More videos www.fenyutas.tk Piteba kézi olajrés első próbája, napraforgómag olaj préselésen keresztül.
Пікірлер: 98
@billjohnson69177 жыл бұрын
If you put your end cap back on then your seeds wouldn't just fall out the end. Plus your flame is to hot it is making your cake come out to stiff. But great automation. I think if you move your wheel and sprocket closer it wont bend your press so badly. Your cake should be coming out the two small holes at the end of the shaft by where the adjustment plug goes but it can't because you forgot to put in your end plug. Just some thoughts. If you put in your end adjustment plug you also wont have to hammer out the cake at the end of you session.
@steveciarico9824 Жыл бұрын
Nothing like watching the grass grow...
@farkasarnold2 жыл бұрын
Kedves Fenyutas! 5 év telt el az első próba óta, működik még a prés? Milyen gyakran és mire használta? Mennyire elégedett vele? Ha ideje engedi, kérem ossza meg tapasztalatait. Köszönettel: Arnold
@Everyonespal997 ай бұрын
Last month, I purchased (manual) one on Amazon. I had to buy a thick block of wood to mount it. It did not come with any mounting accessories. So I had buy a thick block of wood for that purpose. That was the only drawback. I had my first test with Sesame seeds and Successfully pressed oil. I can see the difference between store brought and this oil. For some reason, the cake became very hard at the end of the press ( after pressing 250 gm) and it was not coming out of the outlets. I did not understand the reason and stated looking for messages if someone experienced the same and the how they fixed it. Someone said it the flame is too hot, the cake becomes too hard. Let me know your thoughts. Thank you.
@LordWillyGee Жыл бұрын
Nice setup! I thinking of doing the same but mounting a Bicycle, and removing the front tire? Then when done remove the bike, and install the front wheel mean of Transportation.
@y.k.97055 жыл бұрын
Heated oil is sold on stores . Idea of making it yourself is to get COLD EXTRACTOR.
@trollmcclure18844 жыл бұрын
yea, they say you dont need to heat it if the seeds are at room temperature. Maybe some oils are too thick but then again people seem unable to adjust the wick these days
@raffic47153 жыл бұрын
You can directly connect the shaft to the wheel buddy... Thank me later!!!
@beldengi2 жыл бұрын
Did I just see petrol in that bottle? BOOM!
@user-ph2vj7tr8o Жыл бұрын
الله يعطيك العافيه لكن عندي ملاحظه... ألغى المنويل وضع المسنين مباشر على إكس الحلزون ولا داعي للجنزير والمنويل
@marcelodelcampo6421 Жыл бұрын
Como hacer aceite de oliva? Por favor un video, gracias
@5678911007 жыл бұрын
It was like watching mr bean. Sorry, nice contraption though.
@Berat.983 жыл бұрын
I guess the motor washing machine motor you use. The speed of the washing machine motor is too high. Can you tell us how you managed to reduce it?
@gheorghedragan72823 жыл бұрын
You're cool! don't get out of hand at all!
@funwithanimals45433 жыл бұрын
It's a 17th century's way😏
@alfredibidapo66407 жыл бұрын
I am interested in building oil screw press for soybean Seed,Groundnut,and Palm kernel. The press should be able to press 50kg of the above mentioned material in an hour. What are the specifications necessary to meet my need.
@Fenyutas7 жыл бұрын
This machine too little for you. You need a bigger one. The exact specifications of this machine on the PITEBA site.
@WIDEAWAAKETV7 жыл бұрын
Is the the oil lamp necessary? Wouldn't the heat destroy the oil and cause it to go rancid? Compromising the integrity of the oil being produced?
@Fenyutas7 жыл бұрын
It's lamp or edible oil. It's 50-60 C while working. Destroyed??? Perhaps...
@sergeyboev35327 жыл бұрын
UNDIQUE01 кулибин👍
@MortgageMecca5 жыл бұрын
I've read on some medical websites that the best oil extraction is after the seeds have been roasted to 100 degrees Celsius (about 210 F) for no more than 10 minutes and then pressed. The purpose is for best the oil yield - here's a pull from NIH: The different thermal processing protocols yielded three distinct patterns: heating the Nigella Sativa seeds to 50°C, 100°C, or 150°C produced oil with a strong ability to inhibit tumor cell growth; no heating or heating to 25°C had a mild antiproliferative effect; and heating to 200°C or 250°C had no effect. Similar patterns were obtained for the thymoquinone content of the corresponding oils, which showed an excellent correlation with the antiproliferative data. It is proposed that there is an oxidative transition mechanism between quinones after controlled thermal processing of the seeds. While NS oil from heated seeds delayed the expression of NF-κB transcription, non-heated seeds resulted in only 50% inhibition. The data indicate that controlled thermal processing of NS seeds (at 50°C-150°C) produces significantly higher anticancer activity associated with a higher thymoquinone oil content, and inhibits the NF-κB signaling pathway.
@einzigartiggeschaffen7280 Жыл бұрын
🤔 naja...
@MrOlgrumpy6 жыл бұрын
Hmm flame -- hot,like your power drive ,good innovation
@prakashkumerdey50984 жыл бұрын
Hi,, Sir,Can i use a 200 watt ac motor instead of handle to expell the oil? Plz answer me.
@edparrera44553 жыл бұрын
Did you try it ?
@hlimbenmimi73604 жыл бұрын
اين تباع هذي الالة في الجزائر
@abhinavsirohi3 жыл бұрын
Very innovative 👍 oil mill
@bhagwatkathawate32762 жыл бұрын
Good idea पण हॅन्डल la साखळी लावण्या पेक्षा सरळ सायकल che चाकाला फिरणारा rod जोडला पाहिजे
@marlarandall92277 жыл бұрын
These are currently available on Amazon and ebay
@trollmcclure18844 жыл бұрын
Say something godammit! Him: 6:21 :D
@edparrera44553 жыл бұрын
🤙😂
@lisandrourbina90617 жыл бұрын
me gusto mucho pero el sistema de la manivela es un poco forsoza. la pieza se mueve mucho
@chriswieczorek60563 жыл бұрын
hot pressed? :) the flame was way to high
@Balazs031494677 жыл бұрын
egy teljesen értelmetlen meghajtással
@gyanunachhiringnachhiring141 Жыл бұрын
good.
@nunyabiznes33 Жыл бұрын
What was the kerosene lamp for? Did you shell the sunflower seeds first?
@cindyskillman544 Жыл бұрын
You feed the seeds through whole (not shelled). The lamp warms the press. He has the flame too high, though. You shouldn't have the black smoke & black residue on the press. He needs less wick sticking up.
@ranchoelchamusquito36833 жыл бұрын
Good job!
@watchtv40266 жыл бұрын
It is a very Nice Video.
@MiddleEastMilli4 жыл бұрын
Very nice!!!
@harryvendel2903 жыл бұрын
omg! you must support the back of the press, the friction of the metal gets lazy and can break!!!
@shivnani.exactbusiness41913 жыл бұрын
I need this
@samirabdelsamad78296 жыл бұрын
Can it used for other product as Sisma seeds & other?please answer me
@Fenyutas6 жыл бұрын
Hi, sorry I don't understand "sisma", but naturally it's usable to other oilseeds. The point is to have oil content. Have a nice day!
@kerplunkboydotNET8 жыл бұрын
Hello! If possible, could you please tell me the proportions? It looks to me it was about 1.5 kg of seeds to something around 200ml of oil, is more or less this?
@Fenyutas8 жыл бұрын
+kerplunkboy Please see all exact proportions on piteba.com