 жыл бұрын
how did you remove the swivel pulley from the slider pole, mine is stuck at the top of the slider poles. help!
@Optimization_Coach5 жыл бұрын
How did you get those round rubber grommets in just below the top pulley?
@chrisdemchalk34913 жыл бұрын
Great video! I have one ordered. Could you have assembled it if one side was flush to a wall? Could you have slid into place as alternative? I have space to operate but now have assembly concerns.
@mcbrude6 жыл бұрын
Also, after some experience with this equipment, what is your final impression? Is it a worthwhile investment?
@tonywesdudoni33537 жыл бұрын
How many hours did you needed for?
@Peashoot883 жыл бұрын
U move really quickly like super man
@vunnamnithin95554 жыл бұрын
how many boxes did the complete unit come in?
@jesseascriven4 жыл бұрын
How long did it take to put together?
@lucioinnocenzo23286 жыл бұрын
How did you get it in Europe and how much for the shipping?
@TheMichaku5 жыл бұрын
Hi, thanks for the video. What is the minimal ceiling height you would recommend for assembly (I only have 235 cm)?
@punisher2883 жыл бұрын
Yeahwhat is the minimal ceiling height
@mukundebundidschubastani99053 жыл бұрын
Hello a question how long are the ropes of the bench (in meters) thanks for the answer
@Abdullah-fv3iy7 жыл бұрын
how many hours you need to finish it? please respond
@IronmanPerformance4 жыл бұрын
Assembly time in real time?
@mcbrude6 жыл бұрын
Hello Thomas (or anyone with experience, for that matter): What is the most large/awkward piece in this assembly and would it fit in a economy size car like the VW Passat with the trunk open to the cab for long pieces? I'm trying to get a sense, if there was only one person driving the car, would it be possible to fit everything into such an empty car? I will be disassembling a used Inspire FT2 and packing it up for myself, so there will be no boxes, etc.
@abgrits5 жыл бұрын
1/2 right.
@kazanbeat91846 жыл бұрын
Hi, could someone tell me what are the exact measurements from the bottom. I know the ones in the machine, but I want to know the ones in the base. I need to know if I have enough space. Thanks a lot.
@punisher2883 жыл бұрын
Do you know it?
@LibertiesOverSafety6 жыл бұрын
I just got a FT2. I put it together myself no problem. How do get the slack out of the cables? I have about 8 or 9 inches of slack per side. Any advise is appreciated.
@eriklopez43796 жыл бұрын
KrazyLegs Did you figure it out?
@abgrits6 жыл бұрын
that is not normal slack something is off.
@eriklopez43796 жыл бұрын
If you purchased it with a 200 lb. Wt. Stk. You have to discard the 5 inch metal spacers that come standard with the unit. Did you purchase it with 150 or 200 lb. Stacks.?
@eriklopez43796 жыл бұрын
These metal spacers go under the weight stacks.
@punisher2883 жыл бұрын
How is it going now
@martingetlik15802 жыл бұрын
Môžete mi poslať takú mašinu 👍😉🤣
@t.33827 жыл бұрын
@Abdullah and Tony: it took me about 5 to 6 hours in all
@surfingtim235 жыл бұрын
Thomas Alsch took me 8 hrs haha I had a 30 min lunch break in that span though.
@abgrits5 жыл бұрын
2 1/2.
@ceddric36777 жыл бұрын
and the litle bit low version ?
@saravananvc7 жыл бұрын
Would be great to have a slower version
@t.33827 жыл бұрын
.... sorry for that - but then the video would be even longer and i didn´t want to bore people :-)
@Ematuresco4 жыл бұрын
@@t.3382 hey T. kannst du mir bitte sagen, was du für Werkzeuge gebraucht hast ? Ich muss mir das alles leihen gerade..
@anouarnour28725 жыл бұрын
Please Mr Thoams i had the FT1 i want to developpe it to the new FT2 . if possible . Could you please send me The Catalog assemblies please to see what the new systemes between the first and the second FT2 please bro
@anouarnour28725 жыл бұрын
Please if you accepte to send me the assemblies catalogue that's my Mail zinonooor@gmail.com