I really need to do this to my daily driver car, as the passenger (right) side assembly has condensation, which is not only ugly, but also scatters the light, making them less effective at their job. TBH, I'm amazed that it's only that assembly that has condensation in it, as it's an over-20-year-old car, and so are the gaskets. Still going to caulk both of the assemblies, as I can guarantee you the other side does still need it, but hey, at least only the one needs dried

You did a great job. Thank you for helping me figure out how to get that condensation out of my tail light.

Best way (and a lot quicker) to do this is to hit the front of the lens with the hairdryer, hold it in one concentrated area until you see the droplets evaporate in front of your eyes, no chance of melting the plastic as the droplets will disappear before that ever happens. Move to another part of the lens, repeat, repeat until all gone. Took me 45 minutes to complete.

Good to see a Sista doin her thang! I am going to try this!!

Nice video. If you squirt the entire light with soapy water and add very little air pressure through one hole bubbles will show you where the leaks are. Remove both bulbs and air will flow through. It will cut your dry time by 1/4

Good job. Nice and easy video to follow. Thank you.

Thank you so much-Your method worked perfectly.

I have the same problem with one of my tail light assemblies. Your solution seems sound so I'll try it. Thanks for the vid.

Thank You so much you saved me so much $$$$ I will try this soon. ✌🏾💪🏾👍🏾👍🏾

Congratulations. A good job. I've seen a lot worse done by men who think very smart about it. In Portugal this tail light, if not repaired, would have problems with annual inspection and could not circulate on the roads. Police fines are very expensive for lack of inspection or broken or damaged parts.

Thanks Clare, i had the same problem , i copied your method, now my tail light is perfect. Great video 😄 10/10

Brilliant. Exactly the advice I was after!

Nicely done

Appreciate the video.

I'm about to do ths 2mro after work...fingers crossed..Nice vid hun🙏

Well done 👏

Well done. A Heat Gun can melt the lens! It might have gone quicker if you had left both bulbs out and let the air circulate out. I hope you got it sealed. You are one of few who knows how to fix these. I hope it worked , and that will depend on how well the sealing went.

Great video! Very handy to know that works instead of getting an expensive mechanic or a new headlight assembly. Could you do a video on how to remove and reinstall the headlight? I know not all cars are the same, but a general guide would be very useful.

On behalf of the rest of the world ...thank you

good job sista

If you leave your lights condensed on your car too long it will cause discoloration on the inside esp chrome areas..i made that mistake. Even tho the water is all dried up the inside is discoloured and dirty. Only way to fix them now is to take them apart and either clean with soap and towel or repaint the inside.

You SHOULD have opened all the holes so the air could circulate, which would have cut down on your drying time. Placing it in a 200 degree oven for about 30 minutes would have been quicker.

Could have dried out faster without blocking the holes. Just ssyin

Thanks so much for the knowledge! How much do you still work on vlogging?

Should have left vent holes...............would have all been done in a few min's............The hot air will expand and presurise the fitting............but needs a means of escape.

If the bulbs were not mounted it would dry much faster

I set my convection oven to 50°C and sit the assembly in for a couple of hours, done with no effort

You can run a blowdryer for 5 hours straight??

It would be nice to know if that was a permanent fix.

Is the time that passed minutes or hours later ?

funny

You have a very sexy voice. I also think it's cute that you made such a video 👍