In this video we are going to show you how to fix drift for ps5 controller stick. You can buy ps5 controller stick and replace the new one. This video shows the absolute solution for stick drifting in ps5 controllers.
Пікірлер: 117
@aisforashhh34625 ай бұрын
wow this is the easiest way i found..i thought i had to change the whole joystick. needed a heatgun and all that. this is actually much easier to just change the potentiometer. thank you!
@DIYVidss5 ай бұрын
That’s right… we just do it without heatgun. Thanks for your attention ❤️😄
@akselerant9 күн бұрын
There is obvious way if you think a little bit
@SETtheTONE.3 ай бұрын
I replaced the sliders inside for my right joystick & it worked perfectly. This was the first video I watched on the drifting problem so I had to leave a comment.
@DIYVidss3 ай бұрын
Thanks for your attention 🌸🌟
@E.P.1Ай бұрын
Awesome job! Once you broke out the soldering gun, my confidence dropped 😂. You make it easy.
@supermassiveblckman25 күн бұрын
Very useful video (for more reasons) but, since it takes several skills in soldering + perfect soldering iron + perfect tin + perfect soldering iron temperature, tin suction pump (cleaner work) (so, absolutely not base tools as not base skills) to do all this, instead of replacing the potentiometers, I recommend simply using dry cleaner electrical contact spray (perhaps the same one you used to clean the soldering iron) directly on the potentiometers and you will go on for years without replacing the potentiometers... then you will do it with base tools
@wishingW3L4 ай бұрын
opening up the DS4 was so easy and putting it back too but this one seem like a lot of things could go wrong.
@jeremysnader23745 ай бұрын
Start with just cleaning the potetiometer with alcohol or electronic cleaner. The black rings on the green part and just change the white wipers. No soldering needed and works 85 percent of the time. Nice video. The method in video will work best if you have had the controller a long time and are hard on the sticks.
@supermassiveblckman25 күн бұрын
I wrote the same, before reading this 😂
@lesterbruke81663 ай бұрын
Use flux and a copper braid to remove any remaining solder from the contacts. Always use flux when soldering, wetting and surface tension. You can also check the resistance of the potentiometers before installation. And please, clean the soldering iron tip.
@DIYVidss3 ай бұрын
Thanks for your advice 👍🏻🌸
@SaifSKHАй бұрын
Can you install a Hall Effect potentiometer instead of the regular one using this exact method ?? Like would the regular joystick work with a Hall Effect potentiometer or is the hardware different??
@angeloatie737012 күн бұрын
Perfect job
@isulsten83795 ай бұрын
Thanks
@DIYVidss5 ай бұрын
Welcome🌸🌟
@josefpreyes3 ай бұрын
ganda ng video, ganito kelangan natin sa Pinoy KZfaqrs or content creators yun may matutunan ka, hindi puro pa cute at pa raffle
@DIYVidss2 ай бұрын
❤️🌸
@vangoghskye2 ай бұрын
Just take the little round thing out of the green thing and clean both things. Worked for me. I used rubbing alchohol and qtips.
@vangoghskye2 ай бұрын
And I pried it apart with a guitar pick.
@DIYVidss2 ай бұрын
Yes… sometimes it works… thanks for your advice 👍🏻🌸
@Andreas_Straub11 күн бұрын
Better use a Hall Sensor. You can also buy just the compatible hall effect "pots" ... This together with the new calibration sw solves the drift issue permanently.
@Karolina-ls5xl5 ай бұрын
Can you SEND program the base tools?
@alejandrotobienne82205 ай бұрын
OR JUST GRAB HALL EFFECT STICK BOXES. WHY SOLDER IF ITS GOING TO HAPPEN AGAIN.
@dhmhtrhsntekeles36704 ай бұрын
Hello..You play DMZ call of duty with ps5 controller.. I can’t play the game show me the controller of Xbox buttons to play
@Godric_714 ай бұрын
Idea: Could you give a fair price range for each repair that you do? That way, we (the ignorant) have a better better idea of someone giving us a fair shake.
@moisesrodriguez9023Ай бұрын
Man you think you can teach me how to do all the soldering?
@chokz934219 күн бұрын
replace only the white piece inside , more easy , same result 6:05 , no need for unsoldering the whole piece ( the green one ) , but thx man for your time
@mustafartorretto26424 ай бұрын
كيفية ترجيع خطوط مقطوعه انالوج دراع بلايستيشن 4
@troytony805 ай бұрын
Nice video
@DIYVidss5 ай бұрын
Thanks❤️🌟
@Chatooly3 ай бұрын
good video 👍 😁😊 🇩🇴
@DIYVidss3 ай бұрын
Thanks for participating ❤️🌸
@zukesnukem17232 ай бұрын
Which cable is the one you took out on 2:43? I accidentally ripped that one and need to look for a replacement online
@DIYVidss2 ай бұрын
Two bottom side are two mics cables… both sides are triggers … up side is for touch pad.
@pepstriebeck11635 ай бұрын
The orange ones have a different electrical resistance than the green ones. They are not interchangeable! This will usually lead to very high sensitivity. Have you checked the difference?
@DIYVidss5 ай бұрын
You have to change the whole stick if you want to replace an orange one. It works properly and good without difference. It may survive more than usual one.
@pepstriebeck11635 ай бұрын
@@DIYVidss You're right. It works when you change the whole unit and not just the sensor part . I could have been more specific in my comment.
@xXCrazyYouXx6 күн бұрын
Do I need a heat gun?
@danielm41363 ай бұрын
I wanna do this but i’m so terrified of soldering. Especially when it comes down to the black and red wires.. the soldering of the pot looks fairly simple though
@DIYVidss3 ай бұрын
Yes it could be hard for first time 😁
@danielm41363 ай бұрын
@@DIYVidss Do you have instagram by any chance
@DIYVidss3 ай бұрын
@@danielm4136 No. I don’t 😁
@didiekrudianto86303 ай бұрын
The analog joystick is still the same as the previous version, it is easily damaged, with a more complicated machine board, it is even more difficult to replace it, for some reason Sony doesn't make the analog one easily removable, even though I hope it is replaced with a socket model
@DIYVidss3 ай бұрын
Thanks for your attention 🌟
@TheDARKNESS80302 ай бұрын
What temperature did you have it to desolder? I tried today and could not get it it to separate
@DIYVidss2 ай бұрын
It’s 60w soldering iron … it doesn’t designate the temperature.
@Altnet893 ай бұрын
I opend it took out both "discs" and replaced them with those from old dualshock 4.
@DIYVidss3 ай бұрын
Yea … it works 👍🏻
@rajasnawar85455 ай бұрын
Hey can you help please i changed the sensor while ps5 was in rest mode added a ps4 sensor that white thing but while i pluged the battery got a orange light blink later when i put the cover and everything together still the orange light blinked when i pressed the ps button later found out ps4 sensor are different so that might be the issue so restored back old sensor still facing the orange light issue. Tried resetting by pin from back of the controller still just gives orange light any idea whats wrong
@DIYVidss5 ай бұрын
Ps4 stick and ps5 stick are the same in controller board … that could not cause a problem. Maybe other sockets are not properly fixed on the controller board.
@rajasnawar85455 ай бұрын
@@DIYVidss thanks for the reply
@talalfaisal7315 ай бұрын
@rajasnawar8545 do you fix your problem?
@vapenojutsuxllx60872 ай бұрын
Damn I thought he was a werewolf 😅😅
@tylerbecker41473 ай бұрын
I don't own a PS5 since I'm a Xbox player but opening a PS5 controller looks way more harder than opening a Xbox controller. This is why I prefer to not have a built in battery pack over either the choice of batteries or a interchangeable battery pack.
@DIYVidss3 ай бұрын
Appreciate 🌟👍🏻
@OTOOLE_MUSIC696 ай бұрын
Can you please fix my ps5 controller? The problem is stick dtift and i have no idea what to do
@DIYVidss6 ай бұрын
This video shows the absolute solution for this issue… the first try is cleaning the inside sticks with tuner spray and if it doesn’t work you have to change the stick on the ps5 controller board.
@OTOOLE_MUSIC696 ай бұрын
@@DIYVidss I dont know how tho
@kido36075 ай бұрын
@@DIYVidssdo you have a link to the stick module
@alejandrotobienne82205 ай бұрын
So it tears down like a Dual Shock 3?? Nice.
@chumpacena4 ай бұрын
no youre wrong
@GrainGrownАй бұрын
That looks WAY more complex than DS3.
@yyyrrrr42213 ай бұрын
Where I can find like your tools
@DIYVidss3 ай бұрын
From amazon or ali express 😀😀
@onitacular3 ай бұрын
The no flux is crazy 😳😳
@DIYVidss3 ай бұрын
Thanks for attention 🌟🌸
@DJDIRTYYELLA2 ай бұрын
My stick gets physically stuck.. (pause) is this a fix for that?😂 for real tho?
@user-ny8nw8yl3uАй бұрын
I have a novel idea,boycott Sony products until they put out a decent product .
@Unsubscribethispls3 ай бұрын
Damn.. next time I will buy duals. edge... freakin drifts...
@DIYVidss3 ай бұрын
Thanks for your attention 👍🏻🌟
@jerryfinger19673 ай бұрын
Ok so I did all of this and my right analog stick instead of drifting to the left now it just goes straight up and doesn’t stop, I can move sideways but not up and down at all it just goes up 😩😭 someone help me please
@DIYVidss3 ай бұрын
Change it again… unfortunately most sticks in shops are not work properly 😕
@DIYVidss3 ай бұрын
Change it again… unfortunately most sticks in shops are not work properly 😕
@Belik0nАй бұрын
Did you ever figure out the problem because I’m currently having this problem as well, and I need a solution
@Badangselatan4 ай бұрын
This required much patience that i dont have...so nah...if i have my ds5 broken,then i just send it for the guy who know how to fix it or i just buy the new one😂
@DIYVidss3 ай бұрын
Thanks for participating 🌟❤️😁
@user-kf9ws3zc9k3 ай бұрын
❤❤❤❤❤
@DIYVidss3 ай бұрын
Thanks for your attention 🌸🌟❤️
@gaimsharc71762 ай бұрын
This controller is an over-designed pos... to spend that much money for something so small to go wrong is a terrible customer service issue - the Xbox controller has the same issue, but accessing the components can be done in about 3 steps without the need to put the entire controller at risk
@DIYVidss2 ай бұрын
Thanks for your advice 👍🏻🌸
@Fortnitecodguy20 күн бұрын
Might as well buy a new one paying almost $20 and paying someone to do it 😂
@pattttttttt2 ай бұрын
We should never need to fix this. It's Sony that needs to fix it. Few of us aren't tech minded. Need to fork out for at least £35 to get it fix but aren't garrenteed either . I'm n uk
@DIYVidss2 ай бұрын
Thanks for commenting 👍🏻👌🏻
@rival20283 ай бұрын
Im just gonna buy a new pad. 😅
@DIYVidss3 ай бұрын
👍🏻😁
@stolentext94363 ай бұрын
My potentiometer is damaged, i cleaned it and it was a pretty good temporary fix. But i think ill order a solder tool and more potentiometers and joysticks. Soldering seems like a usefull skill to have.
@DIYVidss3 ай бұрын
Yes exactly… 👍🏻🌟
@bradley75065 ай бұрын
Nope, I’m not going to do that, I don’t trust myself to not screw it up. Going to just buy a new controller whenever I get stick drift.
@boubi93295 ай бұрын
Whats to lose if u going to buy a new controller anyway
@DIYVidss5 ай бұрын
Thanks for your attention 🌟❤️
@armenia19893 ай бұрын
pls buy soldering iron and flux paste😂😂
@DIYVidss3 ай бұрын
Thanks for your advice 😁🌟
@kirannaik5205 ай бұрын
I sucked my controller after watching this video
@DIYVidss5 ай бұрын
Why😂😂
@kirannaik5205 ай бұрын
I am unable to assemble 🙂 properly
@troytony805 ай бұрын
I fix them
@scenicroute6981Ай бұрын
😊😍😊😍
@SheZ.912 ай бұрын
It was quicker to buy new one
@DIYVidss2 ай бұрын
Precisely 😁👍🏻
@hitechmaster694 ай бұрын
Peggio di così si muore. 🤦🏻♂️🤦🏻♂️🤦🏻♂️
@attilatarjanyi54023 ай бұрын
Legit solution, horrible execution. If you do that you will definitely destroy one of the vias. The correct method would be either leave the green part on and just change the moving parts, or use solder wick or a solder sucker to remove the solder, in that way the pcb will not be damaged.
@DIYVidss3 ай бұрын
Yes exactly 👍🏻🌟
@angelbrace59625 ай бұрын
Why don't you just invest in a sucker instead of using a sim card release key. Smh
@DIYVidss4 ай бұрын
I just have a Soldering iron 😁😁
@haythamalexander3 ай бұрын
Good fucking lord the piece is hard to get to… if you don’t have the soldering tool, it is practically cheaper to buy a new controller 🤷🏼🤷🏼🤷🏼
@DIYVidss3 ай бұрын
Thanks for your advice 🌟🌸
@med_ssj4 ай бұрын
Incredible this s**t from sony...50% of dualsense or more with drift...i have 5 dualsense and 4 of them are with this problem
@DIYVidss4 ай бұрын
Yes… most ps5 controllers have this problem and it causes after less than 6 months usage…
@anderx54335 ай бұрын
Worst de soldering I ever seen😂
@DIYVidss5 ай бұрын
Thanks for your comment 😁❤️
@anderx54335 ай бұрын
no offence intended bro you do "anyway" ;)@@DIYVidss
@mikegyver19673 ай бұрын
With my friends, 4 controllers, over 1000 hours/years of play, and.....0 drift.
@DIYVidss3 ай бұрын
👍🏻😁😁
@SuiltDarkness6 ай бұрын
🤬😡ps5
@ajmj09684 ай бұрын
The Japanese game controllers fall apart in a couple of months. xbox controllers last from generation to generation
@DIYVidss3 ай бұрын
Yes exactly… ps5 controllers broken down after a few months 😕😕 specially their sticks.