Thanks for taking the time to show us the finer details of the project...

When I built my workshop I used Isoflex liquid rubber paint on the gutter ends. Keep up the good work 👍🏻

Looks great. Just a note to anyone doing a similar build. Fit red caps to fixings around any skylights.

Great to see this project completed. Looks really good. And that beard is 👍🏻👍🏻

Great vid...true to real life (starting a project and finishing it in a final push some time later). Maybe heat gun and scraper to get rid of the wicking at the eaves?

Excellent Video, answered my question of mixing single sheet lengths with roof lights. Doesn't seem to be a problem.

It's always best practice when putting on flashings to install a timber batton in between the wall and flashing which is shorter/narrower than the flashing to allow water to drip off the flashing and not run down the wall

I thought it was the workshop build for a minute I thought you'd cut us out and cracked on with the cladding without us 🤣🤣🤣🤣

Great job. A bit of bitumen paint under the gutter edge of sheets cured the wicking problem on my horse stables.

Thank you for sharing the mistakes you make, it's so refreshing and reassuring! 👍👍👍👍😊

Looking good, I bought the same sheets for my garage the supplier told me to lighty singe the felt off the sheets at gutter level I used a small gas torch this seems to have stopped any capillary. Thanks for sharing

Thank you Team, nice build cool tips.

I’ve just had a similar single pitch shed built for me yesterday. Single skin steel roof cladding with separate con membrane attached to rafters below. Was concerned that the open ridges at the overhangs would let rain in as no foam fillers were used. Also let’s daylight in like yours. I guess it’s done this way to allow the roof & membrane to breath? Do you find rain gets in there if there’s a driving wind?

When we use the anti-condensation on the steel sjeets we give it a quick coat of varnish along the lower edge - that seems to stop it wicking up the sheet. Might be worth trying it before trying anything too destructive.

Them nail guns are amazing tools. Bit of a pain to get out after though 😎

Hello! Love your content 😁

Maybe try a product like Rain x or another condensation repellent on the clear plastic sheets? Assuming that removing the felting at the gutter end doesn't cure your issue that is.

Would you use this roof for a summer house/ garden room with insulation and an air gap between the roofing and insulation. Just trying to keep costs down on my 3x7m build and that's that's lot of plywood and rubber or felt roofing.!!

On the last two inches of the sheet what goes into the gutter burn the anti con with a blowtorch and that will stop the water tracking back up the sheet

I fit these mental sheets daily almost on the edge it's not meant to have the anti con so the water doesn't soak in to it Also good practice to run a Stanley knife along the underside that over laps the gutter and then just peel it off! This will stop it running up the anti con and rotting the purlins

You can use a small torch to burn the ends of the felt to stop it wicking from the gutter. Easier than cutting it away 👌🏻

How do you stop the rain water from going back in under the roof and into the shed ?

Whereabouts did you buy the roofing from as I would like to use something like this myself for my new shed. Thanks

Remove anti-con with blow torch, carefully 👍

A membrane below the steel roof --would have collected all the condensation.. cheap membrane --not Tyvek.. anyways good job. Had me worried with first board... 10/10

Wouldn't you have liked another 10 inches head height in both out building or was it a planning issue?

When are you going to do a video of finishing the interior? Are you going to put in insulation and then chipboard or plywood?

What’s the name of the roof and the cover trim please. I need this to go over my pond thanks 👍🏻

What make were the boards, also do you find theres any benefit of decking the roof in 11mm osb before the metal sheets or not? I want to totally eliminate any drips when i do a dual pitched external shed of brick construction.

Do you have the details of where the roof materials are from please

You can carefully use a blow torch and burn it of the edge Tim but don't torch it too much

To see you popping up & down through the roof makes me think of "whack a mole" at the country fair. Quite funny. ha ha

Thanks for sharing¡¡ Iam building something similar and I was told that zinc roof might have issues woth condensation and mousture will go inside. Have you had any of this?. Thanks again.

Hi Tim, what is the noise like when it rains

At 15.01 what is the box metal your putting up mate I need this for my concrete shed

can you put that cladding onto brick wall shed/ garden wall?

Hi mate - quick one for you, on my timber framed shed - when i done the roof i have done a overhanged roof frame but have put a couple of sheets of OSB screwed into the frame, this box profile felt lined roofing can that be fixed straight ontop of my OSB to remove the need for using felt or would i be better removing the OSB and fixing it straight onto the framed out roof? plus think it looks a lot better with the edge trimming etc finishing the roof off nicely rather than using felt.

I have the same (or similar roof) and get crazy condensation from it. I have no felt lining up there unfortunately and was wondering if you have any tips? I really want to insulate from floor to roof. Would this be possible with this type of roof? It is a detached single skin brick garage. Thanks. Love what you do, it's so inspirational. 👍

Anyone know what those roof fascia trim things are called? It's exactly what I need on my shed

Beard looks smart

My shed roof is constructed from timber tongue and groove covered with breathable membrane then covered with felt shingles I.e. type on 1 M sheets. I also get wicking at the gutter end, as I suspect that I didn’t leave enough overhang of the roof. Problem is wood is now going black inside so I will have to extend roof overhang. Lessons learned!

I've got similar roofing to replace my old garage roof. Somewhat delayed over the last couple of months as originally supplied incorrectly without drip coat. I learned about the issue of water wicking back up the drip coat and spent a couple of hours removing it from the bottom 150mm of each sheet. So spotted that you had not taken it off. As someone else had commented, a technique used in the states seems to be burning the edge with a blow touch, this stops the drip coat absorbing water.. Nice job as always.

When ever you build a shed you will always find that you haven’t made it big enough for your stuff,(Sod’s law)

How is it for condensation?

Where did you order the roof from? Wickes or did I miss that? The screen shot you included would is a great help... I'm looking to build something similar.

Do these roofs sweat ie condensation?

NOOICE!

Perhaps hit the anti-con with a solvent like acetone along the edge rather than trying to mechanically peel it off.

Level gutter Tim? Should we be putting a fall in it? Roof sheets are great, nice job. Depressing looking at the beautiful sunny weather....I keep thinking spring is here but it was snowing here in Edinburgh today! 🤦🏻‍♂️

Just wait for the anticon to dry then paint with waterproof pva or burn with brazing torch carefully plus you need the foam fillers for eaves and top flashing

I'm wondering why you would want to fix screws through the valleys... in the end they'll always begin to leak and rot the beams below

So wish I had gone this route , I went with the bitumen roofing sheets and they sag after time

I was yelling at the screen the first time you nailed up the board "Tim you didn't flip it!"

Yep, I think when you put the first board up....‘he’s fitting that the wrong way up’...!!!...lol...

I subscribe this is video I needed

Is it a called a 'dripstop' attached to the roof sheets to prevent condensation?

Did you not put OSB under the roof because your not supposed to, or was it to keep cost down 👍

Did Jo handle 'patina-ing' the shed door? It looks very rustic. 8-)

Did pealing the Anti con back 50mm work? As I have the same issue.

Hi may I ask where you got the screw caps from we need some and can’t find them on screw fix etc

That was funny ) flip the top board... )

Additional improvements can be to paint the roof white on both side to reflect heat and to maximise light inside. Keep the metal roof edging and gutter as is. Another is hooking your down pipe gutter to a water tank for your garden.

I wonder if insulated panels are a better idea in a warmer climate? My shed doubles up as a gym and so a metal roof would transform it into a furnace during the summer months. Maybe insulated roof panels (like the wall panels on the workshop would be a better all-in-one solution? (rather than time/cost involved in OSB boards, insulation and a rubber roof cover) Anybody have any experience in a similar situation?

Do you get condensation on the roof in the winter drips?💧

Embrace the beard, helps keep the face warm when working outside.

Was that Price Harry working for you before the lock down?

Vertical storage!!!

have you had it checked for electrical safety ???

Your voice sounds funny, Ron Howard.

Strange, I found myself shouting, "That feather edge is the wrong way around", and then you corrected it. We do silly things when things are so simple to do. Not concentrating fully because it's easy to do. Focus Man, focus! Ha, ha, ha.

We're planning to build a poultry house this summer, the anti condensation roof is very interesting, perhaps you can tell us where you obtained it. I'm not the only person enquiring.

Aww a big "shed" and a workshop that's my dream! and I have neither and my house purchase has just fallen though so probably another 6 months of house hunting 😒. Good work though.

Was gonna say that boards the wrong way up lol

Are these roof panels in Anthracite colour?

Spooky. Just re-watched the build today...

I thought just saw Johnny Bairstow

I didn't see no bird blocker for the roof

Have been seriously flirting with the idea of building a replica but have been using not being confident on how to do the roof as an excuse not to start! No excuses now... 😂

Lockdown beard!!

Where's the door!!! 😢

2023

Turkey.

lol..... I was shouting at the screen, that's not the right way. :)

You need eaves and ridge fillers.

Brilliant, thank you. I detest the American saying...swap this out....just say change it....replace it....English does not have to bastardised....

With that beard, you could stand in for Prince Harry.

YES I’m first 😃😀😄😁

When your head popped out I 100% expected to hear you say "Scott Brown here"

Grow the beard back!

remarkable how little information was conveyed in this video, if ye didnt know how to do it before watching, u definitely wouldnt know how to do it after watching!