Fino Edge Knife Sharpening System Upgrades
Рет қаралды 62,370
3 жыл бұрынDOWNLOAD FILES LINK:
www.thingiverse.com/thing:502...
Upgrades designed by Leading Edge at :
www.thingiverse.com/thing:413...
I also built the "Leading Edge" system available for download at the above address :)
Check my video of the Leading Edge system here:
• "Leading Edge" Knife S...
---------------------------
My only issue ( easily corrected) with the Fino Edge system ( see at end of the video ) is that the screw that holds the vertical rod in position at times may come loose during sharpening and the rod slides down a tiny bit lowering the sharpening angle ( it happened a couple times )
I will make the grooves on the flat portion of the rod bigger/deeper so the screw bites more solidly into it to prevent this from happening.
For now I am putting two or three ball bearings inside the main housing to bring the angle close to what I want and then I adjust/fine tune with the top screw/holder. It's actually working very well that way with no fear that the angle may change.
@burtjoubert 3 жыл бұрын
Great video and nice setup!
@cellodan6353 2 жыл бұрын
Hi Burt, in the comment above Rafael would like the files for the upgrades
@Sdelaj_sam_KH_UA Жыл бұрын
Прикольный конструктор ножемана. Отличная работа.
@bostjanbizjak3952 Жыл бұрын
Top work
@vincentjoseph5726 Жыл бұрын
Sweet little being small hobbyist... knives sharpened tools..i try someday making one similar situation required for knives sharpened
@Houndicon 2 жыл бұрын
do you sell the upgrades?
@cellodan6353 2 жыл бұрын
The designer has made the upgrades available for free. The link to download the files is in the video description Cheers 😊
@rafaelrubalcaba1553 2 жыл бұрын
Where can I find those upgrades?
@cellodan6353 2 жыл бұрын
Go to thingiverse at www.thingiverse.com/thing:4135236 and ask the designer "LeadingEdge" for the files. Alternatively I can email them to you if you provide me with an email
@burtjoubert 2 жыл бұрын
I'll upload my design files for it to Thingiverse. Should be available for you to download in a day or two.
@rafaelrubalcaba1553 2 жыл бұрын
@@burtjoubert ... thanks for the quick response and I was asking about the upgrades because I was actually thinking about getting that same specific sharpener
@burtjoubert 2 жыл бұрын
I've uploaded the design files to Thingiverse, but for some reason KZfaq does not allow me to post the link here in the comments. I'll email the link to CelloDan and ask him to add it to the description of this video. Search Thingiverse for the following design number in the search field: 5025060
@cellodan6353 2 жыл бұрын
Hi Rafael, here I am posting the link for download that the designer just sent me, cheers :) www.thingiverse.com/thing:5025060
@nine971 Жыл бұрын
天才
@NicMALINA Жыл бұрын
на 00:47 видно огромный люфт держателя клинка. В помойку станок
@DA-jw6nm Жыл бұрын
Stainless is not magnetic enough to be trusted
@siriosstar4789 Жыл бұрын
These type of systems suck . they are slow and tedious and the stones that come with them are terrible.
ArtTema Mix
Рет қаралды 1,8 М.
Евгений Масс
Рет қаралды 203 М.
How to sharpen a knife on Fino Edge | Knife sharpening easy on Fino Edge. Knife sharpeners on Amazon
ArtTema Mix
Рет қаралды 864